Hi all, when I do a Torch on any of the interfaces on CCR1016-12S-1S+ all current connected PPPoE sessions immediately fall to 0 bps RX and after a while disconnect one by one. As soon as I stop Torch, the connected PPPoE sessions go back to normal with RX and disconneted sessions reconnect again. F...

to which ROS have you downgraded please? Same issue here with 6.40.6.
After upgrade all the upload queues are not shaping the traffic anymore... subscribers can use full line speed!

yes, same thing here... any solution/setting found? (I'm on 6.40.6 tile)

Well, I got DNAT running to internal IP but this won't be logged by OUTPUT rule. INPUT allowed is 8291 and another one for SSH administration only. At the moment the box is trying to reach millions of IP's at Ports 8291, 80, 8080, 7547, 23 and flooding the box' log ... this sounds like VPNFilter vul...

Hi all, Spamhaus was blocking my public IP for sending TCP packets with identified conficker signature to specific IP addresses. "This IP address was detected and listed 9 times in the past 28 days, and 1 times in the past 24 hours. The most recent detection was at Fri May 25 13:45:00 2018 UTC ...

After yesterday's "URGENT security advisory" from Mikrotik I upgraded my PPPoE Servers to 6.40.6 and now same thing: MSS mangle rules gone and service broken!

Please help!

since I’ve upgraded my RB750GL from 6.3x to 6.4x I experience sporadic packet loss through the automatic generated bridge with hw-offload. Before upgrade and master-slave switch port config there wasn’t any of that kind of problems. There was ether3 and ether4 in a switch config with ether4 as maste...

Can you check if the following part exists on the legs of the HC595 chip? _DSC0579.jpg Hi Normis, what can be the issues caused when that part is missing? I currently have rolled out a bunch of 493G's which - after 6 weeks of operation - start to crash and reboot periodically. I have no idea as to ...

Hi all, one thing that saved my life and is running for months now without any FCS errors is the following (RB750 had this issue with NanoStationsM5): Before: ports (except customer port) bridged and linked to another bridge (with customer port) via vlan --> port where UBNT gear was operated: lots o...

Hi everybody, I'm currently having same issue here, FCS errors on RB750GL (on 6.15) port with UBNT NS5 Loco (latest firmware and RF Armor shields) connected. NS5 Loco is powered by PoE injector. What I did so far without success: - replaced cable (tough cable) connectors - replaced cable by certifi...

Hi everybody, I'm currently having same issue here, FCS errors on RB750GL (on 6.15) port with UBNT NS5 Loco (latest firmware and RF Armor shields) connected. NS5 Loco is powered by PoE injector. What I did so far without success: - replaced cable (tough cable) connectors - replaced cable by certifi...

Hi everybody, I'm currently having same issue here, FCS errors on RB750GL (on 6.15) port with UBNT NS5 Loco (latest firmware and RF Armor shields) connected. NS5 Loco is powered by PoE injector. What I did so far without success: - replaced cable (tough cable) connectors - replaced cable by certifie...

thanks for your reply! that's what I'm currently doing with 2x2 only chains. But in future setups I want a fdx/failover solution by using the 4x4 with ospf and doing 2x2 for TX and 2x2 for RX on both AP and Station panels (WiBox) and the relatively new RB912UAG-5HPnD-OUT with additional 2x2 card. I'...

I'm planning to build full duplex backbone using ptmp between 1 ap and 2 stations like this: S -----AP----- S. Thinking of 4x4 MIMO panels and OSPF with VPLS instead of EoIP to max out Speed and MTU. Background is to avoid wasting frequencies in a scenario like this: S ---AP_AP--- S Do you think tha...

Hi, new findings after a lot of testing (currently with 6.1): after doing a "Reset Configuration" with "No Default Configuration" and turning off CPU eating things like Conn. Tracker, I got a good RTT with minimum jitter going back and forth from 2ms to 4ms running none or low t...

Hi, new findings after a lot of testing (currently with 6.1): after doing a "Reset Configuration" with "No Default Configuration" and turning off CPU eating things like Conn. Tracker, I got a good RTT with minimum jitter going back and forth from 2ms to 4ms running none or low tr...

don't know what the above pings should prove/show...

but I was referring to this:
"I would try setting my interface types to NMBA(nonbroadcast multi access) and configuring some OSPF neighbors. This will kill multicast and switch all communication to unicast."

How I found it out? as I said: by playing with the settings... in a lab environment and a hundred combinations I excluded several settings that would make sense,up to this one which absolutely makes no sense to me ;-) Well, regarding your OSPF issue I would try this post from gregsowell: http://foru...

Hi wispwest, I've noticed same behaviour when I was updating from 5.25 to 6.0 and all my <1ms PtMP links increased both latency and jitter. Going back to 5.25 or 5.20 did not help at all: with unchanged settings worse results... really annoying! I'm currently trying to find a most satisfying config ...