Community discussions

MikroTik App

Search found 11 matches

by jthoele
Wed Dec 02, 2015 5:16 pm
Forum: General
Topic: EOIP Tunnels, only tunnel id = 0 works - Fastpath allows pings (3 - RB953GS-5HnT)
Replies: 7
Views: 2381

Re: EOIP Tunnels, only tunnel id = 0 works - Fastpath allows pings (3 - RB953GS-5HnT)

I found that one of the default firewall rules was blocking traffic on anything other than id=0. disable your firewall rules one by one until you find it. hope that helps
by jthoele
Tue Nov 10, 2015 7:39 pm
Forum: General
Topic: EOIP Tunnels, only tunnel id = 0 works - Fastpath allows pings (3 - RB953GS-5HnT)
Replies: 7
Views: 2381

EOIP Tunnels, only tunnel id = 0 works - Fastpath allows pings (3 - RB953GS-5HnT)

Hello, I am trying to connect two remote sites to a home site using EOIP Tunnels so that they are all on the same L2 network. I have setup an EOIP tunnel between site 1(home) and site 2 using tunnel id = 0 , and site 1 to site 3 is using tunnel id = 1. Site 1 distributes DHCP to remote sites and act...
by jthoele
Tue Jul 07, 2015 9:31 pm
Forum: Announcements
Topic: hAP lite
Replies: 392
Views: 181900

Re: hAP lite

Does the hAP lite support MESH networking? I would like to setup several of these in a mesh sensor network. thanks.
by jthoele
Mon Feb 23, 2015 10:14 pm
Forum: RouterBOARD hardware
Topic: AVAGO HFBR-57E0LZ 1300nm Multi-Mode SFP and CRS212-1G-10S-1S+ IN not quite working
Replies: 2
Views: 1126

AVAGO HFBR-57E0LZ 1300nm Multi-Mode SFP and CRS212-1G-10S-1S+ IN not quite working

Hello, I have been looking for a 1300nm multi-mode sfp module that is compatible with mikrotik routerboards (specifically CRS212... and RB953.. boards). I found an sfp module from AVAGO (HFBR-57E0LZ) that is 1300nm, multi-mode, 100Mb/s fast ethernet capable AV02-2810EN+DS+HFBR-57E0xxZ+20Jan2011 (1)....
by jthoele
Fri Feb 13, 2015 4:28 pm
Forum: RouterBOARD hardware
Topic: SFP not recognized by RB953GS-5HnT
Replies: 3
Views: 1242

Re: SFP not recognized by RB953GS-5HnT

I applied the latest release candidate yesterday. With a Fiber Power level meter, I have noticed that the SFP's will not output any power if they are not recognized at boot up, but the power is there instantaneously if they are. Oddly enough the boards with Routerboot 3.17 seem to be more stable tha...
by jthoele
Wed Feb 11, 2015 9:13 pm
Forum: RouterBOARD hardware
Topic: SFP not recognized by RB953GS-5HnT
Replies: 3
Views: 1242

Re: SFP not recognized by RB953GS-5HnT

I am still having trouble with this Mikrotik support. any suggestions?
by jthoele
Tue Sep 30, 2014 11:15 pm
Forum: RouterBOARD hardware
Topic: SFP not recognized by RB953GS-5HnT
Replies: 3
Views: 1242

SFP not recognized by RB953GS-5HnT

Hello all, I have a test setup with 3 RB953GS-5HnT boards equipped with S-35LC20D and S-53LC20D single strand SFP Modules. I have an issue on reboots where the Routerboard will not initiate the SFP. It shows the Module as present, but does not activate the output or show any of the diagnostic inform...
by jthoele
Tue Sep 16, 2014 4:03 am
Forum: Wireless Networking
Topic: How To: Bridging VLANs over Mikrotik Wireless
Replies: 5
Views: 1644

Re: How To: Bridging VLANs over Mikrotik Wireless

I am looking to do something similar. Similar setup with 3 more hops (from mik 2 to mik3, mik3 to mik4...) with the two vlans accessible at each hop. The connection between each hop would be wireless radios.
by jthoele
Fri Jul 11, 2014 11:45 pm
Forum: Wireless Networking
Topic: Compex WLE350NX link speed 3x3 MIMO limited to 300Mb/s
Replies: 1
Views: 758

Compex WLE350NX link speed 3x3 MIMO limited to 300Mb/s

Can anyone tell me how to enable the higher data rates for this card. I am currently limited to HT40-7 with 3X3. Is there a way to force the card to a higher data rate?

thank you
by jthoele
Wed Jun 11, 2014 9:48 pm
Forum: Wireless Networking
Topic: Trunking between RB493G and Cisco Catalyst switch - vlan 1
Replies: 3
Views: 1562

Re: Trunking between RB493G and Cisco Catalyst switch - vlan

So do I add the trunk port to the vlan 1 bridge? or how will the router know to pass the untagged traffic from the trunk port to my vlan 1 bridge?

thanks again
by jthoele
Fri May 30, 2014 10:41 pm
Forum: Wireless Networking
Topic: Trunking between RB493G and Cisco Catalyst switch - vlan 1
Replies: 3
Views: 1562

Trunking between RB493G and Cisco Catalyst switch - vlan 1

Hello all, I am trying to configure an RB493G as a wireless AP Bridge with 3 separate networks, with port 1 as a trunk, ports 2-5 as vlan 1, ports 6 & 7 as vlan 3, and ports 8 & 9 as vlan 5. I currently have the trunk working for vlans 3 and 5 using bridges to join the ports and wireless cards. Wher...