Hi, Running 6.44Beta20

No tx-power setting for the 60Ghz interfaces.

I've got several links that are very close and I suspect we can improve the quality by turning down the TX power.

Any idea when it will be a configurable option again ??

I've checkd, WinBox, WebFIg and CLI

Thank you

Hi, I'm trying to build a general template to monitor the UPS values I can get from a mikrotik router. The routers have a USB port that can talk to certain UPS's and report back data via UPS-MIB. My challenge is that if I do a query on tik-a with the following OID, it works. OID: .1.3.6.1.2.1.33.1.4...

I thought I would post a follow-up / resolved message.

First THANK YOU TO MIKROTIK SUPPORT / ENG team.

The issue ended up being an interesting corner case bug in the OSPFv3 code of RouterOS
I've tested 6.36rc10 and it's fixed in that version.

All OSPFv3 sessions are now operating as expected.

I thought I would post a follow-up / resolved message.

First THANK YOU TO MIKROTIK SUPPORT / ENG team.

The issue ended up being an interesting corner case bug in the OSPFv3 code of RouterOS
I've tested 6.36rc10 and it's fixed in that version.

All OSPFv3 sessions are now operating as expected.

OK, I can see you point. SO then why does OSPFv2 come up and just work on this exact same link?
It would also have MTU issue if there was MTU issues.

I am going to try and capture data

yes, to a DIFFERENT Cisco. So.


Cisco <--AF 24--> CCR <-wire-> Cisco <--fiber--> Juniper MX480 <--fiber> [The world BGP]

Cisco via AF24 to CCR OSPF v2 works, OSPF v3 DOES NOT

CCR via wire to another Cisco, OSPF v2/3 WORKS
Cisco to Juniper OSPF v2/3 Works

Hi, Yes, I read that thread. I'm running version 3.2 of the AF code. Here is the full topology, three sites, A, B, C A <--> B CCR to Cisco, OSPF v2 works, OSPF v3 does not, AF24 link B <--> C Cisco to CCR, OSPF v2 works, OSPF v3 works, AF24 link C <--> A CCR to CCR, OSPF v2 works, OSPF v3 does not, ...

Hi, As another datapoint that its not MTU, the CCR in question has a hard cable connection to another Cisco 3560G, and that session is just fine. When doing debug on the Cisco we get a "Bad request received" this request is from the CCR. Another note: NBMA does not bring up the adjacencies...

Hi, when looking at the OSPF debug from the Cisco there is no tell-tail MTU mismatch showing up in the logs. Also, OSPF v2 between these two routers is working just fine. Which further leads me to believe that MTU is ok. The Layer 3 MTU's match. The Layer2 MTU's match, no OSPF errors otherwise Thanks

Hi, We have two CCR 1036's running v6.34.3 They WILL form OSPFv2 adjacency just fine. The WILL NOT form OSPFv3 adjacency and stay stuck in Exstart and dropping from Full to 2-Way. I'm trying to bring IPv6 up on these new links hence the OSPFv3. The two routers are interconnected via a pair of AirFib...

Hi, Did you ever resolve this ? IF so what was the resolution / issue.

thanks

Hi, Is the elastic server at the same physical location as the phone ?
Or is the elastic server at another location and the SIP phones are remote ?

I upgraded the RB2011 to 6.34.3 so its the same version as the CCR now. That OSPFv3 session came right up no issues. I can reset it and it comes right back. So to recap: RB2011 <----Rocket M5 PTP Link----> Cisco 3560G Works just fine CCR <---AirFiber 24 PTP Link---> Cisco 3560G Stuck in EXSTART

Good point, I should have included that in the original post.

CCR v6.34.3
RB2011 v6.32.3

Cisco IOS: c3560-ipservicesk9-mz.150-2.SE2

The CCR was running 6.29 or similar and I upgraded it last night incase it was an issue.
Didn't have any impact on the problem.

Hi, I'm stuck and need some wisdom from the forms :) Summary: OSPFv3 between a Cisco Cat 3560G and a CCR-1036 is stuck in EXSTART state OSPFv3 between the same Cisco and a RB-2011 works every time. The Link between the Cisco and the CCR is via a pair of AirFiber24 radios. The link between the Cisco ...

Looks like a bug. Problem have been reported to DEV for fixing.

Thank you. Is there anything I can collect from our end that would be of value to the DEV team ?

Hi,
Just installed 6.35rc12

We are unable to upgrade client router boards.
Dude gives us an error message "router packages unknown"

We are trying yo upgrade 6.5 and 6.7 based tik's

Thoughts ?? How to resolve ?

Thank you

Hi, it would seem that webfig is sending MS-CHAP attributes when attempting to login and use radius backend. Same radius backend works just fine with SSH. I'm trying to use Radius as a centralized credential database for all of our tik's, cisco's, etc Thoughts ?? Code is 6.29.1 CCR 1036, RB2011, RB9...

Hi, I have a RB 751 configured as such. Ether 1 WAN uplink with a public /30 for ptp back to our aggregation router Ether 5 inside network, needs NAT to outside WAN IP Ether 4 inside network with PUBLIC IP subnet. This subnet is statically routed to the RB's WAN via our aggregation router. Issue is ...