Community discussions

Search found 33 matches

by wwwevecom
Thu Sep 12, 2019 12:01 pm
Forum: Wireless Networking
Topic: 420Mbps inside trafic
Replies: 2
Views: 455

Re: 420Mbps inside trafic

Hello, I caught the villain. I named him 11 september hack . this is what helped me - block multicast on bridge /interface bridge filter add chain=forward in-bridge=bridge-vlan10-wifi-mall packet-type=multicast action=drop (optionaly mac-protocol=ipv6) /interface bridge settings set use-ip-firewall=...
by wwwevecom
Wed Sep 11, 2019 5:29 pm
Forum: Wireless Networking
Topic: 420Mbps inside trafic
Replies: 2
Views: 455

420Mbps inside trafic

Hello, I see a lot of traffic 400-500 Mbps, inside traffic with src address ff02::fb:5353; and Blocks the network???
by wwwevecom
Thu Jun 27, 2019 10:47 am
Forum: Wireless Networking
Topic: CAPsMAN Slowly turn on 5GHz band
Replies: 5
Views: 993

Re: CAPsMAN Slowly turn on 5GHz band

Ok thank you.
Is there a way to speed up, for example skip DFS or save selected? Or or with another setting?
by wwwevecom
Wed Jun 26, 2019 2:43 pm
Forum: Wireless Networking
Topic: CAPsMAN Slowly turn on 5GHz band
Replies: 5
Views: 993

CAPsMAN Slowly turn on 5GHz band

Hello, I have 3 pieces cAP ac - RBcAPGi-5acD2nd with 2,4 and 5GHz wifi. The problem is this: after factory settings works normally at 5785GHz, the two wifi adapters choose the frequency for 1-2 minutes. But when working in CAPs MAN system and when set higher frequencies than 5280GHz I have to wait 1...
by wwwevecom
Mon May 27, 2019 10:33 am
Forum: Wireless Networking
Topic: CAPsMAN channel selection
Replies: 7
Views: 1054

Re: CAPsMAN channel selection

if possible, To have a wall between access points.

Set access list -76..120 accept; -120..-77 drop if the points are close
or -120..-80 if the points are farther away
by wwwevecom
Thu May 23, 2019 12:35 pm
Forum: Wireless Networking
Topic: CAPsMAN channel selection
Replies: 7
Views: 1054

Re: CAPsMAN channel selection

Tx Power to 10 or less is too low for me. This will affect the scope range 12-13m. I think between 15-16dBm is good. I also had problems with a capsman, nearly two years. By noon he works and then stops. These settings saved me. Another very important. All devices that are not in this CAPSMAN system...
by wwwevecom
Mon May 20, 2019 10:38 am
Forum: Wireless Networking
Topic: CAPsMAN channel selection
Replies: 7
Views: 1054

Re: CAPsMAN channel selection

do not use reselect-interval, 1. Scan the room with WiFi analuzer with your phone to see the free frequencies 2. Set manualy Tx Powet 16 ot 17dBm (iphone transmit with 12-13 dBm) 3. Set manualy channel, may be close but different 4. set point by point. Run the first and go see if it works. if it is ...
by wwwevecom
Wed May 15, 2019 10:27 pm
Forum: Wireless Networking
Topic: 40MHz channel on hAP Mini
Replies: 4
Views: 397

Re: 40MHz channel on hAP Mini

Try to set country, if it does not happen to your country try Turkey
by wwwevecom
Fri Apr 26, 2019 11:59 am
Forum: Wireless Networking
Topic: CapsMan & CAP AC
Replies: 9
Views: 893

Re: CapsMan & CAP AC

hi, try here https://mum.mikrotik.com/presentations/ ... 854099.pdf
or you can try to buy here https://mynetworktraining.com/
I already bought 3 courses and has a great effect. maybe a remote support with him
by wwwevecom
Wed Nov 21, 2018 11:52 pm
Forum: General
Topic: How to give a priority for aaa radius user in front of local
Replies: 1
Views: 251

How to give a priority for aaa radius user in front of local

Hello, How to give a priority radius AAA login user in front of local?
When aaa is active, I wish I could not log in with local user.
Thank you.
by wwwevecom
Tue Jul 10, 2018 4:18 pm
Forum: Scripting
Topic: Cannot start scripts by names from netwatch [SOLVED]
Replies: 5
Views: 630

Re: Cannot start scripts by names from netwatch [SOLVED]

Thank You. Solved with script Policies:read, write, test and reboot
by wwwevecom
Tue Jul 10, 2018 3:47 pm
Forum: Scripting
Topic: Cannot start scripts by names from netwatch [SOLVED]
Replies: 5
Views: 630

Re: Cannot start scripts by names from netwatch [SOLVED]

Excuse me, I could not understand exactly what to do. I have to check script options in script Policies:read, write, test and reboot? Is that right?
by wwwevecom
Tue Jul 10, 2018 3:34 pm
Forum: Scripting
Topic: Cannot start scripts by names from netwatch [SOLVED]
Replies: 5
Views: 630

Re: Cannot start scripts by names from netwatch [SOLVED]

if I directly insert the text of the script then there is no problem.
There is no message in the log file that it has no startup rights
by wwwevecom
Tue Jul 10, 2018 3:17 pm
Forum: Scripting
Topic: Cannot start scripts by names from netwatch [SOLVED]
Replies: 5
Views: 630

Cannot start scripts by names from netwatch [SOLVED]

I have a created a script list. So far I have started the scripts as directly listing their names in tools/netwatch, like shown on picture After the last few updates stopped working the option that started the netwatch scripts with their names. So it's more convenient for clarity when starting two o...
by wwwevecom
Sat Feb 17, 2018 8:58 pm
Forum: Wireless Networking
Topic: capsman ping 50% loss [SOLVED]
Replies: 2
Views: 810

Re: capsman ping 50% loss [SOLVED]

I don't know how and why, but when I create wan port Trunk with 2 or 3 VLANs all works fine. I use only one vlan
by wwwevecom
Thu Feb 15, 2018 8:40 am
Forum: General
Topic: /interface ethernet set bandwidth=5M/5M in New 6.41
Replies: 0
Views: 287

/interface ethernet set bandwidth=5M/5M in New 6.41

Hello, I have RB2011UiAS. In old version 4.37 and 4.38 there was direct bandwidth limit for interface 1 to 5 (like on picture)-- /interface ethernet set bandwidth=5M/5M numbers=3
Where can find this settings, hopefully not removed
by wwwevecom
Tue Jan 30, 2018 4:23 pm
Forum: Wireless Networking
Topic: capsman ping 50% loss [SOLVED]
Replies: 2
Views: 810

capsman ping 50% loss [SOLVED]

Hi friends, I have CapsMan sys with 10 caps, all with the same 6.41 version I see a strange problem, if I configure newly bought RB951ui 2hnd router lika a Cap, I have not problem. But if router is not new , if I used it lika a router, for example for 1-2 years, then I configure lika a CAP - watchin...
by wwwevecom
Wed Mar 15, 2017 3:30 pm
Forum: General
Topic: bridge change mac address after update and messages for loop
Replies: 1
Views: 951

bridge change mac address after update and messages for loop

Hello, I have one RB 2011 UAS for ISP, 7 access points cAP2nD, and 5 RB951Ui-2hnD working as access points (one bridge and all ports and wifi in the same bridge ports). I set in all access points DHCP client on the bridge. RB 2011 working as CAPsMAN. Everything worked fine 7-8 months. Strange is tha...
by wwwevecom
Fri Nov 06, 2015 7:14 pm
Forum: General
Topic: ingress and egress tagging
Replies: 5
Views: 8730

Re: ingress and egress tagging

hi, Is there answer for me?
by wwwevecom
Mon Nov 02, 2015 8:38 pm
Forum: General
Topic: submask 22
Replies: 4
Views: 590

Re: submask 22

You have to make corection in:
1. ip address -- the mask
2. ip pool -- the range
3. dhcp server network -- the mask
4. and reboot.
If you have another mikrotik test there before on main router with clients
by wwwevecom
Sat Oct 31, 2015 7:27 pm
Forum: General
Topic: How can I create on Trunk mikrotik with Bridge
Replies: 9
Views: 1993

Re: How can I create on Trunk mikrotik with Bridge

yes, but eth8 is trunk port
by wwwevecom
Sat Oct 31, 2015 12:17 pm
Forum: General
Topic: How can I create on Trunk mikrotik with Bridge
Replies: 9
Views: 1993

Re: How can I create on Trunk mikrotik with Bridge

1. Set eth8 master port-->none 2. /interface bridge add name=bridge10 comment=toCisco 3. /interface bridge port add interface=ether8-slave-local bridge=bridge10 comment=toCisco disabled=no 4. /interface vlan add vlan-id=30 name=vlan30 interface=ether8 /interface vlan add vlan-id=40 name=vlan40 inter...
by wwwevecom
Fri Oct 30, 2015 8:51 pm
Forum: General
Topic: mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI
Replies: 4
Views: 839

Re: mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI

Ok, of course @CRS 212 Mall Varna] > system export verbose # oct/30/2015 20:40:55 by RouterOS 6.32.2 # software id = LLPZ-1YZS # /system logging action set 0 memory-lines=1000 memory-stop-on-full=no name=memory target=memory set 1 disk-file-count=2 disk-file-name=log disk-lines-per-file=1000 disk-st...
by wwwevecom
Fri Oct 30, 2015 5:16 pm
Forum: General
Topic: mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI
Replies: 4
Views: 839

Re: mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI

No, port is trunk and all VLANS is tagged
by wwwevecom
Fri Oct 30, 2015 3:42 pm
Forum: General
Topic: mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI
Replies: 4
Views: 839

mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI

Hi, I noticed mismatch VLAN 1 in mikrotik and VLAN 1 in 3Com 5500G-EI. I have 5 swishes 3com which is communicated in star with ip addresses in interface VLAN 1. When I put mikrotik CRS212 between two 3com switches and add vlan 1 tagged in mikrotik, I have no ping. When add and enable VLAN 0 in mikr...
by wwwevecom
Fri Oct 30, 2015 12:00 pm
Forum: General
Topic: ingress and egress tagging
Replies: 5
Views: 8730

Re: ingress and egress tagging

Hello, I have another question about this issue: What is the difference between thees two menus VLAN Tagging and eg. VLAN tran.(1 and 2 on picture). I have CRS212-1G-10S-1S+IN and add tagged vlans in menu (1) - VLAN Tagging (on picture) with command: /interface ethernet switch egress-vlan-tag add ta...
by wwwevecom
Mon May 11, 2015 10:09 pm
Forum: Wireless Networking
Topic: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951
Replies: 7
Views: 2230

Re: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951

Is it possible bad antenna quality. I use small D-link with N-male adapter
by wwwevecom
Mon May 11, 2015 10:02 pm
Forum: Wireless Networking
Topic: Connect Groove 52HPn as wifi client to RB951Ui-2HnD
Replies: 4
Views: 1088

Re: Connect Groove 52HPn as wifi client to RB951Ui-2HnD

I forgot to say that I use N-male adapter and small antenna
by wwwevecom
Thu May 07, 2015 12:47 pm
Forum: Wireless Networking
Topic: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951
Replies: 7
Views: 2230

Re: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951

L3 does not allow to set ap. There is no problem with connecting L3 device as client to any other ap. Your problem surely lies elsewhere. Yes I know L3 does not allow to set ap. I have 7 pieces Groove 52HPn(level 3), when I try connect Groove 52HPn(level 3) as a client to RB951Ui-2HnD(level 4), no ...
by wwwevecom
Thu May 07, 2015 12:23 am
Forum: Wireless Networking
Topic: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951
Replies: 7
Views: 2230

Re: Would like to use Mikrotik RouterBOARD Groove-52HPn and Routerboard 951

hi,I have seven grove 52hpn, 28pieces - RB951ui and two RB2011hnd. Groove 52hpn can connect to 2011hnd (license 5 level) and work perfectly, but cannot connect to RB951. I tryed 10 days with different configurations: dhcp, static ip, router bridge and for me it is impossible to work groove 52hpn(lev...
by wwwevecom
Wed May 06, 2015 11:49 pm
Forum: Wireless Networking
Topic: mikrotik NetMetal 5 unable detect wireless interface
Replies: 6
Views: 1790

Re: mikrotik NetMetal 5 unable detect wireless interface

hi, 1. Do a button reset: http://wiki.mikrotik.com/wiki/Manual:Password_reset 2. check instalation: system/packages/ check instalation. From there you can enable and disable packages. Swich all to enable and check them. If there is no errors but not working 3. then reinstall with netinstall: http://...
by wwwevecom
Fri May 01, 2015 11:22 pm
Forum: Wireless Networking
Topic: Connect Groove 52HPn as wifi client to RB951Ui-2HnD
Replies: 4
Views: 1088

Connect Groove 52HPn as wifi client to RB951Ui-2HnD

Hi, I bought 7 pieces Groove 52HPn(level 3) and I want to connect as wifi clients to RB951Ui-2HnD(level 4). I try several ways: Groove 52HPn like bridge or like a router, CPE or PTP bridge... Maybe It is not possible(distance is 200m)? Groove 52HPn blocks and disconnect me from winbox and I cannot g...