MikroTik

Engitech

As we know. ... currently no new model. But we have some in stock at Engitech. Contact if you need some.

Engitech

Same problem. Windows not ok. Android and MacOS no problem. 7.1rc5 no change.

Engitech

yes - no problem.

Engitech

+1000 for Wireguard - performance,stability and simplicity

Engitech

Hello olivier
see this ..
https://www.mikrotik-routeros.com/2013/ ... s-success/

tested and still working with mipsbe HEX (don't have a rbm33g to test) -

yes 6x ethernet, the last is the usb dongle.

Engitech

Engitech

You need to set the "prefered source" on the route - it will set the outbound router ip address.

Engitech

try do add this:
/ip firewall mangle
add action=mark-routing chain=output new-routing-mark=mgmt src-address=192.168.88.1

i did a little test and seems to work

Engitech

/interface bridge port
add bridge="Main Bridge" interface=ether2

and

add address=192.168.1.250/24 interface=ether2 network=192.168.1.0

----->>> set ip on bridge not on ether2

Engitech

CCR1009 do it. I did the test in my MUM presentation Paris France 2016.

Engitech

6.37 and up

Engitech

Did you try this?

eap.PNG

Engitech

Hello
i see that you use Windows for the iperf test - can you redo the test with a linux distro? I did same setup and have very big difference if i use Windows or Linux distro.

Engitech

Hello
wih last 6.33rc version is more stable. Disable wifi of RB912 too. Like this is working pretty well.

Engitech

Hello
you have only to set the "prefered source" in the route of MT2 to MT1 in MT2 ROUTER- (and best too in MT1 router the same thing) - this way it will use corret ip to use the ipsec tunnel.

Engitech

Hello
did you try to do a nat rule:

add action=src-nat chain=srcnat dst-address=2.2.2.2 src-address=192.168.0.0/24 to-addresses=10.10.10.1

Engitech

I will try to post more information this week-end - no time now. But the setup was very basic. I do it only to see if the card that i have were compatible with new drivers. 3 channels used, omni mikrotik pigtail antenna , on a desk about 1 meter of distance - wifi signal registration indicated 1333M...

Engitech

Tested on RB912G-2HnD and 802.11ac QCA9880 mini-pcie card. Seems works well - 702 mbps udp between 2 of these.

Stable on bandwith test 1 hour.

Good job.

Capture1.PNG

Engitech

yes, 2 Mikrotik routers. contact me: office (at) engitech.ch

Engitech

The best and simple way is to replace the switch in the middle by a MikroTik router . Create 2 EoIP tunnel and bridge these with associated interface: 1st router (wan) wan1 = bridge1 (eth1 + eoip1 tunnel) wan2 = bridge2 (eth2 + eoip2 tunnel) 2nd router (in the middle) 1st customer = bridge1 (eth1 + ...

Engitech

write me an email directly at office(at)engitech.ch -

Engitech

And you test it with the router dir the linkectly attached to laptop (without switch) and with the version that i give you the link?

Engitech

Which ip address do you configure in your laptop and in netinstall configuration?

Engitech

Did you try the Netinstall version that i mentionned?

Engitech

I had the same problem with Netinstall . Use the version at this link : http://www.engitech.ch/netinstall-5.23-fixed.exe

it worked for me.

Engitech

we have some in stock - you can write me an email: office{at}engitech.ch

Engitech

Hello
can you do an export compact of the configuration?

Engitech

Use these screws to fix mini-pcie card.

Engitech

do you use port 9 and 10 of RB1200?

RB1200 has lot of problem on these 2 ethernet ports.

Engitech

We have a model that works fine with MikroTik - link: http://webshop.engitech.ch/index.php?ro ... uct_id=408

Engitech

I think you must do a netinstall of your router. It is a better way to reinstall your routeros if have you problem like this. 1) http://download2.mikrotik.com/routeros/6.0rc9/netinstall-6.0rc9.zip http://wiki.mikrotik.com/wiki/Netinstall 2) Run netinstall on your computer - connect router (eth1) to ...

Engitech

This is the only model that have this problem - if you take a RB1100hx2, no problem on any port.

Engitech

Model 1 or Model 2? If you use bridges, don't forget to use RSTP.

Engitech

There are problems with port 9 and 10 on RB1200. There are many posts on related to these 2 ports. Try to avoid to use these ports.

Engitech

try version 6.0rc12, it works better on this model -> http://download2.mikrotik.com/routeros/ ... .0rc12.npk

Engitech

Can you upgrade the firmware too. Go to system -> routerboard -> you can see current firmware, and upgrade firmware (write me back the 2 versions). -> Click upgrade - wait 10 seconds and reboot. return to system -> routerboard to see if upgrade is successful. After try again the usermanager package.

Engitech

if i understand: - you have a rb750 as router in your office. - you set a vpn server ont it (pptp server) for remote access. When user are login from external to your vpn server - the speed of browsing of these users is slow. It is because all of the traffic of these vpn users is going through your ...

Engitech

Can you do an export /compact?
Is this VPN connection only to reach some network ?

Engitech

in ip -> services , you can enable www-ssl and disable www.

Engitech

see zip attached.

Engitech

I have the same bug with version 6rc12 - it will normally be resolved in next version. If you want to generate the files, go back to version 5.24 and regenerate hotspot files or if you want i can send you a zip with the hotspot files.

Engitech

Do you use version 6.0rc12 ?
Which routerboard (rb951g)?

Engitech

vrrp doesn't work well on a bridge interface. You will have some strange behaviour. Use only vrrp directly on an ethernet interface.

Engitech

use this for upgrade: http://download2.mikrotik.com/routeros/ ... e-5.24.npk

copy this file to your router to upgrade.

After use the usermanager package contained in this file:

http://download2.mikrotik.com/routeros/ ... e-5.24.zip

Engitech

Use the mipsbe package - this is the good package for 951-2n.

Engitech

I think the main wireless problem of 951-2n was resolved with the last version of routeros (past version 5.22). I use 951g-2hnd for 1 month - very powerful and stable product, better than 751 series.

Engitech

you are right for the nat ... it was a bit late yesterday when i write my post. sorry. chain=dstnat action=dst-nat to-addresses=10.0.5.2 protocol=tcp dst-address=192.168.54.4 dst-port=8291 is the right syntax. But if you add the route you don't need it . Disable this nat rule. If you ping 10.0.5.2 f...

Engitech

1) you have no default-route on 10.0.5.2. Add a route to 0.0.0.0/0 with gateway 10.0.5.1. 2) this configuration is wrong: 2 chain=dstnat action=dst-nat to-addresses=10.0.5.2 to-ports=0-65535 protocol=tcp dst-address=192.168.5.4 you must remove it . if you want nat 1 port of your router 192.168.5.4 t...

Engitech

can you export the config of the 2 mikrotik (10.0.5.1 and 10.0.5.2)?

Engitech

Can you do an export /compact of firewall rules on 10.0.5.2?

Engitech

Can you do an export of firewall rules of this second router? I think ther is a rule that drop input.

Engitech

Did you configure that 10.0.5.2 can bypass the hotspot? Can you ping from 10.0.5.2 outside of his range (like 8.8.8.

?
Do you have a default route configured in this repeater?

Engitech

Can you verify is autonegation is ok (maybe duplex problem) and can you export the whole configuration.

Engitech

Yes, eth13 can be used to power this routerboard - you must use different voltage. If integrated power supply is 24v, use 12v for POE (don't remember if internal psu is 12v or 24v).
The board will use the PSU with higher voltage and failback on other.

Engitech

I think this setting is wrong, ether1 is part of bridge1, don't set an ip on it.

add address=192.168.1.33/24 interface=ether1 network=192.168.1.0

Engitech

I am too interested, please write me an email: p.robert at engitech.ch .

thanks!

Engitech

Hello you can create a probe that check snmp value of interface speed. I do it already to check autonegation speed between two routers. On a RB1200, for example i check the interface 1: SNMP OID 1.3.6.1.2.1.2.2.1.2.1 VALUE is ether1 SNMP OID: 1.3.6.1.2.1.2.2.1.5.1 VALUE is 1000000000 (1000000000 IS ...

Engitech

the ports that sould be redirected: Port 88 (UDP) Port 3074 (UDP and TCP) Port 53 (UDP and TCP) Port 80 (TCP) so you crrently have: 6 ;;; XBox Live chain=dstnat action=dst-nat to-addresses=192.168.60.15 protocol=udp dst-address-type="" in-interface=ether1 dst-port=3074 7 ;;; XBox Live chai...

Engitech

that's the nat rules ... give me the filter rules.

Engitech

Can you give me the Firewall filter rules that you use.

Engitech

I think the problem is with the profile you use ...
you use default-encryption - try default.

Engitech

No,i don't think it will work.

Engitech

Yes the routerboard 233 exist ... it is a old model with x86 cpu.
It is a mini-pci card with realtek 8139 - like the pci but mini-pci.

Engitech

First add the two address 10.0.0.3 and 10.0.0.4 to the output interface.

Create 2 rules for nat. one for each subnet. Specify the source address on each rule (192.168.1.0/24)
Don't use action masquerade but use action=src-nat, and write in to-src-address the ip of the output interface (10.0.0.3)

Engitech

Are the pc and the nas on the same lan? They don't use the same subnet 192.168.8.x and 192.168.1.x. and you don't use masquerade for range 192.168.1.x. .

Engitech

Hello i currently use RB 233 with a mini pci card based on realtek rtl8139cl and this works with no problem. I try to use this mini pci card on rb 411 and rb 800 and this card is not seen. Is there a support for this chipset on mips or ppc? Because i need to change these old board with newer (like r...

Engitech

try to delete the route and recreate it ... your interface for this route is not wan1 but pptp-in.

Engitech

In ISP1 router.

the route 2 is wrong.

You must have:
2 A S 192.168.1.0/24 172.16.0.2 1

Engitech

Hello
The problem is maybe with nat masquerading or forwarding rules.
In the Mikrotik_Server connected to ISP1 with IP: 250.*.*.* - Are these rules ok for range 192.168.0.0/24?

Do you have a route in this router to route 192.168.1.0/24 and use gateway 172.16.0.2 ?

Search found 68 matches