MikroTik

bartjoo

That depends on your requirements and what you call "cheap". Probably a dumb wirespeed switch could work fine but when you want link aggregation it has to be a simple managable switch. The synology nas has link aggregration ;) But i just ordered the ccr 1009 :) Because -i dont want speed losing. -R...

bartjoo

When you don't have routing requirements between the servers and NAS it would be easier to just buy a separate
switch and put it between those.

hello, a simple cheap switch you mean?

bartjoo

https://i.mt.lv/routerboard/files/Block-RB1100AHx2.pdf I would put the NAS on ports 11-12-13. And each server on different switches. The one with the lower speed requirements on the same switch with the uplink. Or better yet, get a CCR-1009-1C-7G-1S where it doesn't matter since there are no switch...

bartjoo

Hello, i have Mikrotik 1100 router. On this router, there are 2 switches. Now i want to know, whats the speed between this switches? because i have 2 server on switch 1, and my synology nas with bonding (3UTP) on switch 2. But if the switches communication is maximum 1GBit, i dont use the maximum bo...

bartjoo

Hello, i got a problem with this latest version (6.34.3) and x86. I work with proxmox and mikrotik x86 installed. Never got problems until i updated to this version. Every night the Mikrotik server reboot the system at 6 am for a fresh new start ;) With this version (6.34.3) the ether1 is not always...

bartjoo

Hello, i have installed Capsman on 1 server and have 50 clients. Everything works great! Also the upgrades all together in one single click. But could someone tell me how to upgrade the firmware (routerboard versions) with Capsman? otherwise i need to upgrade every client seperatly. tnx for your rea...

bartjoo

Hello,
could you tell what the new features are for the next version (v3)?
And could you tell when v3 is planned?

bartjoo

Hello, could someone explain how the Mikrotik hotspot flow works? Like: Phone connect to the AP Capsman check for the MAC address in the hotspot radius Reject or accept Then give a ip to the Phone OR Phone connect to the AP Then give a ip to the Phone (gives mostly the captive portal, because the ap...

bartjoo

Yes i tried it with a new installation. same problem. I dont use priority's.
which setting do i have to check?

bartjoo

I have a 2011 at 1 home, and the crs at my other home. when i download without the vpn (the same file from the same place) its fast. when i use the vpn, its slow. I allready played with the MTU, the same result :( The strange thing is, when i put EXACT the same configuration to the crs, there is a p...

bartjoo

Hello, i allready tried LT2P and PPTP.
Hmm, so the 2011 is much better? you recommend to switch it?
Because this is to slow. Strange, because i thought the CPU must be 100% when he is 'working'

bartjoo

Hello, i have a VPN connection between my 2 houses. When i made the connection with the 2011 version, he got 100% CPU and 6,7MB/s speed. When i copie exact the same configuration to the CRS125-24-1s-2hnd, the CPU is max 50% and the Speed 2-3MB's. Is there a limit for VPN into the CRS? i would like a...

bartjoo

Does the 3011 series also include dual band 5Ghz by default or do we need to buy/switch miniPCIe cards ourselves? As the specs of the 2011 are quite similair to the CRS125 series, are there plans to upgrade the CRS125 series as well with the new ARM processor? A 3011 or CRS125v2 with dual band 2.4/...

bartjoo

Hello, great! new Products! (dualbands)
What are the differents between the 2011 and 3011 version?

RB3011UiAS-RM: $179

RB3011UiAS-2HnD-IN: $199

bartjoo

are you using wireless-fp package or wireless-cm2 package? The CAPs are connected to CAPsMAN via MAC connection or IP connection? Using wireless-cm2 package and connected via MAC. Very basic created Config and applied to the CAP when it showed up in the interfaces. Again, everything works fine unti...

bartjoo

I'm working in a testing environment with a very basic layout. I'm using the latest version of Router OS and CAPsMANv2 on 6.27. I have a 5 port RB450G gateway connected to a 5 port 750UP POE switch powering 4 RB912UAG-2HPnD APs. I have the 450G acting as the controller for the 4 APs. Everything wor...

bartjoo

I appreciate the quick response. My problem is I unhooked the CAPsMAN controller from the LAN for about 30 seconds and plugged it back up. Once plugged back in the access points never sync back with the controller? You'd think this would happen quickly and automatically. But, I'm unable to get the ...

bartjoo

I'm just starting to demo the CAPsMANv2. When I remove the CAPsMAN from the network for a few seconds and reconnect my APs(CAPS) do not reconnect unless I reboot or disable/re-enable the CAP in the wireless interface of the AP. Is this normal? Is there a setting I'm missing that allows the units to...

bartjoo

Currently CAPsMAN is not designed for management of the WISP APs as it doesn't support Bridge mode that is required for Station-Bridge and WDS that is required for the Station-WDS. We might add those features later when we have finished the rest of the CAPsMAN planned features. Hello, Is there a li...

bartjoo

Is there someone who can tell more about this feature? 1 building, 5 AP's everywhere in the building. I must place the in a group? so they know from eachother there are more AP's from the same network? OR is loadbalancing: 1 building, 5ap's near eachother. The 5 AP's have all the same WiFi distance/...

bartjoo

Hmm, i think i found something.
Even if i dont have a wifi connection, its possible to remote my apple tv.
so, its not a problem / question for capsman. sorry!

So, i will test capsman further. tnx for helping!

bartjoo

if your cap interface in the full forwarding mode is in the bridge port with your local network then you will be in the same local network where you wireless clients are connected. Hmm, i thought i know the problem. But its not. it dont work :( connected with the hotspot, i found the 192.168 adress...

bartjoo

I tried both. with and without the local bridge. in both options airplay is there. My config is: AP1 - FULL Forwarding to datacenter (VPN), this is my hotspot (10.5.50.0/24) AP2-virtual LOCAL FORWARDING with local bridge. (192.168.1.0/24) in the CAP MENU from the AP. When i connect to AP1, i dont wa...

bartjoo

Hello, another question. I made a FORWARDING bridge and it works fine.
But when i do a scan on this forwarding network, i found my apple tv airplay on the local network. How is this possible? This is a different network (or isnt?)
tnx for your help.

bartjoo

for me everything works now. local and forwarding.
another question, is it possible to use a variable for the SSID?
like: SSID: Test_[Identity] ?
Greetz
Bart

bartjoo

Hello, i have a question about the dude. I have some VPN clients who logging in to the mikrotik main server. This is not the default route for the clients. With the dude i monitor normaly on IP address, but now the VPN clients have different IP's from the pool. So i want to use DNS name from the VPN...

bartjoo

Ah! The provisioning works! i had to delete the Interfaces.

now i will try the local forwarding.
i found this document.
http://file.accesspoint.hu/pdf/uldis.pdf
greetz

bartjoo

Hello, Question1: i want to auto provision with the auto provision tab. But it dont work :( I connect the AP with the CAPsMan. That works. When i put the CFG in the CAP on tabblad INTERFACE, it works. But when i go to tab Provisioning, and make a new rule, it dont work on the interfaces. :( Someone ...

bartjoo

Hello, i have the same problem: sometimes it works, sometimes the logging says: Error sending e-mail <scriptname>: error handling file. Is there someone who can explain whats happen? /export file=([/system identity get name] . "-" . \ [:pick [/system clock get date] 7 11] . [:pick [/system clock get...

bartjoo

Hello, i used this:
/interface wireless access-list
add signal-range=-70..120

and DEFAULT AUTHENTICATE @ the Interface wireless page OFF.
(not the AUTHENTICATE @ the Interface wireless access list page)

but iam waiting for the roaming option..

bartjoo

Hello Folks! At RoS6.7 L2TP was working properly, after RoS6.7 L2TP stops transferring data after anything between 70Kb to 13MB. The same goes for V6.13. It is for all RB platforms, RB411, RB433, RB333, RB600, RB2011UAS, RB750 and so on. Anyone else who had experiense of problem with L2TP ? I will ...

bartjoo

Hello everyone, i use al lot off hotspots in my network. but when i upgrade my routers to the latest version, the upgrade have some problems. The ip addresses are active the bridge and change after the upgrade to a WLAN connection OR The dhcp server was active on the bridge and after the upgrade its...

bartjoo

Hello, is there a release list (features, fixes, bues) for Capsman to?

bartjoo

ah oke

i understand.
thats no possible. because someone go to httpS://google.com en he want the certificate of google.com. he cant get it.

thats why you need to accept this.

bartjoo

Ah, but when v7 comes out, no one knows i think?

is there a work around with a script or something like that?

bartjoo

Hello, does someone know if its possible to do Accesspoint load balancing with Mikrotik Devices? So, when there are 2 Mikrotiks in 1 building, the device must connect to the best Wireless signal AP. Maybe its possible to setup a rule like: if noise floor = more then X then KICK the client. The clien...

bartjoo

Hello,
we use the externa loginpage.
Could you explain your settings?

bartjoo

I found the solution for my problem.

i installed the certifcate (.cer) on the mikrotik and FORGOT the .key certificate installation.
I installed also the CA certificates.
i checked the HTTPS at the hotspot settings.

Now the https login page is visible for everyone.

bartjoo

hello, i tried it.. but i got the IE and firefox message :
the page cant be displayed.
make sure TLS and SSL protocals are enabled (they are)

he is searching for a certificate from (example) google.nl ... but he cant find it because he cant go to it thru the firewall....

bartjoo

Hmm, i have the same problem. Lots of pages are https. so the problem is always there. who has a solution for this. Mikrotik maybe? I have a certificate on the login page. Everything works fine.. But with the mikrotik hotspot functionality he wants to the real page like Google. And that doesnt work....

bartjoo

Wow! great! tnx.. i will try it!

bartjoo

Hello, iam searching for a script who disabled the WLAN connection when there is no reply on a ping, when there is a reply, he must turn on the WLAN connection. who have one like this or could make it for me? I have some hotspots and i dont want a SSID sending out when there is no internet connectio...

bartjoo

I have a question about my hotspot network. I got 1 dhcp server with hotspot functionality. I got 4 hotspots in 4 different citys. They are connected with a EoIP connecting to the dhcp server. I made a bridge between the wireless and the EoIP. So i got a DHCP lease from the server when i connect wit...

bartjoo

Hello there. i have a question about the hotspot functionality. I have 4 stores. i have 1 DHCP server (mikrotik) and 4 AP's. I want on every store his own hotspot functionality but with the same DHCP server. Who can tell me the settings for this? i cant find them. Ik make a connection with EoIP betw...

bartjoo

Hello there. i have a question about (i think) meshing. i have 2 AP's with UTP to 1 backend router. The Backend router is the DHCP server. I want to setup the AP's in meshing. So when 1 AP is full,he must know AP2 is free for connections and send the connections to AP2. Like loadbalancing over the 2...

bartjoo

tnx for your reaction.
i have MAC, HTTP CHAP, HTTP PAP on.
is this incorrect?

bartjoo

Hello, when i connect with my iphone 4 to my hotspot, the first time he will connect correcly. but sometimes the connection changes into AUTO-LOGIN functionality (see attachment). how is this possible? is this a bug in ios6? i dont want to tell my customers sometimes the must change the wifi setting...

bartjoo

When will there be a new version of The Dude?

Yeah, when is there a new (beta / final) release?
greetz
Bart

bartjoo

Hello, i have a external radius server. I get the MAC adresses from the client, but i want the device name (iphone, android, win7) and the name from the user in the device (iphone from Bartjoo) in my database logging too. Is this possible? Maybe with the radius or with a script? In the DHCP server f...

bartjoo

Hello there, when i use the mac adress authenication with a external radius the Mikrotik try to logon every minute (accept-accept or reject-reject). Where is the variable to change the 60 seconds into 20 seconds? If its nog possible to change it, please make it a variable in the mikrotik settings. g...

bartjoo

Hello, the reset button and jumper doesnt work for me.
How can i use netinstall? I dont have a com port
On the mikrotik 951g. And he reboots every time, so i dont have time to logon

update:
it works:)
http://www.mikrotik.com.my/reinstalling ... rial-port/

bartjoo

After the installing my RB is rebooting everytime. He never came up.
with hard reset it doesnt work.. every time a reboot in 60seconds..
help me!

bartjoo

Hello, i got it. i have to wait longer in TAB THE DUDE.

second question. is it possible to get the notifcation error from the server. or need i setup every agent separately?

bartjoo

nobody?

is there a manual / youtube movie where i can learn how to setup (settings explenation) this windows dude server with dude agents (mikrotik devices)

i cant find it.

bartjoo

i mean this: Dude server - If it's another Dude server that could be used as an agent. Devices marked as Dude Servers also have a Dude tab in their settings, where you can directly view their maps, without disconnecting from the currently opened server. i got the tabblad, but i dont have information...

bartjoo

Someone?
is there a setting to accept the dude mikrotik devices in the (firewall or something) windows client?

bartjoo

Hello, i have installed the dude server/agent on my mikrotik devices. I have installed the dude installed on my windows server. The devices and my windows server are on a different locations. they are connected with a VPN. Now i want in the windows client show the network behind the Mikrotik device....

bartjoo

Hello there. i have free radius server installed Radius manager 4 Mikrotik router. Now i want a login page where users online have to click LOGIN (without giving informatie like a name or something) and in the backoffice (mysql) a new user (mac adress device as username) will registrered. Who can he...

Search found 58 matches