Community discussions

Search found 81 matches

by UpRunTech
Sat Oct 05, 2019 2:28 am
Forum: General
Topic: CAP AC Post Firmware Update Issues
Replies: 5
Views: 1079

Re: CAP AC Post Firmware Update Issues

Apologies for my misrepresentation. To clarify, I am flattening the config every time. The NetInstall part of this is not the issue. The issue is that after any SOFTWARE upgrade I am having to then reset the CAP using NetInstall as it sits in a reboot loop. When not updating, the CAP reboots withou...
by UpRunTech
Sat Oct 05, 2019 2:20 am
Forum: RouterBOARD hardware
Topic: Does CRS328-24P-4S+RM support 24v passive poe?
Replies: 17
Views: 2742

Re: Does CRS328-24P-4S+RM support 24v passive poe?

I installed some of these CRS328's on a site that already had wAPACs. They OVERHEATED and crashed a lot on 802.3af/at I have 4 wAP ac units powered by CRS328-24P-4S+RM which have been running just fine for months already. As of this writing the uptime of all the units is over 82 days, and the switc...
by UpRunTech
Fri Oct 04, 2019 1:57 pm
Forum: RouterBOARD hardware
Topic: Does CRS328-24P-4S+RM support 24v passive poe?
Replies: 17
Views: 2742

Re: Does CRS328-24P-4S+RM support 24v passive poe?

They OVERHEATED and crashed a lot on 802.3af/at and luckily when I switched to 24V they behaved normally again. I guess because of higher voltage.. But they crashed ? Yes. They'd run for a while then lock up tighter than a duck's cloaca. There was no relief until the voltage was dropped. They had b...
by UpRunTech
Fri Oct 04, 2019 12:58 pm
Forum: RouterBOARD hardware
Topic: RB4011
Replies: 371
Views: 70574

Re: RB4011

TL;DR RB4011 is really capable router and my friend uses it for 10G inter VLAN routing with CRS317. It pulls off 10G without a sweat in most scenarios (except large scale with thousands of tiny connections). I agree the RB4011 has lots of grunt. I have just set up a site with 17 CAPACs and am using...
by UpRunTech
Fri Oct 04, 2019 12:51 pm
Forum: RouterBOARD hardware
Topic: Does CRS328-24P-4S+RM support 24v passive poe?
Replies: 17
Views: 2742

Re: Does CRS328-24P-4S+RM support 24v passive poe?

I am glad it has this feature. I installed some of these CRS328's on a site that already had wAPACs. They OVERHEATED and crashed a lot on 802.3af/at and luckily when I switched to 24V they behaved normally again. Another site has wAPACs with a HP 802.3af/at switch and they don't carry on like that. ...
by UpRunTech
Sat Sep 28, 2019 1:16 am
Forum: Wireless Networking
Topic: [SOLVED] WMM giving terrible throughput
Replies: 8
Views: 1523

Re: [SOLVED] WMM giving terrible throughput

Are you using capsman? Do capsman interfaces honor ampdu settings on the cap? Unless I am blind there are no AMPDU settings in CAPSMAN! (https://wiki.mikrotik.com/wiki/Manual:CAPsMAN) Mikrotik employees : what is the default setting in CAPSMAN? Just 0? Is there any aggregation at all? Can you add i...
by UpRunTech
Fri Sep 27, 2019 5:29 am
Forum: Wireless Networking
Topic: Mikrotik wi-fi and Iphone = problem
Replies: 69
Views: 45232

Re: Mikrotik wi-fi and Iphone = problem

Using all the recommended, in this and other threads, "tips and tricks", brought me to a point where wifi was finally working on Iphone X but not anymore on Galaxy S6. Thing was STP instead of RSTP in bridge config (for Iphone). For most if not all small Mikrotik setups no devices need any kind of ...
by UpRunTech
Fri Sep 27, 2019 2:51 am
Forum: RouterBOARD hardware
Topic: RB4011: wlan1 disabling itself
Replies: 260
Views: 33798

Re: RB4011: wlan1 disabling itself

I'd say perhaps there are clients out there that don't work well using anything other than Ce or Ceee. Options like eCee or eC or eeeeCeee are there so the radio can find a clear 20MHz space for C and optionally use the e's depending on the radio interference environment. For 5GHz indoors this shoul...
by UpRunTech
Thu Sep 26, 2019 2:41 pm
Forum: RouterBOARD hardware
Topic: RB4011: wlan1 disabling itself
Replies: 260
Views: 33798

Re: RB4011: wlan1 disabling itself

As the original poster of this thread, I can also confirm this isn’t fixed yet. I might not have posted a lot, but I’ve certainly kept up with all the comments made in this thread. I currently do not have a problem with 5GHz WiFi in the RB4011, but a cAP Gi-5acD2nD provisioned via capsman currently...
by UpRunTech
Thu Sep 26, 2019 2:13 pm
Forum: Wireless Networking
Topic: 802.11r/k, Band Steering
Replies: 17
Views: 2589

Re: 802.11r/k, Band Steering

https://support.apple.com/en-au/HT202628 802.11r/k/v sounds perfect for use with CAPSMan. Mind you, I haven't had issues with roaming on my larger (10+) CAPSMan sites. Using 5GHz only or predominantly, keeping the power low (20dBm) and manually assigning adjacent frequencies helps a lot. To assign a...
by UpRunTech
Thu Sep 26, 2019 2:12 am
Forum: RouterBOARD hardware
Topic: CRS328 Lock Ups
Replies: 9
Views: 1407

Re: CRS328 Lock Ups

I had some VLAN priority rules - they look like the below. At Mikrotik's suggestion I disabled them and now the CPU stays online. The tricky thing was the problem only manifested itself after about 8 hours. I am using VLAN filtering too. /interface ethernet switch rule add disabled=yes new-vlan-prio...
by UpRunTech
Sun Sep 22, 2019 2:41 am
Forum: RouterBOARD hardware
Topic: CRS328 Lock Ups
Replies: 9
Views: 1407

Re: CRS328 Lock Ups

I am seeing theme same symptoms on a new CRS328 with an uncomplicated configuration on 6.45.6. I am able to log in via the serial port and it is still running but it looks like the CPU stops talking to any of the network interfaces so ND, MAC Winbox and DHCP clients no longer work. I made some supou...
by UpRunTech
Sat Sep 21, 2019 6:18 am
Forum: General
Topic: VLAN filtering and more than one bridge
Replies: 4
Views: 631

Re: VLAN filtering and more than one bridge

Right. I figure that apart from the CRS3xx switches that can do VLAN filtering in hardware mode every other device has to do it in software (unless you can manually configure the switch chip in the Switch menu) - so you can set up VLANs any way you like - to use or not use the VLAN filtering either ...
by UpRunTech
Fri Sep 20, 2019 3:18 pm
Forum: General
Topic: VLAN filtering and more than one bridge
Replies: 4
Views: 631

VLAN filtering and more than one bridge

The Bridge Wiki doesn't mention anything one way or the other with VLAN filtering and using more than one bridge.

Can a router have some tagged and untagged ports on one bridge and some other tagged and untagged ports on the other?
by UpRunTech
Fri Sep 13, 2019 1:07 am
Forum: Wireless Networking
Topic: what is the optimum wireless configuration?
Replies: 8
Views: 1260

Re: what is the optimum wireless configuration?

Have a look at this MUM presentation on improving Wifi speeds. Limiting the available rates can help.

https://mum.mikrotik.com/presentations/ ... 286214.pdf
by UpRunTech
Wed Jul 31, 2019 2:32 pm
Forum: RouterBOARD hardware
Topic: Quectel EP06-E and wAP R ac (RBwAPGR-5HacD2HnD)
Replies: 8
Views: 1518

Re: Quectel EP06-E and wAP R ac (RBwAPGR-5HacD2HnD)

I have had luck with the Telit LE910C1-AP (Asia-Pac) which supports B28 too. It has RCM compliance and supports PPP which I have had working with the Mikrotik wAP-R. I have tried the other interface modes like RMNet, RNdis, MBIM and CDC-ECM but they don't seem to elicit a response - we'll have to wa...
by UpRunTech
Wed May 29, 2019 10:59 am
Forum: General
Topic: Tip on using PCQ for low bandwidth links
Replies: 0
Views: 184

Tip on using PCQ for low bandwidth links

I have been stuck on a crummy ADSL2 service that has a crummy inconsistent 5-10Mbit down 1Mbit up speed for a long time. A quick read of how FQ-codel works with dynamically monitoring and adjusting internal buffer parameters got me wondering how buffer size adjustment with a feedback loop somehow co...
by UpRunTech
Sat Apr 13, 2019 1:25 am
Forum: Wireless Networking
Topic: WiFi in garden - wouldn't cAP AC be better than wAP AC?
Replies: 15
Views: 1314

Re: WiFi in garden - wouldn't cAP AC be better than wAP AC?

I will be setting up a CAPAC outdoors soon too in a carport. It will be under a roof line so won't get rain on it. A WAPAC would be fine but I need the CAPAC's PoE out to power an SXTq above it on a mast. My solution to keeping dust and bugs out is to use the square cover and once the cables are att...
by UpRunTech
Sat Apr 13, 2019 12:38 am
Forum: Wireless Networking
Topic: Cap AC, Hap AC2 or UniFi?
Replies: 38
Views: 10392

Re: Cap AC, Hap AC2 or UniFi?

As a rule you should always consider using 5GHz access points per void - be it a room in a house, classroom or office. Try and make sure as much as possible that there is a direct line of sight from the AP to the device (so get the AP up as high as you can), don't rely on reflections or penetration ...
by UpRunTech
Mon Feb 25, 2019 8:44 pm
Forum: General
Topic: Socat like proxy
Replies: 1
Views: 887

Re: Socat like proxy

I had a similar problem the other day, looking for socat-like behaviour. I had a server on a LAN that only binds to the local subnet but had a client application that needs to connect in from the WAN - essentially the packets had to look like they were coming from the router's LAN address, not a WAN...
by UpRunTech
Tue Feb 05, 2019 1:24 pm
Forum: RouterBOARD hardware
Topic: wAP ac overheating?Crashing
Replies: 8
Views: 1457

Re: wAP ac overheating?Crashing

I'm also seeing wAP ac crashing under load (reboot by watchdog timer) - in my case, it's a "NAT router on a stick" (separate tagged VLANs for WAN and LAN sides) and CPU load from sustained high traffic on the wired side only (wireless mostly idle) is sufficient to trigger the issue. Despite reduced...
by UpRunTech
Mon Feb 04, 2019 11:24 am
Forum: RouterBOARD hardware
Topic: wAP ac overheating?Crashing
Replies: 8
Views: 1457

Re: wAP ac overheating?Crashing

Sounds like heat isn't the only problem, my wAP AC is in my house now running at 71C in a room that is 29C. But that is with little load. Mikrotik says it "Tested ambient temperature: -40 to +50C". I have had mine for just under a year this month, only having some though put download problems that ...
by UpRunTech
Thu Dec 27, 2018 10:41 pm
Forum: Wireless Networking
Topic: Google Chromecast
Replies: 4
Views: 990

Re: Google Chromecast

Yep, Chromecast requires station-to-station and/or station-to-node forwarding in order to receive and transmit control messages. You do not need UPnP enabled. Not only Chromecast but anything that using a discovery process like mDNS/Bonjour. For example you'll need client-client on if you want to p...
by UpRunTech
Sat Dec 08, 2018 10:40 pm
Forum: Wireless Networking
Topic: ARM devices and NV2 protocol
Replies: 580
Views: 60347

Re: ARM devices and NV2 protocol

Apparently there is a diagnosis and there are patches in the pipeline.
by UpRunTech
Sun Oct 21, 2018 3:35 am
Forum: Wireless Networking
Topic: What 3rd Party LTE Modems are compatible with the RBwAPR-2nD
Replies: 3
Views: 766

Re: What 3rd Party LTE Modems are compatible with the RBwAPR-2nD

Have a look at the list here: https://wiki.mikrotik.com/wiki/Manual:Peripherals This list will be greatly expanded and improved once ROS7 and it's far far far far newer kernel is used which will mean a lot more native LTE mode compatibility rather than a USB/Serial port mode and PPP being used. A fe...
by UpRunTech
Tue Oct 09, 2018 1:34 am
Forum: Announcements
Topic: v6.43.1 [stable] and v6.43.2 [stable] are released!
Replies: 186
Views: 39140

Re: v6.43.1 [stable] and v6.43.2 [stable] are released!

Seeing as 6.44 will be a while can you please put any wireless patches from 6.44RC into the 6.43 branch? I have had CAPAC and HAPAC units stop registering clients on 6.43.2 until they were rebooted even though the interface was running.

*) wireless - improved stability for 802.11ac;
by UpRunTech
Thu Oct 04, 2018 12:28 am
Forum: Wireless Networking
Topic: hap ac achievable wifi speed?
Replies: 28
Views: 2288

Re: hap ac achievable wifi speed?

As a comparison yesterday I had a Macbook Air (v10.13.6) download OSX 10.14 from a local Mac running a cache at over 40MB/s from a WAP-AC (v6.43.2) a few metres away. I'll try again in the next few days with a CAP-AC and report here. This is on a CAPSMAN system with local forwarding. That's probably...
by UpRunTech
Sun Sep 30, 2018 11:45 pm
Forum: General
Topic: 3011UiAS PPPoe Client not connecting - NBN Australia
Replies: 3
Views: 314

Re: 3011UiAS PPPoe Client not connecting - NBN Australia

Try disabling the PPPoE interface, if it still works then your good to go. Disable your PPPoE interface and put a DHCP client on the ethernet interface you are using for the NBN. Some modem/routers - like the Telstra ones - will automatically try PPPoE (given you have put your PPP login in) and DHC...
by UpRunTech
Thu Sep 27, 2018 11:52 pm
Forum: Wireless Networking
Topic: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot
Replies: 7
Views: 821

Re: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot

Set DHCP lease time to 24hrs DHCP lease script add the host IP to a firewall list named "allowedLan" with a 2hr time out. Firewall filter forward chain accept traffic from the src address list=allowedLan Firewall filter forward chain drop traffic from the screen address list!=allowedLan This is onl...
by UpRunTech
Wed Sep 26, 2018 11:43 pm
Forum: Wireless Networking
Topic: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot
Replies: 7
Views: 821

Re: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot

You can use Time under access list rule, never tried it, but should work. That won't work. And the kid control feature as well. They both can only restrict the hour ranges when the client can stay connect, not the total connected time per day. True, there was some ambiguity to the question. Hotspot...
by UpRunTech
Wed Sep 26, 2018 11:36 pm
Forum: Wireless Networking
Topic: Mikrotik wi-fi and Iphone = problem
Replies: 69
Views: 45232

Re: Mikrotik wi-fi and Iphone = problem

u can tray this metode

in interface wlan
at frecuency mode change to regulatory-domain
select country u base
Don't forget that Apple have some advice on the matter.

https://support.apple.com/en-au/HT202068
by UpRunTech
Wed Sep 26, 2018 2:14 pm
Forum: Wireless Networking
Topic: Roaming Help [SOLVED]
Replies: 5
Views: 449

Re: Roaming Help [SOLVED]

I'd suggest using CAPSMAN with local forwarding and client to client forwarding on rather than 3 lone APs. You can thank me later. Ive not used CAPSMAN before is there any good cases studies \ documentation for it? There's the Wiki of course: https://wiki.mikrotik.com/wiki/Manual:CAPsMAN and loads ...
by UpRunTech
Wed Sep 26, 2018 1:57 pm
Forum: Wireless Networking
Topic: Roaming Help [SOLVED]
Replies: 5
Views: 449

Re: Roaming Help [SOLVED]

Try dialing back the transmit power rather than kicking off users below a certain limit.

Seeing as you have 3 APs I'd suggest using CAPSMAN with local forwarding and client to client forwarding on rather than 3 lone APs.

You can thank me later.
by UpRunTech
Tue Sep 25, 2018 10:11 pm
Forum: Wireless Networking
Topic: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot
Replies: 7
Views: 821

Re: How can I enable a device to connect wifi for only 2 hours per day without setting hotspot

as subject. Thanks

Static IP of the device has been set (i.e. 192.168.88.20)
Use Kid Control. It's not very well named as it actually drives them crazy and out of control.

https://wiki.mikrotik.com/wiki/Manual:Kid-control
by UpRunTech
Tue Sep 25, 2018 4:34 am
Forum: Wireless Networking
Topic: Chromecast weird behavior
Replies: 4
Views: 785

Re: Chromecast weird behavior

i have the same problem.. its work perfectly whit other router, but dont work on mikrotik.. i dont know whats happens!! I have never had issues with Chromecast (Gen1 and Gen2) on Mikrotik at 20MHz and 802.11b/g/n. I have a motel with over 20 Chromecasts all happily talking to Mikrotik. The only thi...
by UpRunTech
Tue Sep 25, 2018 2:43 am
Forum: Wireless Networking
Topic: Capsman client to client forwarding in local forwarding mode [SOLVED]
Replies: 6
Views: 3361

Re: Capsman client to client forwarding in local forwarding mode [SOLVED]

I use Radius VLAN tagging with Capsman, might affect it somehow. Mikrotik-Wireless-VLANID 333 Mikrotik-Wireless-VLANID-type 0 It's *really* unclear in the manual but set Multicast Helper to Full when using multiple VLANs or VLAN override from one SSID. https://wiki.mikrotik.com/wiki/Manual:Interfac...
by UpRunTech
Fri Sep 21, 2018 10:47 pm
Forum: General
Topic: Why isn't WMM Support default?
Replies: 12
Views: 5186

Re: Why isn't WMM Support default?

So, MikroTik: PLEASE implement some option at the wlan level to allow WMM to operate from DSCP, as the other manufacturers have done years ago. It is nice when there can be some override via mangle but it should not be the only option as it incurs manual configuration and CPU loading. Remember that...
by UpRunTech
Fri Sep 21, 2018 10:38 pm
Forum: Wireless Networking
Topic: CAPsMAN & Sonos
Replies: 1
Views: 831

Re: CAPsMAN & Sonos

I wish this wasn't the default, but I am told it's the default because CAPsMAN is first and foremost an "Enterprise product". For most home networks and small businesses you'll also want to enable local forwarding as well as client-to-client which would be the default case of something like a gener...
by UpRunTech
Tue Sep 11, 2018 3:18 am
Forum: Announcements
Topic: v6.43 [current] is released!
Replies: 148
Views: 28867

Re: v6.43 [current] is released!

Hardware accelerated IPsec for 3011 is not included in this release. Unfortunately, we could not get it working stable enough in time. It will be available in 6.44. Is this a driver you guys had to wrote from scratch? I am surprised it's taken so long but I still appreciate that it's coming. I don'...
by UpRunTech
Sat Sep 08, 2018 2:54 am
Forum: General
Topic: iPhone tethering to Mikrotik?
Replies: 12
Views: 5449

Re: iPhone tethering to Mikrotik?

As a gedankenexperiment I'd try this one of two ways. Connect the Mikrotik as a station to the iPhone and then off the same bridge set up an AP slave interface using the same or different SSID. The iPhone might not care about this arrangement. You could also make the AP as a master or the station as...
by UpRunTech
Tue Sep 04, 2018 11:50 pm
Forum: Wireless Networking
Topic: Mikrotik CAP AC Performance Review
Replies: 45
Views: 18907

Re: Mikrotik CAP AC Performance Review

Our clients are buying this CAP AC like crazy. They love it. One client reported to have 48 connections and everyone still achieving speeds of 95mbps plus of which some even got 169mbps on a 200mbps down and 200mbps up fiber line. I am trialling some CAPAC's in classrooms where there are 30+ iPads ...
by UpRunTech
Sat Sep 01, 2018 1:47 am
Forum: RouterBOARD hardware
Topic: RB4011
Replies: 371
Views: 70574

Re: RB4011

I'm personally quite disappointed with lack of LCD and USB. At work I have 2 locations where a 4G stick is plugged in the USB port to serve as a backup link in case the main (VDSL) fails. It is not working well in all router models, though. The power consumption of these sticks is near the limit an...
by UpRunTech
Thu Aug 30, 2018 7:52 am
Forum: General
Topic: Netinstall doesn't work Windows 7 64 bits
Replies: 28
Views: 11198

Re: Netinstall doesn't work Windows 7 64 bits

But when the firewall is switched off... how would that matter?? Sent from my Redmi Note 5 using Tapatalk I tried with the firewall off too but it didn't work either. You tell me! Until I removed all the existing netinstalls in the firewall and reran it with Public permission (in your case you need...
by UpRunTech
Thu Aug 30, 2018 6:03 am
Forum: General
Topic: Netinstall doesn't work Windows 7 64 bits
Replies: 28
Views: 11198

Re: Netinstall doesn't work Windows 7 64 bits

Besides suggesting to run it as administrator, nope. Are you getting any errors when running the command in PS? If so, what are these? Maybe time to reinstall Windows :-) I had similar issues the other day with Netinstall in Windows 8.1 which stubbornly seems to want to put my laptop's ethernet sta...
by UpRunTech
Mon Aug 27, 2018 6:47 am
Forum: Wireless Networking
Topic: How to filter wifi traffic between AP stations on firewall? [SOLVED]
Replies: 6
Views: 1078

Re: How to filter wifi traffic between AP stations on firewall? [SOLVED]

How does your /32 solution go with broadcasts like Bonjour and mDNS? A while back I was looking for a way to force all station traffic on a WLAN interface through a bridge interface so bridge level firewalling could be done. Unfortunately it can't with Mikrotik unless they implement a hairpin functi...
by UpRunTech
Mon Aug 20, 2018 1:54 pm
Forum: Announcements
Topic: v6.42.7 [current] is released!
Replies: 159
Views: 30960

Re: v6.42.7 [current] is released!

upgraded RB751-2HnD and RB2011UiAS-2HnD no dramas. I'll be interested in removing the PMKID and see what happens.

edit: removed PMKID and still here so who needs PMKID anyway?
by UpRunTech
Thu Aug 16, 2018 5:33 am
Forum: Wireless Networking
Topic: Wireless settings not affected by CAPSMAN - which ones?
Replies: 0
Views: 305

Wireless settings not affected by CAPSMAN - which ones?

Hey Normis,

Which wireless settings, if any, can you set and adjust on a WLAN interface that will still affect the interface even if CAPSMAN controls it? For instance how about:

* Antenna gain
* Frequency mode
* Adaptive noise immunity
* Preamble

Can you document these on the CAPSMAN wiki?
by UpRunTech
Tue Aug 14, 2018 5:35 am
Forum: Wireless Networking
Topic: aid for reboot for firmware and version upgrade
Replies: 5
Views: 551

Re: aid for reboot for firmware and version upgrade

Yeah, it's in 6.42.6 (maybe earlier) available from the command line.
system routerboard settings set auto-upgrade=yes
by UpRunTech
Tue Aug 14, 2018 4:09 am
Forum: Wireless Networking
Topic: Caps selecting same channel
Replies: 31
Views: 7290

Re: Caps selecting same channel

Just updated to 6.42.6, nothing has changed. AC radios are still selecting the same channel, this is quite annoying. I wish it was possible to just manually select my own channels in capsman, punt some radios off to a preferred channel. Yes I had 10 CAPs all select the same 2 channels last week (no...
by UpRunTech
Sun Aug 12, 2018 1:26 am
Forum: Wireless Networking
Topic: Understanding 5GHz channels
Replies: 0
Views: 648

Understanding 5GHz channels

I happened across this nice article last week when looking for some information on 5GHz channels. It should clear up any misunderstandings you may have about channel allocations and bandwidth too. It uses Mikrotik channel nomenclature (eg Ceee). Don't rely on Mikrotik's 'auto' channel selection, you...
by UpRunTech
Sat Jul 21, 2018 2:37 pm
Forum: Wireless Networking
Topic: RB2011UiAS-2HnD - poor wireless performance
Replies: 6
Views: 1652

Re: RB2011UiAS-2HnD - poor wireless performance

What operating system are you using? I predominantly use Linux on my laptop that has a "Broadcom Corporation BCM4352 802.11ac" adapter in it. At 2.4GHz on Linux it's driver performance is woeful (but this is known), even with the slight speed improvement that resulted from the latest driver updates ...
by UpRunTech
Sun Jul 15, 2018 2:19 am
Forum: Wireless Networking
Topic: Simplest way to isolate WiFi users? [SOLVED]
Replies: 3
Views: 748

Re: Simplest way to isolate WiFi users? [SOLVED]

Disabling default forward will work only on each AP. Wireless devices on different APs will still be able to see each other. The solution here is to use CAPSMAN with local forwarding and default forward disabled. That way there is only one logical bridge on the Wifi network and you can then use some...
by UpRunTech
Sat May 05, 2018 12:50 am
Forum: Wireless Networking
Topic: capsman to replace cisco
Replies: 1
Views: 400

Re: capsman to replace cisco

No, CAPSMAN will only manage Mikrotik devices as it's a proprietary Mikrotik protocol.
by UpRunTech
Mon Apr 23, 2018 5:08 pm
Forum: Wireless Networking
Topic: Xiaomi phone low Wifi TX rate [SOLVED]
Replies: 112
Views: 26747

Re: Xiaomi phone low Wifi TX rate [SOLVED]

The bonus with 6.42.1 is that it has the BCM Wifi fix in it. Already I am seeing all my Android devices and laptops with BCM chips now connecting faster than 54Mbit! Wooohooo! File transfers over SMB/CIFS to the laptops improved 50% too (on a 20MHz channel).
by UpRunTech
Sun Apr 22, 2018 1:09 am
Forum: Wireless Networking
Topic: Ce Vs eC
Replies: 5
Views: 13714

Re: Ce Vs eC

Did you actually observe this kind of behaviour? I'd expect that any capable client would adapt to whatever wide-channel strategy AP is using. Just as clients adapt to (basic) channel selection. I have had trouble with iPads not connecting to WAP's if I left the control channel set to Auto, so CAPS...
by UpRunTech
Sat Apr 21, 2018 4:21 am
Forum: Wireless Networking
Topic: Xiaomi phone low Wifi TX rate [SOLVED]
Replies: 112
Views: 26747

Re: Xiaomi phone low Wifi TX rate [SOLVED]

6.43rc3 *) wireless - improved compatibility with BCM chipset devices; This includes XIAOMI devices. Please upgrade and test - fixes soon will be included in current releases as well I am pretty interested to know what the fix was. Any chance of a technical summary about what had to get changed? Al...
by UpRunTech
Sun Mar 18, 2018 8:18 am
Forum: Wireless Networking
Topic: CAPs devices working as independent from CAPsMAN as possible
Replies: 5
Views: 810

Re: CAPs devices working as independent from CAPsMAN as possible

This persistent mode would be good ONLY for CAPSMAN client configurations for local forwarding enabled and maybe be able to select an expiry period that would cope with your dropouts. I think it'd be better though to nail down why your CAPSMAN link keeps dropping out. I have found in the past that r...
by UpRunTech
Sat Mar 03, 2018 9:37 pm
Forum: Wireless Networking
Topic: Xiaomi phone low Wifi TX rate [SOLVED]
Replies: 112
Views: 26747

Re: Xiaomi phone low Wifi TX rate [SOLVED]

Hello, we will work on this problem but first we need to finetune the new wireless driver for the new hardware and then we would try to implement the fix for the old wireless hardware. Best regards, Uldis C. Uldis/Normis: When you do your development and testing on Wifi modes do you validate the si...
by UpRunTech
Fri Feb 16, 2018 11:33 pm
Forum: Announcements
Topic: v6.42rc [release candidate] is released!
Replies: 538
Views: 97306

Re: v6.42rc [release candidate] is released!

Derp, well that's good. I am definitely mangling packets with prio. from high 3 DSCP bits to make sure Airplay works as well as possible with WMM. Still I wonder, will this help IOS units too or do they not have this problem? When did the bug get introduced or was it always there?
by UpRunTech
Fri Feb 16, 2018 10:12 pm
Forum: Announcements
Topic: v6.42rc [release candidate] is released!
Replies: 538
Views: 97306

Re: v6.42rc [release candidate] is released!

*) wireless - fixed incompatibility with macOS clients


What was fixed or improved here? Will this also improve IOS clients? I have some sites with a lot of Macbook Airs and iPads so am keen to know,
by UpRunTech
Sat Jan 06, 2018 3:48 am
Forum: Wireless Networking
Topic: iPhones dropping wifi (CAPsMAN)
Replies: 30
Views: 8877

Re: iPhones dropping wifi (CAPsMAN)

Follow this advice from Apple and then get back to this forum list.

https://support.apple.com/en-au/HT202068

And also in on Mikrotik's Wifi settings and in Capsman set enable WMM and set Multicast helper to Full.
by UpRunTech
Sat Aug 12, 2017 12:06 am
Forum: Wireless Networking
Topic: Bridge filtering client to client comms
Replies: 1
Views: 240

Re: Bridge filtering client to client comms

Aw bugger. Looks like I need bridge hairpin which Mikrotik doesn't allow to be enabled or it's hidden somehow. I am not the only one with this problem. Mikrotik please add this option in! Client to client filtering on a bridge is needed! https://forum.mikrotik.com/viewtopic.php?t=79006#p575595 So I ...
by UpRunTech
Thu Aug 10, 2017 7:20 am
Forum: Wireless Networking
Topic: Bridge filtering client to client comms
Replies: 1
Views: 240

Bridge filtering client to client comms

I am trying to set up a bridge filter for client to client comms on a common WLAN interface. I am not having much luck. WLAN and ETH are ports on a common bridge. Bridge Fast Path is off. Default forward on - one client can ping another. Default forward off - the clients can't ping each other. With ...
by UpRunTech
Fri Jul 28, 2017 5:18 pm
Forum: Wireless Networking
Topic: Effective WMM Mangling Rules
Replies: 3
Views: 899

Re: Effective WMM Mangling Rules

I understand now - the best rule to use the one with DSCP bits, that way all traffic will get promoted to the appropriate WMM queue whether it comes in on WLAN or ETH. The ingress case I was thinking that it would preserve WMM priority of incoming packets in cases of client-to-client on the same AP ...
by UpRunTech
Fri Jul 28, 2017 12:22 am
Forum: Wireless Networking
Topic: Effective WMM Mangling Rules
Replies: 3
Views: 899

Effective WMM Mangling Rules

The WMM Wiki entry is a good start but I'll be kind and say whoever wrote it clearly didn't finish it. It's pretty clear to me now that if you want good performance with Mikrotik and CAPSMAN in an organisation with way more mobile and portable devices than plugged-into-a-gigabit-eth devices you prob...
by UpRunTech
Thu Jul 27, 2017 11:43 pm
Forum: General
Topic: IPv6 mangle - set priority
Replies: 9
Views: 1603

Re: IPv6 mangle - set priority

Set priority is not only useful for NV2: - It is used to apply MPLS experimental bits for MPLS QoS - It is used to apply VLAN priority for other vendor wireless systems that use VLAN priority for QoS - Set priority from DSCP high order bits option allows you to handle all 64 DSCP values in QoS with...
by UpRunTech
Thu Jul 20, 2017 3:16 pm
Forum: Wireless Networking
Topic: CAPsMAN wireless network issues
Replies: 6
Views: 3585

Re: CAPsMAN wireless network issues

I have a couple of sites with CAPSMAN, 6 WAPACs each and a lot (100+) of iPads and Macbook Airs. It's a basic network setup. I am having a hell of a time with one of the networks. One SSID Full multicast helper Both types of preamble and guard intervals Local and client to client forwarding ROS 6.39...
by UpRunTech
Tue Jun 27, 2017 6:34 am
Forum: Announcements
Topic: v6.40rc [release candidate] is released!
Replies: 231
Views: 45792

Re: v6.40rc [release candidate] is released!

For this to work, there are two solutions : - the radio clock need to have an input for a sync reference, and a sync generator is needed to generate the sync carrier on the right frequency. - the radio clock need a VCO clock, voltage controlled oscillator, so that it is possible to adjust the trans...
by UpRunTech
Fri Jun 16, 2017 5:42 pm
Forum: Announcements
Topic: v6.40rc [release candidate] is released!
Replies: 231
Views: 45792

Re: v6.40rc [release candidate] is released!

We could think how to sync the APs that are on different frequencies but located on the same tower and connected to the same ethernet network. You could take some ideas from or use PTP (https://en.wikipedia.org/wiki/Precision_Time_Protocol) to synchronise the APs internal clocks over ethernet and h...
by UpRunTech
Fri Dec 04, 2015 11:13 pm
Forum: Wireless Networking
Topic: Multiple VLan's across a PtP Wireless Link
Replies: 9
Views: 3165

Re: Multiple VLan's across a PtP Wireless Link

You can transport VLANs over NV2 using an EOIP interface. ETH-(bridge)->EOIP-(IP)->NV2 ~~ / ~~ NV2-(IP)->EOIP-(bridge)->ETH http://wiki.mikrotik.com/wiki/Manual:Interface/EoIP Don't bother encrypting the EOIP link as it's redundant if you are already encrypting NV2. Of course make sure your switch i...
by UpRunTech
Thu Nov 12, 2015 1:49 am
Forum: Wireless Networking
Topic: Setting up AC Link
Replies: 14
Views: 3429

Re: Setting up AC Link

Thanks for the tip. How do you know this about 802.11ac and NV2? Someone else's comment or some un/official announcement from Mikrotik? The AC stuff has been out a year now, surely NV2 on AC would be working really nice by v6.33.

Anyway, I'll try 802.11 next time I am out there.
by UpRunTech
Wed Nov 11, 2015 9:35 am
Forum: Wireless Networking
Topic: Setting up AC Link
Replies: 14
Views: 3429

Re: Setting up AC Link

I too am having issues getting past 100Mbit throughput even with purported 700+ Mbit connections each way, 65dB SNR and -103dB noise floor between 2 buildings only 100m apart. I am using SXT AC units and v6.33. * What radios are you using? * Are you using NV2 or 802.11? * What is your CCQ and SNR? *...
by UpRunTech
Sat Nov 07, 2015 12:04 am
Forum: Wireless Networking
Topic: CapsmanV2 and forwarding modes
Replies: 0
Views: 657

CapsmanV2 and forwarding modes

I have some observations and questions concerning forwarding modes in Capsman V2. I have done some experimenting and I can see by default Capsman will capture all traffic to/from an AP and route them over the common bridge interface in the Manager Forwarding mode. This makes sense if the access poin...
by UpRunTech
Fri Nov 06, 2015 11:32 pm
Forum: Announcements
Topic: 6.33 version released!
Replies: 140
Views: 34217

Re: 6.33 version released!

Given the single stream TCP/IP speed up is in wireless-cm2, if we are not using Capsman v1 should we all start using wireless-cm2 instead of wireless-fp by default?
by UpRunTech
Sat Mar 01, 2014 6:22 am
Forum: Wireless Networking
Topic: RB Metal AP stability
Replies: 26
Views: 11570

Re: RB Metal AP stability

Try v6.10. I am told it has fixes for the 2.4GHz Metal radio disappearing in AP mode. I have 3 of them that do this at the moment.
by UpRunTech
Sat Mar 01, 2014 3:32 am
Forum: RouterBOARD hardware
Topic: Mikrotik Metal 2.4 wihtout wireless
Replies: 27
Views: 7472

Re: Mikrotik Metal 2.4 wihtout wireless

I too had this problem with the 2.4GHz Metals stopping transmitting. I am told v6.10 has a fix in it for this problem. Try it out.
by UpRunTech
Thu May 02, 2013 1:35 am
Forum: Wireless Networking
Topic: Optimal Wireless Settings for home and office
Replies: 0
Views: 857

Optimal Wireless Settings for home and office

I have had an RB751G for about a year and have fiddled with various wireless parameters to get the best throughput with varying degrees of success. It doesn't help that that 2.4GHz spectrum in my neighbourhood is getting quite busy and dynamic. I can't seem to get a good handle on what are the most ...
by UpRunTech
Sun Aug 26, 2012 7:40 am
Forum: General
Topic: [ASK] ping to bridged modem
Replies: 4
Views: 1213

Re: [ASK] ping to bridged modem

I can ping and get to the configuration page on my modem from my LAN even though it's in PPPoE bridged mode. My LAN is 192.168.1.0/24 and the modem is on 192.168.2.254/24. I have set an extra address of 192.168.2.100/24 on the ether1-gateway port of my 751 which the modem is plugged into. The import...
by UpRunTech
Sat Aug 25, 2012 12:30 am
Forum: General
Topic: 951 and 5.20 weirdness
Replies: 0
Views: 278

951 and 5.20 weirdness

I installed a 951 for a customer the other day as a PPPoE router with firmware 5.20. No matter what I did and how many times I factory reset the thing it would only automatically bring up one automatic PPP mangle rule. Other units including another 951 and a 751 have have always brought up two. I ha...
by UpRunTech
Fri Jul 27, 2012 12:20 pm
Forum: General
Topic: 951-2n in reboot loops
Replies: 0
Views: 351

951-2n in reboot loops

I have two 951-2n units running v5.19 and 5.16 each. I have discovered two disturbing bugs. a) Using Winbox Selecting "AP and Client Mode" in the Adaptive Noise Immunity setting and clicking on Apply ends up making the units go into endless reboots with about a 30s period. This happens on 5.19 and 5...