no error no cisco GigabitEthernet1/0/3 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 2c3e.cfe6.8d03 (bia 2c3e.cfe6.8d03) MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive ...
I checked with RB850 (ether1, ether2 put together with bridge, no vlans, no tagging etc., just plain bridge) Ether1 comes from unmanaged HP, ether2 goes to RB1100. When I connect RB1100 , then they see each other, but traffic from uplink HP on ether1 not work any more, although it doesn't hang up t...
On my RB951G, which features (single) AR8327, the following sets ether2 as hybrid port (trunk with native) ... VLAN 40 is untagged (native) and VLAN 3999 is tagged: /interface ethernet switch port set 1 default-vlan-id=40 vlan-header=always-strip vlan-mode=secure /interface ethernet switch vlan add...
on RB1100 it's opposite, switch2 is 1-5, switch1 is 6-10...
ether1 is UNtagged port
ether5 is tagged
so unfortunately your provided code won't help. That's the main problem, that everything work with tagged port, but can't get it working with the untagged port
Hi, I have stuck with this already few days trying to figure out how to properly set tagged and untagged vlans on RB1100Ahx2. the principle diagram is here as an example: (pink is for testing, both cable ar not connected at the same cable) rb1100ahx2.jpg Cisco 1/0/3 UNtagged is connected to ether1 -...
btw, I remember that some time ago (maybe last few months, maybe earlier) Proximus sent some kind of e-mail regarding Smart wifi, that they are changing something... but can't find it now, probably I have deleted it (as it's not the monthly bill :)) That was SMS :) Dear Proximus customer, final rem...
Hi, I was using it for few months as temporary solution until Proximus installed permanent DSL connection. The router now is used for other purpose, so I don't have that config, neither have ability to test it. Probably they have changed something on their side. Does it work from laptop? (so to be s...
Does this thread help, involving these properties? Thank's, this helped a lot. If anyone needs, here is the Mikrotik config export for Belgium Proximus Smart WI-FI: /ip dhcp-client add dhcp-options=hostname,clientid disabled=no interface=wlan2ghz /interface wireless security-profiles add authentica...
First connect by laptop and login with username and password. Then change your Mikrotik wlan1 MAC to your laptop MAC. And then try to connect your Mikrotik as client to the wifi network. sorry, but this does not sound seriously. p.s. changic MAC address (as well IMEI for mobile phones) is forbidden...
I need to connect to a wifi network from Mikrotik as client. This has not been a problem previously (with WPA2 Pre Shared Key), but this time the network is asking for user+password of 8 characters. How can I define that in MT? Capture.JPG https://www.proximus.be/support/en/id_sfaqr_hot_connect/pers...
I have home network configuration as shown below. I have configured RB250GS , made trunk ports to RB951 (main router). But i have stoped getting further in configuring VLAN switching in RB951. if i create a vlan with id 3 on eth3,i can set vlan with id 3 on eth4 (but it has different name), so after...
I recommend remove address from routerboard interface and go to lower layers: 1 VLAN from pc client to router, and for more security, static ip as link, same as pppoe 2 PPPoE from pc with username and passwd to access 1. Your idea is to set up static ips for computers? if so, it will take a long ti...
I wan't to limit access for unknown computers in my network. I have set up eth-lan with arp: reply only; set up dhcp with pool: static only, made some static ARP addresses. From this point - no one can get dhcp, so can't get any kind of network with just plugging in cable. But if someone put in stat...
you have a good feature of status != connected. i will try to implement it. here's mine script: /tool netwatch add down-script=":local i 0; {:do {:set i (\$i + 1)} while ((\$i < 5) && ([/ping 159.x.x.x interval=3 count=1]=0))};\r\ \n:if (\$i=5) do={:log info \"3G modem restart\&quo...
I've got two 3G USB modems for internet. I also got two RB751 devices. I wan't to have both 3G modems working (connected) and do failover from one to another (if first link drops). I tried to add both USB 3G modems to one router via USB HUB, they worked, but they could not be both active. If one dia...