MikroTik

RcRaCk2k

Thats very bad, because there is no PBR support for IPv6 in ROSv6.xx.

I will try to get my hands on the v7 BETA... Hope that my current setup will work in v7 current development state ;-)

RcRaCk2k

So we have to upgrade to v7 BETA to get PBR working on IPv6?

Is it save to run v7 BETA on a provider network yet?

RcRaCk2k

Hi Guys,

why is IPv6 in an IPIP tunnel not working?

I have a IPIP Tunnel Interface and have added an IPv6-Address to that interface.
But both ends can not see each other?!?

IPv4 works.

Is there some missconfiguration or is mikrotik not capable in encapsulate IPv6 in IPIP-Tunnels?

RcRaCk2k

Bonding Since RouterOS v6.42 all CRS3xx series switches support hardware offloading with bonding interfaces. Only 802.3ad and balance-xor bonding modes are hardware offloaded, other bonding modes will use the CPU's resources. You can find more information about the bonding interfaces in the Bonding...

RcRaCk2k

Hi Guys, how can i get the switch to do hardware-offloading with "balance-rr" ? What i am doing wrong? Firmware: v6.47.3 Device: CRS326-24S+2Q+ MMM MMM KKK TTTTTTTTTTT KKK MMMM MMMM KKK TTTTTTTTTTT KKK MMM MMMM MMM III KKK KKK RRRRRR OOOOOO TTT III KKK KKK MMM MM MMM III KKKKK RRR RRR OOO ...

RcRaCk2k

Is there nobody out there discovering the same issue?
All my CRS326-24S+2Q+ devices with current firmware is showing that issue.

RcRaCk2k

Oh yeha, now i see, the config-export was cut in half. Dont know why. I have updated the initial post with the correct config-export. For instance VLAN in this case is not correct and I think this may break the offloading. You need to implement VLAN filtering on the Bridge and add the add the manage...

RcRaCk2k

Your config is way off. The config really needs to be mainly done via the bridge. Here is the link for vlans with bonds on the crs3xx series. https://wiki.mikrotik.com/wiki/Manual:CRS3xx_VLANs_with_Bonds This is exactly how i did the configuration. In most cases, i unpack the switch, and only chang...

RcRaCk2k

Sorry Guys, but is Mikrotik kidding me? I have a CRS326-24S+2Q and i having trouble to get 250 MBit/s out of that switch. All ports are HARDWARE-OFFLOADED, but the CPU goes that high, that the traffic caps at 250 MBit/s. Core fucked up.JPG Why is this happening? Yeah i know i should update firmware ...

RcRaCk2k

I ran into that issue twice. CRS326-24G-2S+ Current Firmware: ROS v6.44.5 The switch locks up and is not able to communicate via IP (SSH, Telnet, MAC-Telnet, WinBox, arping). Only powercycle will bring the switch back into life. We use the SFP1-Port for Upstream with an Fiber-Switch. On the fiber-sw...

RcRaCk2k

I miss that option too. I have a link that is 900m long and the RSSI is fluctuating. Even the link goes down. That there is an A-TPC active is clearly visible. But the programming of that A-TPC mechanismen is not good at all. Every 30 Minutes the link goes down. But is not exactly 30 Minutes. Someti...

RcRaCk2k

I think that Mikrotik have to work on many things to get a real game changer.
Missing L2TPv3 is a nogo. Linux-Kernel supports L2TPv3 so there is only some work in programming wrappers from ROS-Configuration to Unix-Commands.

RcRaCk2k

How have i to setup "Set In Nexthop" on Actions-Tab as @heribertos suggested?
What value have to be in there?

RcRaCk2k

Hi guys,

my Interface Activity is not shown on the LEDs because i can not see *-led2 in my settings, there is only *-led1 (Speed-LED).

What can i do to make the LEDs working again?

Firmware: 6.47

Mikrotik Failed.JPG

RcRaCk2k

Hi Guys, i have a 57V powered site. I like to use CRS326-24S+2Q+ in there. As there is no DC-IN currently, what will be the best option to get the switch running with the provided power of 57V? It is bad, that there is no Power-Bay, so you can Switch the AC-Blades to DC-Blades. Is the only way, to o...

RcRaCk2k

Came to that point today and i am disappointed that mikrotik developers are not able to give us some information if that feature is on a todo list or not.

RcRaCk2k

Hi guys, i have a PowerBox Pro mounted outside on the tower. The PowerBox Pro is powered via ETHER-1 POE-IN. There is a Rocket-M5 connected on ether-4 and a PowerBeam M5 connected on ether-5. Both devices will be powered via the PowerBox Pro. The both APs are rebooting randomly at the same time. PoE...

RcRaCk2k

But there is no gateway on the 93.240.147.64/29 subnet.
That is why i need an interface-route.

RcRaCk2k

That means, that Mikrotik is not the correct router for this situation?
So i have to switch to a other vendor like ubiquiti?

But why is my first route not working?
dst-address=0.0.0.0/0 gateway=IP-ADDRESS%INTERFACE

That should do the trick, but why it wont work?
I am a little bit confused.

RcRaCk2k

Hi, i have done the scope-settings, but it will not work as expected. Can you please have a look on that? [admin@MikroTik] > ip route print detail Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit ...

RcRaCk2k

Hi Guys, i have two networks on the same LAN: #1 192.168.0.0/29 (The Router is .1) #2 192.168.1.5/29 (All IPs are useable 1-7) There is only one default-gateway on LAN#1 but both networks are on the same LAN (so no VLAN is configured). My Router is 192.168.1.5 and i can do an arp-ping to 192.168.0.1...

RcRaCk2k

I will give it a try.

A user already confirms that the SFP i currently use is now supported.
viewtopic.php?f=21&t=139057&p=709663#p709975

RcRaCk2k

Hey Guys, i have a RB4011 with current stable firmware. My SFP is a 1 GbE SFP from FiberStore, branded as JUNIPER. It is a BiDi 1550/1310nm (yellow marked). Per second the link flaps. Also the UI shows (Running, Standby, Running, Standby....) https://youtu.be/-xBT-wZGTe0 The same SFP is funktional i...

RcRaCk2k

@alexcherry what is your configuration looking like? Please send me your configuration i will give a try on that. Agent-Circuit-Id should be configurable with placeholders like %m = MAC-Address of Interface %n = Name of Interface (custom name) %i = ID of Interface XX (eg 01, 02, 03....) The informat...

RcRaCk2k

Hey Gusy, there is issue in your code. When i request the "Hosts"-Tab, the json-output looks like that: [{adr:'fa94f6af57ad',prt:0x01,drp:0x00,mir:0x00,sts:0x07,vid:0x0001}, {adr:'d4ca6d1bf485',prt:0x00,drp:0x00,mir:0x00,sts:0x07,vid:0x0001}, {adr:'dc9fdb28c387',prt:0x01,drp:0x00,mir:0x00,...

RcRaCk2k

Hey Guys, is it possible to get DHCP-Snooping Option 82 running on ROS? We like to add interface-informations to a DHCP-Client-Request (DHCP Option 82). We install Mikrotik Router-Boards in buildings to get more than just one customer connected. To know, which customer have requested a DHCP-Lease we...

RcRaCk2k

Hey Guys,

i use RB960PGS and power the device via PoE. I use a Ubiquiti PoE-Adapter wich was powering an 5AC Rocket before with Gigabit connection on LAN. After connecting the RB960PGS the interface came up with 100M only.

How can i use Gigabit-Speed with RB960PGS with PoE-IN used?

RcRaCk2k

Hi! I want to limit a customers Ethernet-Port to 200M/50M (down/up). The RouterBoard does strange things, when bridge will enable "Use IP firewalling". # dec/01/2015 15:44:05 by RouterOS 6.33.2 # software id = N68D-40SQ # /interface bridge add name=br1-internet protocol-mode=none /interfac...

RcRaCk2k

Hey, is there a solution for this issue?

RcRaCk2k

+1 for that feature.

RcRaCk2k

Hey Guys! We are using RB260GS and RB260GSP in our Fiber-Network to bring our customers online via Fiber. So our customers are connected to Port 1-5 and the Uplink is via Gigabit-SFP. To limit the bandwith we are using ACL, but we achieved very stupid things when using the FROM and TO Filter the sam...

RcRaCk2k

Hi!

My RB260GS will return a octet stream when i am accessing the WebInterface.

What is wrong with that device? I did not change anything. From one day to other it stops working.

RcRaCk2k

Hell yeah! What is this for a creepy issue? Why is there no ! / NOT implemented? I also need this Feature. Also there is no ability to select a Out-Interface. I like to limit the bandwith for some destinations. I sell 20/2 MBit to a customer which is connected to a 1 GbE via SFP. But within my Netwo...

RcRaCk2k

Hi all!

I've bought a RB260GSP to feed my Ubiquiti Hardware with passive PoE.

If i connect the Ubiquiti Hardware to the RB260GSP the Switch says "Short Circuit" and the red Led is blinking.

Is this Switch not able to PoE my Ubiquiti Device? The regular PoE-Adapter works fine.

RcRaCk2k

Charge the customer for that. Yeah, we do, but we always have a discussion with the customer about the fees. In our General Agreement Terms, there is a special article about manipulating devices owned by the ISP. There also specified the fees for repairing. But if our network goes down (for mainten...

RcRaCk2k

Hi! We use the RB260GS to bring our customers to our Fibre-Network. We use Ethernet-Connection and DHCP. The Bandwidth is limited by RB260GS via Egress rule and ACL-Rule. Some our customers are so cunning, that they use the Hardware Reset-Button to gain 1.000 MBit Connection. That is not what we wan...

RcRaCk2k

Very terrible but useful

Thank you.

RcRaCk2k

Hi! I need to forward DHCP-Requests to a upstream DHCP-Server. I also need the following capabilities to do so: * Set DHCP-Sub-Option "Link Selection" - RFC3527 * Set DHCP-Sub-Option "DHCP Server Identifier Override" - RFC5107 Is Mikrotik capable of these DHCP-SubOptions? If not,...

RcRaCk2k

I think they will have a general problem with SFP and RB260GS!!! RB260GS - SFP Module - Not working - no RX just TX http://forum.mikrotik.com/viewtopic.php?f=17&t=83873#p422216 That is so so annoying! Whe have currently 30 Switches in the field and have 80 pcs encamped. We will immediately stop ...

RcRaCk2k

100m MM patch cord. Unbelievable !!!! After resetting both devices to "Factory defaults" the modules worked. I made 3 power cycles and the Fibre-Link was established and working fine without one interruption. I did not configure anything, after i picked the units from packaging. I have ins...

RcRaCk2k

Sorry, but anything is wrong with the RB260GS. Now i ordered new SFPs with Multimode to test both RB260GS units. Both SFP-LED are on, but there is no data communication between both devices. I tested both SPFs in two TP-LINK Switches and in DELL Switches. In both switches, the modules worked fine. S...

RcRaCk2k

Your config is wrong.

If Port 5 is your trunking port, it have to be a member of the vlans.

Tab "VLANs" Port 5 is not a member of 11, 1 and 12.

Also Switch Upstairs... Port 1 is not a member of 11, 1 and 12.

RcRaCk2k

I hope this feature gets implemented in next release.

RcRaCk2k

The Module provides 19dB of output. The physical attenuation is at 12dB, so 7dB is enough for the link to work. I replaced the TP-Link MC220L with a RB260GS, the link comes up but i have no RX. On Side A, the SFP-Link-LED is on. On Side B the LED is off.. That is odd. SFP Auto Negotiation Module Pre...

RcRaCk2k

Hi!

Currently i am using TPLINK-MC220L. This Device supports only modules up to 10km.
I have installed a 40 km Module, but after 15km the signal were loss.

Now i like to use RB260GS. Is this Model able to power up a 40km SFP Module?

Thanks.

RcRaCk2k

I also have problems with loops. But my setup is very simple and was working, before i used RB250GS! I think, there is a problem. Also a friend told me, that his RB250GS was stop working after few days. My Network-Setup: HP ProCurve 1700-8G PORTS | | | | | | | | 1 2 3 4 5 6 7 8 V1 V1 V2 V2 V2 V2 T2,...

RcRaCk2k

Now i am really confused. I've tested to input the value 1250000 in the input-field but the last zero was not taken. So the input-field was only 125000. Today, it was working. I don't know why ;) Wishlist for Bandwidth-Limitation: * Accept values 128k, 6M, 12M, 20M (kBit, MBit) * Set field-size to 8...

RcRaCk2k

Hi all! How can i limit a port to 10 MBit down and 1 MBit up? The wiki told me that the values in egress & ingress are in bps (so i think bytes per second?) but i am not able to add so high values to the Input-Field. 10 MBit = 10 * 1000 * 1000 / 8 = 1.250.000 bps But i am only able to write 125....

RcRaCk2k

Because the MikroTik SXT G-5HnD offers Gigabit Ethernet and was sold with 200 MBits real TCP throughput declaration. SXT 5HnD is a low cost, high speed 5GHz wireless device. Dual polarization 802.11n and Nv2 TDMA technology help to achieve even 200Mbit real throughput speed http://www.mikrotik-shop....

RcRaCk2k

I have the same problem! running SwOS 1.6 and can see DHCP-Discoverys (255.255.255.255 ff:ff:ff:ff:ff:ff) on VLAN2 from a client that is connected to VLAN1 on the same RB250GS Switch. /---------------------------\ | SWITCH RB250GS 5-Port | | Ports | | 1 2 3 4 5 | \---------------------------/ | | | ...

RcRaCk2k

+1 will love this feature!

RcRaCk2k

Yes. CCQ was bad but now it is at 98%. NV2 was enabled all the time. Also NStream is enabled as seen in other howto. I've spent lot of time to understand how MikroTik Hardware is working, and spent a lot of in HowTos also. This is my configuration on the "Station Bridge" side: http://dl.dr...

RcRaCk2k

Dear MikroTik Users! I am very new to the MikroTik Hardware. I switched from UBNT NanoBridges M5 22dBi to MikroTik SXT G-5HnD and have some questions about latency. Before i switched from UBNT to MikroTik, my ping was between 1.2ms and 2.5ms with AirMAX (TDMA) enabled. To setup both MikroTik SXT G-5...

Search found 53 matches