Community discussions

MikroTik App

Search found 32 matches

by mikronab
Thu Oct 10, 2013 12:21 pm
Forum: General
Topic: SwOS
Replies: 1
Views: 1125

SwOS

Hi, Are there going to be any larger products coming out that support SwOS? Currently i only found RB260GS and RB250GS and being limited to 5 ports just rules out convincing the client to go MikroTIK. A 24 port would really seal the deal, but if there were any other solutions to Broadcast Storm Cont...
by mikronab
Wed Mar 20, 2013 9:43 am
Forum: General
Topic: VPN
Replies: 4
Views: 971

Re: VPN

Hi,

Thanks for the help. It is working now without changing settings on my end. I don't have access to the concentrator. It is run by another company and must have been where the problem was coming from.

Thanks again
by mikronab
Mon Mar 18, 2013 8:40 am
Forum: General
Topic: VPN
Replies: 4
Views: 971

Re: VPN

Hey there!

We are making the initial connection with GRE (int> gre tunnel) and then running OSPF on top.
by mikronab
Fri Mar 15, 2013 9:53 am
Forum: General
Topic: VPN
Replies: 4
Views: 971

VPN

Good day, I am having trouble setting up a VPN connection. I initially had it running on the 41.220.XX.30/30 address. We needed to increase our Public IP range. Instead of having the 41.220.XX.30/30 range increased or changed, a new range was forwarded to that exisiting 'Link IP'. The new address ra...
by mikronab
Tue Feb 26, 2013 8:29 am
Forum: General
Topic: Cisco Conversions
Replies: 3
Views: 1069

Re: Cisco Conversions

Hi and thanks for the reply.

Could you provide the code for ROS pls.

I thought of ip firewall nat add chain=dstnat port=445 action=dstnat to addresses=172.17.8.50 to ports=445 but im not much of an expert on firewalling.

regards
MNub
by mikronab
Mon Feb 25, 2013 4:55 pm
Forum: General
Topic: Cisco Conversions
Replies: 3
Views: 1069

Cisco Conversions

Good Day, Wondering if anyone could help me. I am going to install an MTK at a clients side and he ahs a few rules i wish to convert from his Csico setup to MTK. One rule he has is ip nat inside source static tcp 172.17.8.50 445 interface FastEthernet0/1 445 Does anyone know what this would be in mi...
by mikronab
Mon Feb 25, 2013 10:32 am
Forum: Wireless Networking
Topic: Proxy Login
Replies: 1
Views: 916

Proxy Login

Good day,

Is there a way on MTK i could have a login feature similar to hotspot the runs on the Proxy only?

Regards
MNub
by mikronab
Mon Feb 25, 2013 9:17 am
Forum: General
Topic: Public IP to Local Client
Replies: 2
Views: 977

Re: Public IP to Local Client

Hi and thanks for the reply.

Is it possible if you could help me on some configs for this? Routing is not my strong suite and I don't have another connection to test on and the risk of downing my entire client base is not one I am willing to take :)

Regards
MNub
by mikronab
Thu Feb 21, 2013 11:09 am
Forum: General
Topic: Public IP to Local Client
Replies: 2
Views: 977

Public IP to Local Client

Good day, I have the following setup WAN- 88.X.X.194/30 LAN- 10.10.10.1/24 I have several High Sites in the 10.10.10.0/24 field and on one specific one(WAN- 10.10.10.17 Lan - 172.18.0.254/24) there is a client (172.18.0.77) who needs a Public IP. 2 questions. Firstly, would I be able to forward the ...
by mikronab
Mon Feb 11, 2013 9:56 am
Forum: General
Topic: Hotspot and LAN services
Replies: 4
Views: 1328

Re: Hotspot and LAN services

That is weird. I could have sworn I saw that once before, but you are right, it is not "none" by default. Regardless, I had set "address-pool=none" and it made no change. I took a new 1100AH to site because of network load and installed without any problems (and after switching t...
by mikronab
Tue Feb 05, 2013 8:12 am
Forum: General
Topic: Hotspot and LAN services
Replies: 4
Views: 1328

Re: Hotspot and LAN services

ip>hotspot. set 0 address-pool=none has been mentioned a few times to do with ARP poisoning. This was set to none by default. hi. thanks for the response. yeah ive seen this mentioned many times in other topics, but since it was set to that by default, is there much else i could do? ive got a setup...
by mikronab
Mon Feb 04, 2013 4:10 pm
Forum: General
Topic: Hotspot and LAN services
Replies: 4
Views: 1328

Hotspot and LAN services

Good Day. I have a strange problem. I setup hotspot on an existing network by setting my mikrotik as the gateway and simply swapping it out for the Cisco that was there. The hotspot is fine and running well. The problem now comes in on the local LAN services. People who once had shared files and doc...
by mikronab
Wed Dec 19, 2012 12:11 pm
Forum: Forwarding Protocols
Topic: Pcc and Hotspot
Replies: 2
Views: 1593

Re: Pcc and Hotspot

i did the following changed to the pcc and it seems to be working well. 1 chain=srcnat action=masquerade src-address-list=!Student out-interface=ISP1 This does not allow address list Student to nat to ISP1. 4 chain=prerouting action=mark-connection new-connection-mark=ISP1_conn passthrough=yes dst-a...
by mikronab
Wed Dec 19, 2012 8:09 am
Forum: Forwarding Protocols
Topic: Pcc and Hotspot
Replies: 2
Views: 1593

Re: Pcc and Hotspot

any suggestions?
by mikronab
Mon Dec 17, 2012 12:40 pm
Forum: Forwarding Protocols
Topic: Pcc and Hotspot
Replies: 2
Views: 1593

Pcc and Hotspot

Good Day I have setup PCC and Hotspot with different profiles (3 in total) each having their own address list tags. I want to limit 2 of the profiles so that they may not access Wan1. All attempts have not worked 100%. I tired the following where "src-address-list=Staffs" is the variable f...
by mikronab
Mon Dec 10, 2012 2:29 pm
Forum: General
Topic: Tx CCQ
Replies: 5
Views: 2544

Re: Tx CCQ

Thanks everyone for the input. To answer a few questions. I did bandiwdth tests from RB to RB and i had no increase in Tx CCQ at any stage. It stayed around 20% max. I also turned off the other radios in the area and it did improve but max was 2mbps and still fluctuating. There are plenty more radio...
by mikronab
Fri Dec 07, 2012 11:07 am
Forum: General
Topic: Tx CCQ
Replies: 5
Views: 2544

Re: Tx CCQ

Hi Uldis. Here are the settings of my AP /interface wireless> pri Flags: X - disabled, R - running 0 R name="wlan1" mtu=1500 mac-address=00:XX:XX:32:33:XX arp=enabled interface-type=Atheros AR5413 mode=ap-bridge ssid="....." frequency=2402 band=2ghz-b/g channel-width=20mhz scan-l...
by mikronab
Fri Dec 07, 2012 9:03 am
Forum: General
Topic: Tx CCQ
Replies: 5
Views: 2544

Tx CCQ

Hi all.

Please take a look at 2 sites ive set up to an AP. They seem to be getting quality signal, but the TX CCQ is quite low. might this be to do with the type of antenna or wireless card I am using?

thanks in advance.
by mikronab
Mon Dec 03, 2012 9:00 am
Forum: General
Topic: Forwarding VPN to local network
Replies: 2
Views: 1037

Re: Forwarding VPN to local network

Any ideas on this?
by mikronab
Mon Nov 26, 2012 4:31 pm
Forum: General
Topic: Forwarding VPN to local network
Replies: 2
Views: 1037

Forwarding VPN to local network

Hi all. I have a VPN setup using IPIP and OSPF. Running like a dream. I am now terminating the connection it is running on and want to run my entire network on my backup connection. Attached is a network diagram. The top is the existing setup where X.X.X.X network runs transparently on my network. I...
by mikronab
Mon Oct 15, 2012 5:00 pm
Forum: Scripting
Topic: Reboot Upon Timeout
Replies: 1
Views: 1164

Reboot Upon Timeout

Hello. I am having issue where Routerboard goes dead. Maybe 1 time in a day or more. Completely at random. If i physically on/off unit comes on.. but not for long. Until i debug issue is there script that can help me to reboot unit when board is no longer reachable (also unreachable via MAC). I am t...
by mikronab
Thu Aug 23, 2012 11:52 am
Forum: General
Topic: PCC Specific Tunnel
Replies: 1
Views: 647

PCC Specific Tunnel

Hi there!

I have made PCC on my main router all is great! A problem i am having is one interface is choosed more often that the other. How can i force specific traffic like mails and pings through one interface?

Thanks!
by mikronab
Sun Jul 29, 2012 6:55 pm
Forum: General
Topic: hotspot user
Replies: 1
Views: 738

hotspot user

hi. how can i create a hotspot user that never expire? the admin must be on same lan to share printer. i set profile with no limit but it keep on losing setting? the actual account is removed from usermanager? how to set unlimited time and never to expire! help pls! :D
by mikronab
Fri Jul 27, 2012 4:51 pm
Forum: General
Topic: pcc giving problems
Replies: 10
Views: 2353

Re: pcc giving problems

yes it is nating. so if giving 1 ip then will cause b/w to go through 1 isp. is a shame is nice technology! taking that 'firewall' mt away all b/w is being used! :D
by mikronab
Fri Jul 27, 2012 12:15 pm
Forum: General
Topic: pcc giving problems
Replies: 10
Views: 2353

Re: pcc giving problems

sry my network diagram was not very clear. dont know why it changed after post! the router doing the load balancing has 1 IP on LAN. 1 ip that connecting to load balancing router. it is firewall router. would that not mean that all traffic from src address would use only one ISP? because thats what ...
by mikronab
Fri Jul 27, 2012 11:43 am
Forum: General
Topic: NOT TO DO. Weird instalations?
Replies: 385
Views: 282692

Re: NOT TO DO. Weird instalations?

Our local ISPs at their best! ;)

See how they mounter the box to the wall? genius!
by mikronab
Thu Jul 26, 2012 3:56 pm
Forum: The User Manager
Topic: account expiration
Replies: 12
Views: 11058

Re: account expiration

hello all. i creating superuser profile to ensure sharing of printer in internet cafe. same lan etc. how to make so that account will never expire? leaving blank or to put 0D?
by mikronab
Thu Jul 26, 2012 3:20 pm
Forum: General
Topic: pcc giving problems
Replies: 10
Views: 2353

Re: pcc giving problems

i have the following setup. 2 ISPs. -> MTK Load balancing -> MTK Firewall -> LAN with 7 src addresses. 10.X.X.1 10.Y.Y.1 I activate this setting of 'use src address'. It working well with banks! But now traffic utilization is max on one ISP and the other have almost none. Might 'MTK Firewall' having...
by mikronab
Thu Jun 28, 2012 11:58 am
Forum: Wireless Networking
Topic: Tracking Usage
Replies: 2
Views: 977

Re: Tracking Usage

No one has any ideas!?
by mikronab
Thu Jun 28, 2012 11:55 am
Forum: Wireless Networking
Topic: Calculating throughput
Replies: 2
Views: 1330

Re: Calculating throughput

Thanks you for the reply! Sorry i have been traveling but am now back in my home town. On the distance i imagine you mean on the client units? on wireless protocol i leave as unspecified. is this bad? one other unrelated issue. the channel that i have been issued by ISP is causing low throughput. Se...
by mikronab
Tue Jun 19, 2012 10:36 am
Forum: Wireless Networking
Topic: Tracking Usage
Replies: 2
Views: 977

Tracking Usage

Greetings! I would like to know on how to track a users total tx/rx bytes for certains period. I am viewing this in simple queues and it is quite good, but moment the router reset it lose all setting. Maybe there is script to store this every week or whenever power is lost (this happen a lot in my c...
by mikronab
Wed May 02, 2012 11:13 am
Forum: Wireless Networking
Topic: Calculating throughput
Replies: 2
Views: 1330

Calculating throughput

Hi guys. I have an AP running 2 sectors in 2.4 range and a few clients. I have a client connection that set up to see end user performance. At time the i cannot connect to the AP. I saw the registration and see that one client has 1mbps throughput due to low signal. If the AP was pushing 1mbps would...