MikroTik

DaxStox

Hi guys, Im tring the new FW on RB411U with MC7710 Sierra Wiereless modem and 4G SIM (but the serice 4G is not yet enable by ISP) and I notice settng 3G + LTE the interface LTE doesnt connect. Resuming: Using GSM + 3G + LTE the interface connect on 3G (is OK). Using 3G only the interface connect (is...

DaxStox

I am using ROS 6.34.1 on RB411U with MC7710 and the AT command GRESET generate a timeout failure. THE COMMAND IS interface lte info 0 user-command="AT!GRESET" user-command-only=yes THE ANSWER IS: failure: Info or scan not running! action timed out - try again, if error continues contact Mi...

DaxStox

lte - improved dhcp handling on interfaces that doesn't support it;

Some more details for this bug FIX, please?

DaxStox

HI, THE CREATION OF SUPOUT.RIF FILE DOSNT WORK FINE. I TRIED SEVERAL TIMES BY USING THE COMMAND MENU "MAKE SUPOUT.RIF" AND THE EFFECT IS THE ROUTER DISCONNECT AND AFTER THE FILE IS NOT GENERATE COMPLETELY, JUST ONLY 24 KB. I wonder how much is CPU load just while supout.rif creating? This...

DaxStox

HI,
THE CREATION OF SUPOUT.RIF FILE DOSNT WORK FINE. I TRIED SEVERAL TIMES BY USING THE COMMAND MENU "MAKE SUPOUT.RIF" AND THE EFFECT IS THE ROUTER DISCONNECT AND AFTER THE FILE IS NOT GENERATE COMPLETELY, JUST ONLY 24 KB.

DIsconnectionDuringCreateSupout.JPG

DaxStox

The AT command can be sent by the following command:

/interface lte info 0 user-command="AT+CFUN=1" user-command-only=yes

or

/interface lte info 0 user-command="AT+CFUN=1"

DaxStox

ANOTHER FAILURE TEST:
USING HYPERTERMINAL AND NETINSTALL 6.27.
ROUTER RB493G + FW 6.27 + BOOTER 3.22
AFTER SYSTEM REBOOT COMMAND FROM WINBOX THIS IS THE RESULT:

627 322 after reboot.JPG

THE ROUTER DOES NOT MORE REBOOT.

DaxStox

IT IS A PROBLEM OF THE BOOTER 3.18 - IS NOT COMPATIBLE WITH RB493G.
THE BOOTER 3.10 WORKS!
IT IS POSSIBLE TO DOWNGRADE TO BOOTER 3.10?
OR WHERE I CAN FIND THE LAST BOOTER 3.22?

DaxStox

I TRIED ROUTER OS 6.27 INSTALLED ON A NEW RB493G FW 5.26 BOOTER 3.18:
1. COPIED 6.27 NPK FILES IN FILES DIR
2. REBOOTED THE ROUTER USING SYSTEM REBOOT COMMAND
THE ROUTER DOES NOT REBOOT !!

DaxStox

HI,

I DID ADDITIONAL TEST WITH RB493G Fw 5.26 booter 3.18: A BOOT TEST WITH MICROSD AND ONE WITHOUT MICROSD.

THE MESSAGE “Boot configuration CRC error” is always present.

BOOT WITHOUT MICROSD:

RB493GBOOTNOMICROSD.JPG

BOOT WITH MICROSD:

RB493GBOOTMicroSD.JPG

DaxStox

ANOTHER FAILURE TEST ON FW 5.26 RB3493G First boot Ok: the router turn on, first beep ok second beep ok Using winbox I changed the boot device from "flash-boot" to "nand-if-fail-then-ethernet", Shutdown the router. Power OFF Power ON First beep OK and stop! The router doesn not ...

DaxStox

The boot device setting is

flash-boot

. It is right or it have to use

nand-if-fail-then-ethernet

?

DaxStox

YES, WITH MICROSD IT WORKS!
But I cannot use microSD, so what it the solution of the problem? It is possible to uninstall the microSD or remove from configuration or .. I don't know.

DaxStox

The support suggest to use a microSD and test the boot but I cannot use a microSD on our line production.
I think the problem is on the BOOT v3.18. The BOOT v 3.10 works as we expect.

DaxStox

I have the same problem on RB493G FW 5.26 Boot 3.18
The router does not boot from console.
B.R.

DaxStox

Hi everyone,

What is the OpenSSH or SSH version used by router mikrotik firmware ?

DaxStox

Hello world, Im using RB493 + 5.19 fw and I have the following weak-point analysis on the SSH protocol: OpenSSH < 3.0.2 Multiple Vulnerabilities OpenSSH < 3.1 Channel Code Off by One Remote Privilege Escalation OpenSSH Kerberos TGT/AFS Token Passing Remote Overflow OpenSSH < 3.4 Multiple Remote Over...

DaxStox

Solved in http://forum.mikrotik.com/viewtopic.php?f=2&t=74043

DaxStox

Solved in http://forum.mikrotik.com/viewtopic.php?f=2&t=74043

DaxStox

Solved in http://forum.mikrotik.com/viewtopic.php?f=2&t=74043

DaxStox

Thanks bysard!

The correct configuration is using data channel=4 and info channel=3. With these values the modem is connected and I can ping the ip 8.8.8.8.

This cfg works also with the modem MC8292!

I can still use my modem init string and other settings.

Great!

DaxStox

Yes, I have. I tried to uncheck and the modem is gone to disconnected status from waiting packets.

DaxStox

Here my solution:
RB411U with 6.4 FW without LTE Interface:

port firmware set ignore-directip-modem=yes

Info Channel = 3
The router can read Info

INFO CHANNEL 3.png

Now I can't connect, no ping google ip 8.8.8.8
I will investigate the SIM, and the modem init string.

Bye.

DaxStox

HI, I CONFIRM WHAT bjorncmtec SAID. I TRIED THE MC7710 WITH FW : SWI9200X_03.00.08.02AP R3715 CARMD-EN-10526 2011/11/14 18:42:43 (SEE FIGURE BELOW) IN RB411U WITH WITH FW 5.25 AND THE PPP INTERFACE CANNOT CONNECT TO THE MODEM (SEE FIGURE BELOW). IN ORDER TO READ THE FW VERSION YOU CAN USE THE LTE IN...

DaxStox

Anyone knows?

DaxStox

Hi everyone,
Is it possible to configure the parameters used in ppp-client in LTE interface ?

AUTHENTICATION : PAP, CHAP, MSCHAP, USER, PASSWORD
DIAL COMMAND
PHONE NUMBER
etc...

How does the LTE Interface works?

DaxStox

I tested the MC8092 with FW 6.1 and it works! Great!
Now my question are :
1. IS IT POSSIBLE TO USE THE MODEM MC8092 AS PPP-CLIENT?

RB411U_6.1 PPP.png

2. HOW CAN I CONFIGURE THE AUTHENTICATION MODE PAP, CHAP, MSCHAP1 & MSCHAP2 IN LTE INTERFACE (User and Password)?

DaxStox

The modem MC8092 in RB411U with FW 5.25 works good (internet navigation works!) using the LTE Interface (is running state): RB411U_5.25.png I cannot use the modem with FW 6.0, the LTE interface doesn't run and I cannot read the information in the LTE Info, the message box says: Couldn't start -Confi...

DaxStox

The modem MC8092 is not 4G LTE.

Ipse dixit.

DaxStox

I have similar problem: RB493 wifi configured as "STATION" Eth1 : IP 10.68.90.171 - GW 16.68.90.201 Wifi: IP 10.159.226.70 - GW 10.159.224.201 via AP. Interface Eth1 is DISCONNECTED and ENABLED: the ping from my PC 10.68.90.253 to IP wifi 10.159.226.70 dosn't work Interface Eth1 is DISCONN...

DaxStox

# jan/ 2/1970 0: 3:53 by RouterOS 5.22 # software id = DR94-6P55 # 00:03:48 async,debug lte0: sent AT+COPS? 00:03:48 async,debug lte0: rcvd +COPS: 0 00:03:48 async,debug lte0: sent AT+CPIN? 00:03:48 async,debug lte0: rcvd +CPIN: READY 00:03:49 async,debug lte0: sent AT+GMI 00:03:49 async,debug lte0...

DaxStox

Ma il router lo vede come interfaccia LTE.

DaxStox

Same problem with MC8775. See my post: RB411U+Sierra Wireless 8775=freez dialing out.. or dialing.. http://forum.mikrotik.com/viewtopic.php?f=2&t=66307 I'm using this logical step: AT+CFUN=1,1 if connection is still ko then AT!GRESET if connection is still ko then DISABLE PPP - REBOOT SW + ENABL...

DaxStox

Scenario: RB411U + FW 5.22 + 4G LTE Card MC8092 (Sierra Wireless)
The LTE Info gives some error (see image belove)
Is the 4G LTE Card MC8092 supported?

DaxStox

Hi everyone, Scenario: RB493 v. 5.19 I use the dns-update command tool to register to a DNS server in a script: /tool dns-update dns-server=$dnsIP ttl=86400 name=$ssname zone=$zoneDomain address=newIP ....somenthing to do after dns-update If the command tool dns-update fail (ex. connection timeout) ...

DaxStox

Thanks a lot for the suggestion, here the log trace: # jan/ 1/2002 2:17:27 by RouterOS 5.19 # software id = DR94-6P55 # 02:00:13 async,ppp,debug,packet <interface-identifier 0:0:0:3> 02:00:13 async,ppp,debug ppp-out1: MPLSCP lowerup 02:00:13 async,ppp,debug ppp-out1: MPLSCP open 02:00:13 async,ppp,d...

DaxStox

Hi people, I am using RB411U fw 5.19 with Sierra Wireless 8775 modem and I have the following bad behavior: The modem is connected with signal strength=-63dBm and I can ping the google ip 8.8.8.8 In the log i have this calling status: 02:00:49 async,ppp,info ppp-out1: dialing... 02:00:50 async,ppp,i...

DaxStox

Another script test via API: I have moved the "once" instruction to the end of the line. Script's code: :log info "TEST MONITOR"; /interface ethernet monitor ether1 do={:log info "ether1 state $status";} once; The output log is : script info TEST MONITOR script info eth...

DaxStox

The output's API is

!re
!re
!re
!re
!re
!re
!re
!re
!re
!re
!trap
!trap=category=0
!trap=category=0=message=no such item
!done
!re
!re
!re
!re
!re
!re
!re
!re
!re
!re
!trap=category=0=message=no such item
!done

DaxStox

I test my own "file.auto.rsc" and it works always after a reboot. I think the file works only the first time after e reboot.

I hope this is useful.

Bye.

DaxStox

Hi people, I am using RB4xx router with 5.19 FW and I use the following script for connection status logging: :log info "MONITOR493"; /interface ethernet monitor ether1 once do={:log info "ether1 state $status";} /interface ethernet monitor ether2 once do={:log info "ether2 ...

Search found 41 matches