Hmm, dug out my old RB751G-2HnD # DEVICE VENDOR NAME SPEED 0 1:1 Linux 3.3.5 ehci_hcd RB400 EHCI 480 Mbps 1 1:2 Huawei Technologies Co., Ltd. HUAWEI Mobile V7R11 480 Mbps Fires up right of the bat, chuck in DHCP client on LTE and I'm off. Using USB to PCI-E adaptor! pin-status: no password required ...

Just downgraded to v6.28 since that's what the Wiki says works - still nothing! # DEVICE VENDOR NAME SPEED 0 2:1 Linux 3.3.5 ohci_hcd RB400 OHCI 12 Mbps 1 1:1 Linux 3.3.5 ehci_hcd RB400 EHCI 480 Mbps

Hi all, Looking for some help! Been using a Sierra Wireless MC7700 in my RB411UAHR, which is good for HSDPA in UK and up to LTE in North America, but no good for LTE in EMEA regions (need MC7710 for that which is not available any more). So logically checked LTE list on Mikrotik wiki - oh good, the ...

Haha, OK so I think I've fixed it. During the set up I realised that I could not ping the router, so I enabled ICMP IPv4 options to 'any' which fixed that problem then caused the issue. If any one can help with what the best setting on that would be to allow ping but not ruin packet flow to correct ...

Hi to you all- looking for some help! Been learning RouterOS for about a year now, I have left mangle till now. What I have is a requirement to have WAN1 routed to ETH1 With it's own subnet on interface. WAN1 routed to ETH2 with it's own subnet on interface. WAN2 routed to ETH4 with it's own subnet ...

Using mangle and routing marks, then adding routing paths for each mark you can force the clan traffic to different wan interfaces. Thanks Trollman, I had a feeling it was something like that. I'm still getting my head around mangle so I'll have a go at programming something. Any idea if all dns re...

Hi to you all. I'm reaching out for a bit of advice. I'm providing a temporary network for a festival. We always have a challenge getting connectivity to random places in a field. So in this instance we will be using several sources. Different clients onsite have different requirements. Low mid and ...

Request- To pull up a no frills terminal window from winbox. Justify- I've been teaching myself RouterOS for a couple of years now and often open up two instances of Winbox. One for terminal and one to see changes. Result- Fewer input strokes to reach terminal through Winbox. Many apologies if I've ...

Any idea where I can buy the QCA9880/9882 rev2?

What antennas are people using?

Many thanks

R

Hi Normis,

Agreed it seems like a NAND issue. This router is in service at an Event. For the moment it's still routing. It's going to be tricky for me to do any servicing to it until after the event is over! Thanks for advice though I'll get in contact with support.

Yes I just observed the usermanager store re-appear

Username and password has reset again! How can this happen?

Hi All, So I've been setting up WiFi for an event in the UK for the last few days now. Literally just left site and the client rings up telling me no one can login through the hotspot. Using CCR1009-8G-1S-1S on RouterOS v6.13 I've got everything connecting to RB450 in office with pptp. So I get in a...

Hi Joe, I've tried a few combinations, as on the CCR there is console on Serial0, firstly i tried Serial1. No joy. So then i disabled the Console on Serial0 and added to that and still no joy. So got to wondering whether it's something to do with the architecture being different. MIPs vs Tile. Or ju...

Apologies if I was not clear, I am using the UPS package in RouterOS to monitor UPS status, via serial only.

Hi, It's pretty basic in that it just has serial connection.

Hi All, looking for the benefit of someone elses superior knowledge :) I am the proud new owner of a CCR1009-8G-1S-1S+ I've also just got an APC SMART-UPS SC 450 For some reason I connect see it in the CCR... I can get to UPS from RB450G just fine and I can get to it from Windows over USB serial ada...

Thanks Steven, they both look interesting. Definitely space to mod them as well. I am planning to utilize the USB port as well for 3G/4G failover, so enough room for 5v adaptor aswell

Hi All, I have been looking all around for a case that could house my project built around an RB493. I work in the events industry and have I am putting this together to be a flexible centre point of a network with different applications. As such I have bought 3 5/2.4 cards some SMA cables and also ...

Hi all, I have been struggling for two days to get my RB2011LN ping out with Vigor 120 attached. Like initial post I could get Vigor 120 alive via windows PPPoE. Went through every thing with a fine comb, everything seemed to check out, PPPoE client shows connected, I even tried my RB450 set up to e...