MikroTik

sch

Check if power sources are correctly connected. 48V PSU to DCIn 48-57V and 24V PSU to 18-28V.

sch

What's new in 7.16 (2024-Sep-20 16:00):

*) container - clear VETH address on container exit and mark interface as running only when VETH is in use;

sch

Please contact MikroTik support and add supout.rif file.

sch

SFP+ DAC cables produce no heat at all, fiber SFP+ modules usually aren't very hot either. It would be nice to have additional SFP+ even with the restriction, no support for copper modules because of power/cooling constraints. Users often use copper SFP+ (S+RJ10) modules in passively cooled devices...

sch

Please contact MikroTik support, and send supout.rif file to support@mikrotik.com

sch

Another newsletter, and still looking some new products in your nifty "half rack, half U" form form factor(RB5009/L009/...) – like a PoE switch or SFP-only RB5xxxx (to interconnect with other RB5009s in a rack). - CRS304 10G Ethernet switch (no modules needed!) That is a nifty device. But...

sch

wiktorbgu and diamuxin please contact MikroTik support and provide supout.rif files.

sch

Do not use the container for full-fledged OS installation.

sch

CCR2004-1G-2XS-PCIE requires a minimum Linux kernel 5.15.25 on your Linux OS.

sch

Please contact MikroTik support and send supout.rif file.

sch

v. 7.15.1
Reboot after 22 hours.
Сpu-temperature 55С.
At what temperature can the device reboot?

should reboot at 105C

sch

Check your container/config, maybe you have set an insufficient amount of ram?

ram-high	RAM usage limit.  ( 0 for unlimited)

sch

7.15beta6
In Proxmox VE VNC shows Starting services...
Unable to access the system.

This has already been fixed and the fix will be included in the next version of RouterOS.

sch

CRS310-1G-5S-4S+ with latest beta firmware 7.15beta4 # NAME VALUE TYPE 0 voltage 23.4 V 1 cpu-temperature 24 C 2 sfp-temperature 43 C 3 fan-state ok 4 fan1-speed 12990 RPM 5 board-temperature1 23 C 6 board-temperature2 16 C 7 psu1-voltage 23.7 V Fan speed is in max rpm even temperature is low. Targ...

sch

> *) x86 - fixed VLAN tagged packet transmit for igb (introduced in v7.12);
Unfortunately this had not been fixed. My VLANs at IGB and x86 not work at all :(

Please contact support and add the supout.rif file from your system.

sch

@fragtion
Could you please clarify if your VPS provider has made any updates?

sch

hAP ac2 does not support high-voltage. You need to power your rb5009 with 24V PSU, or use RBGPOE-CON-HP.
Which converts high-voltage to 24V.

sch

VMware suggests not to upgrade the hardware version unless newer features are required - https://kb.vmware.com/s/article/1003746

Vmware 17.x default hardware version is 21, please change it to 18 and try again.

sch

I'm observing PoE issue with hAP ax2 and SXT LTE6 kit: when ether1 on hAP ax2 is configured with PoE Out = "auto on", PoE seems to be reset (during LTE modem init ?) and SXT LTE6 kit is rebooted. This continues in a loop. SXT LTE6 kit could boot on 6 or 7 iterations successfully. Setting ...

sch

The current implementation of L009 has basic passive PoE (ON or OFF), it doesn't fully support the optional auto-sensing feature for the 'Auto-on' mode.

sch

Please send an email to MikroTik support and include a supout.rif file.

sch

Updated hAP ax3 from 7.11.2 to 7.12rc7 and all VETH interfaces are gone... :(

Please downgrade to v7.11.2, generate a supout file, upgrade to 7.12rc7, generate a new supout and send both files to support@mikrotik.com.

sch

CHR v6 has one partition but CHR v7 has two.

you need to edit the install script part where you mount an image with offset, e.g:

mount -o loop,offset=512 /tmp/chr.img

and change to:

mount -o loop,offset=$((512*65570)) /tmp/chr.img

sch

Check your disk space while deploying your second container.

sch

CHR does not support UEFI.

sch

It will be fixed with a Linux kernel update.

sch

Please monitor system resources while pulling container image. Does router hdd free space not shrink?

sch

Are you using CHR or x86 on bare metal hardware? Has your CHR instance minimum required allocated amount of RAM? The minimum required RAM depends on interface count and CPU count. You can get an approximate number by using the following formula: · RouterOS v6 - RAM = 128 + [ 8 × (CPU_COUNT) × (INTER...

sch

Did you change your CPU type to Default (kvm64)?

sch

By default Quemu Guest agent is disabled, you can enable it in VM options under Quemu Agent.
Note: Default CPU type should be selected Default (in our case it is Default (kvm64)).

sch

Please send supout to support@mikrotik.com.

sch

Please send the supout.rif file from your device to support@mikrotik.com

This article explains how to make a supout.rif file:
https://help.mikrotik.com/docs/display/ROS/Supout.rif

sch

It is a known issue, Snowzach, a user has described a potential solution: viewtopic.php?p=981824#p981824

sch

The KVM package is now unsupported, and it is recommended to use the container feature, which has been supported since RouterOS 7.
https://help.mikrotik.com/docs/display/ROS/Container

sch

Such information can be found on the device specification page. RB5009UG+S+IN https://mikrotik.com/product/rb5009ug_s_in · CPU temperature monitor Yes RB5009UPr+S+IN https://mikrotik.com/product/rb5009upr_s_in · CPU temperature monitor Yes · Current Monitor Yes · PCB temperature monitor Yes · Voltag...

sch

*) x86 - improved igc driver support;
What has included in igc driver?

support for Intel I226 eth controller

sch

All power options support a wide voltage range of 24 – 57 V. However, you can not mix the voltages. If you’re using PoE-out to power other devices, the board will choose the source with the highest voltage (DC jack or the 2-pin connector) to power those. https://i.mt.lv/cdn/product_files/RB5009UPrS...

sch

No, PoE is not isolated, nor is the device's powering (DC-Jack, 2Pin).

sch

CCR2004-1G-12S+2XS - https://i.mt.lv/cdn/product_files/CCR20 ... 200459.png
CCR2004-16G-2S+ - https://i.mt.lv/cdn/product_files/CCR20 ... 210931.png

sch

Yes, this is normal behavior. Depending on the model it can be 1 to 4 IRQ per one fan rotation.

sch

The temperature value is provided by SFP modules. If your device does not have attached SFP modules that can provide temperature values, it won't be shown in health, and you will not be able to use OID .1.3.6.1.4.1.14988.1.1.3.10.0

sch

Did you read product specification? There is no information that this device can be powered by providing current through ground.

sch

Try this link: https://download.mikrotik.com/routeros/ ... 6.44.6.npk

sch

https://www.virustotal.com/gui/file/793 ... /detection

Winbox is fine, that was fluke false-positive

sch

No, you cannot change it. But you can create dozens of virtual ap for both wireless interfaces. https://wiki.mikrotik.com/wiki/Manual:Interface/Wireless#Virtual_interfaces Note: you can create up to 127 virtual interfaces per physical interface. It is not recommended to create more 30, since the per...

sch

Contact you local distributor, and ask them https://mikrotik.com/buy/asia/vietnam

sch

It is leds on the R11e wireless modem, they lit when 2.4Ghz link is established.

sch

What SFP + modules are used, what is their temperature?

sch

Did you read S+RJ10 general guidance?
https://wiki.mikrotik.com/wiki/S%2BRJ10 ... l_guidance

sch

None of these are fake. Why do you think any are fake? Any reason? Yes, MikroTik has many factories now. In many countries. They provide this compare photos to say that china model is fake . so Why the Lithuania model just have a mikrotik adhesive label on back of it and Don't have a hard logo on p...

sch

This is MikroTik user forum. Your question should be asked at Huawei forum.

sch

Contact MikroTik support and send supout.rif file with the latest stable RouterOS version.
https://mikrotik.com/client/support

sch

Please contact MikroTik support by email: support@mikrotik.com, providing supout.rif file from your devices. Also please describe your issue with details (how you are powering your device, etc.)

sch

If an issue still occurs after a firmware upgrade, write to support@mikrotik.com, providing supout.rif files from both devices.

sch

Did you look at this example?
https://wiki.mikrotik.com/wiki/Manual:I ... sec_tunnel

sch

BestVPN is one you make yourself, host CHR somewhere and use native Mikrotik protocols (EoIP, IPIP, etc.) Generally avoid TCP based protocols (SSTP, OpenVPN) for performance reasons (single TCP connection), always prefer UDP ones (PPTP, L2TP,...). Obviously it all depends on what you are trying to do.

sch

hEX PoE can power at/af mode B (4,5+)(7,8-) compatible devices, if 48-57 input voltage is used.

Did you power hEX PoE with required PSU?

sch

Your StarTech ST10GSPEXNDP is not supported. At the link below you may find supported ethernet chipsets:
https://wiki.mikrotik.com/wiki/Supporte ... t_chipsets

sch

Hi, all the Mikrotik lovers! I need your help? I'm looking for a best practice for the Mikrotik Firewall Filer Rules. Maybe someone has a best practice for the Firewall filter rules in one place. This will help me a lot. Thank you C At official MikroTik wiki page you may find a lot of useful manual...

sch

The equipment is new, they have no more than a week of use. To get them to operate, I had to uninstall certain packages and stay alone with the basics, that way I achieved a space of 4 MB approx. Now if you save the settings and they remain after the restart. However, there is still not enough spac...

sch

Does it mean that LTE modem that is in the USB slot won't work?

Could you please describe to us how you are planning to connect USB interface to devices which do not have USB?

sch

According to the manufacturer of NAND chips, up to 5 blocks can be bad when NAND is manufactured, and up to 80 bad blocks could develop during operation, but it will not disturb the operation of your router, because complex workaround mechanisms are in place, that will copy the data to another block...

sch

Upgrade your device to latest stable or long-term RouterOS version, Winbox should be upgraded too.

sch

What's the point if you do not read it anyway?

sch

what about shortcuts guys ? :-) https://forum.mikrotik.com/viewtopic.php?f=21&t=137745&p=679086#p679086 What shortcuts? Where? Your link also doesn't explain what you want https://forum.mikrotik.com/viewtopic.php?f=21&t=139189&p=686485#p686485 I just dream about winbox, with optiona...

sch

Is there any ETA for long-term release which will fix vulnerabilities? You didnt read the thread, did you? I did, so far there has been only "as soon as possible". It's been 3 days! I don't get it why it is taking so long.. Fixes for CVE-2018-14847 were released for all channels at same d...

sch

Please send supout file from your router to support@mikrotik.com.
File must be generated while router is not working as suspected or after some problem has appeared on device.

sch

No, since this model has SPI flash, MetaRouter is not supported.

sch

This device might be incompatible with R11e-LTE international modem.
https://i.mt.lv/cdn/rb_files/1557999615 ... series.pdf

sch

You may use firewall rules to prevent login brute-force: https://wiki.mikrotik.com/wiki/Brutefor ... prevention

sch

Different hardware and switching possibilities:

https://mikrotik.com/products/compare/C ... G-2SplusRM

https://mikrotik.com/product/CRS125-24G ... estresults
https://mikrotik.com/product/CRS326-24G ... estresults

sch

Please try to follow these steps to load the backup bootloader: 1) Power your device off; 2) Press and hold reset button; 3) Power device on; 4) Hold reset button pressed for 1-2 seconds and then release; 5) If device boots up, then run command "/system routerboard upgrade". If previously ...

sch

Please send supout file from your devices to support@mikrotik.com.

sch

What's new in 6.42 (2018-Apr-13 11:03):
*) chr - added "qemu-guest-agent" and "virtio-scsi" driver on KVM installations;

Please upgrade your CHR RouterOS.

sch

2011 ok 951G ok hap ac lite...................... couldn't update to stable or testing from 6.43.11, went to 6.42.12 long..... ok. Retries to stable or beta nothing...... still stuck on long term. u can get the support file from here. https://mega.nz/#!JnZ1iIZL!MT9wQ2vhAXA4o0tSC2d3Q6LMz8vj93Uwv_xZn...

sch

MetaRouter is not supported on your device.
https://wiki.mikrotik.com/wiki/Manual:M ... r#Overview

sch

Please send supout file from your router to support@mikrotik.com.

sch

block all and allow know safe sites

sch

If you are using the latest RouterOS and firmware please contact the support@mikrotik.com attached the supout.rif file from the router generated during or after issue. Otherwise, upgrade RouterOS and firmware.

sch

At first upgrade your CCR to latest RouterOS and firmware version. It may help.

sch

/system package update> set channel=

https://wiki.mikrotik.com/wiki/Manual:U ... ase_chains

sch

Update your Winbox to 3.18

sch

Are static DNS added?

https://wiki.mikrotik.com/wiki/Manual:I ... NS_Entries

sch

No, in logs/suppout viewer you can see only an account name, what was used.

sch

Why do not use implemented RouterOS methods?
https://wiki.mikrotik.com/wiki/Manual:P ... Monitoring

sch

Please contact the support@mikrotik.com attached the supout.rif file from the router generated during or after issue:
https://wiki.mikrotik.com/wiki/Manual:S ... utput_File

sch

Please contact the support@mikrotik.com attached the supout.rif file from the router generated during or after issue:
https://wiki.mikrotik.com/wiki/Manual:S ... utput_File

sch

How I do resolve problem with no free disc space to upgrade firmware? I have HAP Lite with old FW, when I try to upload new pkg, - see error, "You have only 6.4mB of free space", Write error.. and new FW pkg is 7+ mBytes.. What i can delete for upgrade fitmware? Total is 16 mbytes.. AutoU...

sch

Please contact us at support@mikrotik.com with descriptions

sch

Or you can take a case from 2011...

sch

How will i do it with netinstall

Read this article: https://wiki.mikrotik.com/wiki/Manual:Netinstall

sch

At first try load backup bootloader:
https://wiki.mikrotik.com/wiki/Manual:R ... up_loaders
Or use Netinstall:
https://wiki.mikrotik.com/wiki/Manual:Netinstall

sch

Read this thread: viewtopic.php?f=2&t=134793

sch

http://i.imgur.com/d6i7AHO.jpg http://i.imgur.com/zhGQS7q.jpg Signal is excelent through 2 concrete walls (-51 on android phone) and also higher than an standard RB951Ui-2HnD with 2-5dbi. With standard tplink 841 signal was very poor and loose conectivity very often. This is just a testing projects...

Search found 94 matches