Community discussions

MikroTik App

Search found 65 matches

by zhex900
Thu Jul 05, 2018 1:50 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

Hi,

My uplink is 25 MB/sec. 93% cpu only when I do a speed test. It only stays at this level for a few seconds.

Thank you for all your help.

I have just installed it in both houses. Hopefully, nothing will break.
by zhex900
Thu Jul 05, 2018 2:40 am
Forum: Beginner Basics
Topic: Allow remote access by device mac address
Replies: 1
Views: 1032

Allow remote access by device mac address

Hi, I have added the following rules to allow remote access. How can I restrict remote access to certain devices based on their mac-address. `src-mac-address` does not work. /ip firewall filter add action=accept chain=input disabled=no dst-port=8291 protocol=tcp /ip firewall filter add action=accept...
by zhex900
Wed Jul 04, 2018 11:27 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

HI,
I have another question. The CPU will clock max at 93% when I run a speed test. Is it possible to use the switch chip to free up some load on the CPU? My guess this is not possible because mangle rules are processed by CPU.
by zhex900
Wed Jul 04, 2018 11:18 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

HI Sindy, It is finally fixed. The problem I copied the config by restoring the backup from one router to another router. This caused the two routers to have the same mac address. I have reset the mac address on all interfaces. Changed the mac address on bridge-local. Now I have no packet loss. Than...
by zhex900
Wed Jul 04, 2018 3:55 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

Here is another file.
https://drive.google.com/file/d/1dXzadC ... sp=sharing

I don't know how to see the packet loss in Packet Sniffer.
by zhex900
Wed Jul 04, 2018 3:38 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

I will post it again after packet loss occurs.

This is my university's ip address. unsw.edu.au 202.58.60.194
by zhex900
Wed Jul 04, 2018 3:15 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

Here it is

https://drive.google.com/file/d/1dXzadC ... sp=sharing

192,168.80.253 is my laptop's ip address
by zhex900
Wed Jul 04, 2018 2:43 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

check-gateway=ping Should I uncheck this in ip route? [admin@MT-30] > /tool sniffer print only-headers: no memory-limit: 100KiB memory-scroll: yes file-name: pingloss.pcap file-limit: 8000KiB streaming-enabled: no streaming-server: 202.58.60.194 filter-stream: no filter-interface: ether1,ether2 filt...
by zhex900
Wed Jul 04, 2018 2:26 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

Sorry I cannot make any sense of the sniffer file.

https://drive.google.com/file/d/1dXzadC ... sp=sharing

How can I adapt to persistent user sessions PCC for my situation? Will it help?

https://wiki.mikrotik.com/wiki/NTH_load ... masquerade
by zhex900
Wed Jul 04, 2018 12:30 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

It's better now. But I still get 25% packet loss. The ping packet loss is only after pinging for a few minutes. The initial ping is fine. Packet loss increases as ping continues. ether2 cable is brand new and it is very short. The routers are right next to each other. If I switch off either ether1 o...
by zhex900
Tue Jul 03, 2018 1:23 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

Re: DUAL WAN PCC

Hi, It is almost working. There is still an ignoring problem. I get 20-50% packet loss! The result is the same if turn off either ether1 or ether2. At least I know both ports (ether1 and ether2) can serve internet traffic. Packet loss behaviour is not consistent. Packet loss reduces as I ping more. ...
by zhex900
Sun Jul 01, 2018 2:34 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Not possible. One wire only.
by zhex900
Sat Jun 30, 2018 11:58 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Hi Sindy,

I do understand the concept of it. But I just don't know how to implement it. Please have another go at it. I am close to solving it.
by zhex900
Sat Jun 30, 2018 12:06 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Hi Sindy,

I tried my best to follow your suggestions. Unfortunately, I cannot get to work. To make things clear, I have made a separate post. Your help is much appreciated.

viewtopic.php?f=2&t=136302&p=671393#p671393
by zhex900
Sat Jun 30, 2018 12:01 pm
Forum: General
Topic: DUAL WAN PCC
Replies: 21
Views: 1855

DUAL WAN PCC

Hi, I need some help with dual wan PCC configuration. I have two routers connected by one cable on ether2. The two routers have their independent respective internet connection. What I want to achieve is for both routers to share their internet traffic. Router A have subnet 192.168.80.0/24 and Route...
by zhex900
Thu Jun 07, 2018 2:38 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

So the resulting configuration would be symmetric like this: Router A Router B WAN1 WAN2 |\ /| | \______________________________________________________ / | | ether2 ether2 \/ | | ______________________________________________________/\ | | / \ | |/ \| PCC PCC | | bridge-lan A bridge-lan B And the ...
by zhex900
Wed Jun 06, 2018 2:35 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

While my purpose is for both routers have two WAN. Like what you suggested. My initial thinking was to have two interconnection links eth2 and vlan. Eth2 will direct internet A to B. Vlan will direct internet B to A.

Is vlan still necessary?
by zhex900
Wed Jun 06, 2018 2:08 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Do I still need the vlan?
by zhex900
Wed Jun 06, 2018 1:11 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

I am not sure I understand everything.

I will remove eth3 from bridge wan and delete bridge wan.

eth2 remain as 192.168.88.1. Vlan will have interface eth2.

I will add pcc rules on both routers. I only had them on router A.

What route rules should I have ? Avoid the problem of round- robin.
by zhex900
Wed Jun 06, 2018 11:15 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

I changed the vlan interface to bridge-wan on router B. Is this what you are referring to? I don't need eth2 and eth3 to be bridged together. eth1 and eth2 are together. rest are all bridge-local. I can't touch the ip address on bridge-wan and eth0. If I disable one I will lose the router connection...
by zhex900
Wed Jun 06, 2018 9:48 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Router B [admin@MikroTik] > /export hide-sensitive # jun/06/2018 16:48:06 by RouterOS 6.42.1 # software id = YSFQ-H9GG # # model = 2011UAS-2HnD # serial number = 419E0125FDC1 /interface bridge add fast-forward=no name=bridge-lan add admin-mac=00:0C:42:F8:A5:78 auto-mac=no comment=defconf name=bridge...
by zhex900
Wed Jun 06, 2018 9:47 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Router A [admin@MT-MAIN] > export hide-sensitive # jun/06/2018 16:47:11 by RouterOS 6.42.3 # software id = 6I1X-92CP # # model = 2011UAS-2HnD # serial number = 402602239286 /caps-man channel add band=2ghz-b/g/n control-channel-width=20mhz name=2G add band=5ghz-a/n/ac control-channel-width=20mhz name...
by zhex900
Wed Jun 06, 2018 9:41 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Router A COOKST bridge is used for CapsMAN. All ports are on the bridge-local. I am not sure whether vlan should also be on it. For now, I disabled it. I don't see any difference. [admin@MT-MAIN] /interface bridge port> print Flags: X - disabled, I - inactive, D - dynamic, H - hw-offload # INTERFACE...
by zhex900
Wed Jun 06, 2018 9:35 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

I really appreciate your help. Kindly look at my configures. Router B is a simple configure. I started with reset configurations. I selected a standard router configuration with NAT and bridged all ports. I added a new bridge. Rename the bridges into bridge-wan and bridge-lan. bridge-wan have eth1, ...
by zhex900
Wed Jun 06, 2018 12:59 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Hi, I have added the passthrough. But I only see traffic on WAN1. Nothing on WAN2. /ip firewall mangle add action=accept chain=prerouting dst-address=192.168.80.0/24 in-interface=bridge-local add action=accept chain=prerouting dst-address=192.168.88.0/24 in-interface=bridge-local add action=mark-con...
by zhex900
Tue Jun 05, 2018 5:02 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

I deleted my old routes and these again. Now I get more traffic on wan2, but little on wan1. Create the unmarked default routes /ip route add dst-address=0.0.0.0/0 gateway=192.168.0.1 distance=1 add dst-address=0.0.0.0/0 gateway=192.168.88.1 distance=2 Create the marked default routes /ip route add ...
by zhex900
Tue Jun 05, 2018 3:57 pm
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

I finally, got it working. I have added a static route on Router B, 0.0.0.0 with gateway 192.168.81.1. Router B has an internet connection and are switching for Router A. But I am not sure PCC is working probably on Router A. My understanding is that internet traffic is shared between wan1 and wan2....
by zhex900
Mon Jun 04, 2018 7:29 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Basically, I want both houses to share their internet. Sometimes, the internet connection is slow on one of the houses. When the internet is slow I want the traffic to be routed to the better connection. My thought is to use Router A as dual WAN for both houses. Router B does not directly get the in...
by zhex900
Mon Jun 04, 2018 6:59 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

Thank you for your reply. Ok, I can stick with software bridge. How do I setup Router B Bridge-LANB as a switch to Router A? I mean, using VLAN-HOUSELINK as the link between the two routers. Do I need to set up a static route from Router B?
by zhex900
Mon Jun 04, 2018 6:03 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

Re: VLAN SWITCH

5 ports for the switch is fine with me too. Port eth6 to eth10. How do I do this? I will read you post soon.
by zhex900
Mon Jun 04, 2018 2:57 am
Forum: General
Topic: VLAN SWITCH
Replies: 38
Views: 2863

VLAN SWITCH

30CookstNetwork.jpg Hi, I want to use two Mikrotik rb2011 to connect two houses together with one cable. Each house has its own internet service. My goal is to use dual WAN on both routers. The attached diagram shows my setup. Router A has two WAN ports, ETH_1 and ETH_2. ETH_2 uses Router B as a ga...
by zhex900
Mon Jun 04, 2018 1:12 am
Forum: General
Topic: VLAN bridge switch [SOLVED]
Replies: 7
Views: 1352

Re: VLAN bridge switch [SOLVED]

Hi,

I finally got the vlan working. The problem was with the switch configuration. I reset my router to default. Added VLAN their ip address. It is working fine. Thank you.
by zhex900
Sat Jun 02, 2018 9:39 am
Forum: General
Topic: VLAN bridge switch [SOLVED]
Replies: 7
Views: 1352

Re: VLAN bridge switch [SOLVED]

Anything to do with switch vlan? Router A [admin@MikroTik] > /interface vlan export # jun/02/2018 16:36:30 by RouterOS 6.42.1 # software id = YSFQ-H9GG # # model = 2011UAS-2HnD # serial number = 419E0125FDC1 /interface vlan add interface=ether2 name=vlan-100 use-service-tag=yes vlan-id=100 add inter...
by zhex900
Sat Jun 02, 2018 7:51 am
Forum: General
Topic: VLAN bridge switch [SOLVED]
Replies: 7
Views: 1352

Re: VLAN bridge switch [SOLVED]

Thank you. But I cannot get VLAN working. I have named VLAN on both routers as VLAN-100 set on interface eth2, tagged, VLAN ID 100. Connected the two routers on port eth2. Set the ip address on RouterA VLAN-100 192.168.80.2/24, network 192.168.80.0 RouterB VLAN-100 192.168.80.3/24, network 192.168.8...
by zhex900
Fri Jun 01, 2018 12:48 pm
Forum: General
Topic: VLAN bridge switch [SOLVED]
Replies: 7
Views: 1352

VLAN bridge switch [SOLVED]

Hi, I need some help to get this setup to work. Both routers are RB2011UAS-2HnD Router A (192.168.80.1) ISP A | ISP B. | wan1 | wan2 | ------------------------------------- eth1 | (eth2, valn1) | eth3-eth10 ------------------------------------- | | | Router B | (192.168.88.1) -----------------------...
by zhex900
Thu May 17, 2018 5:21 am
Forum: Wireless Networking
Topic: Wireless P2P with no line of sight
Replies: 1
Views: 515

Wireless P2P with no line of sight

Hi, I have two houses 1.8 KM apart. The land is not flat. The elevation of one house is 90.3 meter or 296.1 feet. Another is 60.1 meter or 197.1 feet. Is it possible to connect the two houses? The left starting point is at 60 metres and right ending point is at 90 metres. The house at the right end ...
by zhex900
Thu May 17, 2018 4:50 am
Forum: General
Topic: Dual WAN - load balancing
Replies: 1
Views: 425

Dual WAN - load balancing

Hi, I have two properties connected via a physical CAT6 cable. Both properties share a common wall. Each house have their own separate internet service. It is possible for both houses to have a dual wan with load balancing? Is it possible? I understand it is possible for one house to have two WAN wi...
by zhex900
Thu May 17, 2018 4:42 am
Forum: Wireless Networking
Topic: Capsman different Cap and WAN interface
Replies: 0
Views: 369

Capsman different Cap and WAN interface

Hi, I have two properties connected via a physical CAT6 cable. Both properties share a common wall. Each house have their own separate internet service. I want to use a one CAPsMAN to manage all the APs, in both houses. Is it possible for the house 2 to be connected with house 1 for CAP management b...
by zhex900
Tue Oct 27, 2015 5:31 am
Forum: Scripting
Topic: PPPOE client disconnect and connect command
Replies: 3
Views: 2433

Re: PPPOE client disconnect and connect command

/ppp active print returns nothing. What should I do? /interface pppoe-client print Flags: X - disabled, R - running 0 R name="pppoe-out-iinet" max-mtu=1492 max-mru=1492 mrru=disabled interface=ether1-gateway user="churchinperth" password="xixI3WFo9" profile=default keepalive-timeout=disabled servic...
by zhex900
Wed Oct 21, 2015 2:40 am
Forum: Scripting
Topic: PPPOE client disconnect and connect command
Replies: 3
Views: 2433

PPPOE client disconnect and connect command

Hi,

I want to disconnect and reconnect pppoe client in MK via command line. This is not just disable and enable pppoe. The Webfig GUI allows you to reconnect the pppoe client. How do I do this via the command line?

Thank you

Jake
by zhex900
Wed Aug 19, 2015 5:00 pm
Forum: General
Topic: Multiple public IP addresses with one /29 framed IP address
Replies: 7
Views: 1646

Multiple public IP addresses with one /29 framed IP address

Hi, My ADSL service provider assigned me a static public address and a block of 4 ip addresses. My MikroTik uses PPPoE client with an ADSL modem as bridge. So MikroTik get a public ip directly from my ISP. Default public ip: 203.10.132.253 Additional ips: 203.10.17.24 203.10.17.25 203.10.17.26 203.1...
by zhex900
Fri Jun 26, 2015 6:52 am
Forum: General
Topic: Mikrotik-Recv-Limit does not terminate session
Replies: 0
Views: 643

Mikrotik-Recv-Limit does not terminate session

Hi, I want to find out why Mikrotik-Recv-Limit attribute does not terminate session when the user reached data limit. I am using freeradius to logon wifi users. I am not using hotspot or ppp. Session-Timeout does terminate session when the time limit is reached. Mikrotik-Recv-Limit is sent to the NA...
by zhex900
Sat Jun 13, 2015 3:28 am
Forum: General
Topic: Mikrotik-Recv-Limit. Not ending session when reached limit
Replies: 7
Views: 2222

Re: Mikrotik-Recv-Limit. Not ending session when reached limit

Does anyone have any ideas?
by zhex900
Sun Nov 30, 2014 3:17 pm
Forum: General
Topic: Mikrotik-Recv-Limit. Not ending session when reached limit
Replies: 7
Views: 2222

Re: Mikrotik-Recv-Limit. Not ending session when reached lim

Your script is for hotspot users. I don't use hotspot. My clients use EAP to connect directly into the network. So your script cannot help me.
by zhex900
Thu Oct 16, 2014 11:45 am
Forum: General
Topic: Support for RADIUS attributes
Replies: 0
Views: 999

Support for RADIUS attributes

Currently I have a MikroTik (MT) router using EAP authentication via a FreeRadius server running Debian. Users can connect to the wireless service. I want to set traffic limit for each user. So I use MT-Total-Limit in the reply attribute. But MT router does not terminate the session when the limit i...
by zhex900
Wed May 28, 2014 3:35 pm
Forum: General
Topic: Map local ip to a public web address
Replies: 5
Views: 898

Re: Map local ip to a public web address

I am not not familiar with L2TP. Is this setup what you referring?

http://wiki.mikrotik.com/wiki/Manual:Interface/L2TP

This will work for me. But it will take some time for me to learn how to implement this.

Thanks
by zhex900
Wed May 28, 2014 2:07 am
Forum: General
Topic: Mikrotik support for Radius attributes
Replies: 2
Views: 1070

Re: Mikrotik support for Radius attributes

Hi, I thought user manager does not support EAP authentication. How do I configure userman to control wireless users? Are you referring to this? http://wiki.mikrotik.com/wiki/User_Manager/Wireless_Example This configuration does not use EAP. The username is the Mac address not a userman setup in the...
by zhex900
Tue May 27, 2014 8:44 am
Forum: General
Topic: Map local ip to a public web address
Replies: 5
Views: 898

Re: Map local ip to a public web address

Yes. I want redirect all traffic from an ip address to a web address. In my situation, I want my Mikrotik router to talk to a radius server with no static ip. Radius client only can have a static ip address of the radius server. It's a problem because my radius server's ip address will change. So I ...
by zhex900
Tue May 27, 2014 8:32 am
Forum: General
Topic: Map local ip to a public web address
Replies: 5
Views: 898

Map local ip to a public web address

Hi,

I want to map a local ip address (192.168.88.2) to a public address (http://www.google.com). So whenever I enter 192.168.2 it will go to http://www.google.com. How do I do this? Is it possible to do this?
by zhex900
Mon May 26, 2014 2:59 pm
Forum: General
Topic: Mikrotik support for Radius attributes
Replies: 2
Views: 1070

Mikrotik support for Radius attributes

Hi, I understand that Mikrotik support radius attributes in PPP and hotspot. But I want use Mikrotik as wireless access point only. So I don't want to use PPPoE or hotspot. Is it possible for me to use Mikrotik for this purpose? For example, when an user logins. Radius server sends MT-Total-Limit. M...
by zhex900
Thu May 22, 2014 3:46 am
Forum: General
Topic: Mikrotik-Recv-Limit. Not ending session when reached limit
Replies: 7
Views: 2222

Re: Mikrotik-Recv-Limit. Not ending session when reached lim

Is Mikrotik-Recv-Limit is only supported by hotspot and PPPoE? If this is the case why Session-Timeout worked?

What I want to achieve is to set a data quota for each wireless user.

Can anyone help me?
by zhex900
Wed May 21, 2014 3:27 am
Forum: General
Topic: Mikrotik-Recv-Limit. Not ending session when reached limit
Replies: 7
Views: 2222

Re: Mikrotik-Recv-Limit. Not ending session when reached lim

Hi,

I am not using PPPoe or hotspot. It is only for wireless authentication.

Do I need to set Acct-Interim-Interval in the reply item? Is 600 (10 mins) ok?

I thought NAS should terminate the session not the the freeradius' job right?

Jake He
by zhex900
Tue May 20, 2014 11:15 am
Forum: General
Topic: Mikrotik-Recv-Limit. Not ending session when reached limit
Replies: 7
Views: 2222

Mikrotik-Recv-Limit. Not ending session when reached limit

Hi, I am trying to limit user's download with Mikrotik-Recv-Limit. However NAS does not terminate the session when the limit is reached. Radius is working fine. It stops the user from login when the limit is reached. Accounting is working fine. Mikrotik-Recv-Limit is received by the NAS in Access-Ac...
by zhex900
Fri May 16, 2014 5:32 pm
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

Hi,

It finally worked. I had configure my freeRadius. This is work I did.

Only for EAP-TTLS works. EAP-PEAP still does not send Session-Timeout in Access-Accept.

vi eap in /etc/freeradius/mods-enabled

use_tunneled_reply = yes for everything.

Thank you for helping me.

Jake He
by zhex900
Fri May 16, 2014 3:52 am
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

I think, I know what the problem is now.

I have not setup PPP on my NAS. http://wiki.mikrotik.com/wiki/Manual:PPP_AAA
Is this correct? If it is, can someone point me a good tutorial concerning it?
by zhex900
Thu May 15, 2014 4:30 pm
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

I upgraded to v6.12. It still does not work. Do I need to install some packages or enable some service? I have taken a screenshot of my current packages.
by zhex900
Thu May 15, 2014 4:00 pm
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

I am using RouterOS v5.24. Is it ok?
by zhex900
Thu May 15, 2014 3:52 pm
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

A little progress. But NAS does not terminate the session when the time limit is reached.

I change my device authorisation method to EAP-TTLS, Session-Timeout is received on NAS (MikroTik). I set Session-Timeout = 300 (5 mins). But my device can still be connected after 5 mins.

What do I do now?
by zhex900
Thu May 15, 2014 10:29 am
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

I turned on CoA on FreeRadius and enable incoming radius in NAS. But it is still the same.
by zhex900
Thu May 15, 2014 7:25 am
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Re: Freeradius Session-Timeout

Thank you for your help.

I don't know much about CoA. FreeRADIUS support it. Is it ok if I don't use it?
by zhex900
Wed May 14, 2014 5:12 am
Forum: General
Topic: Freeradius Session-Timeout
Replies: 11
Views: 8003

Freeradius Session-Timeout

Hi, I have trying to setup Freeradius to work with my MikroTik as a NAS. My aim is to have session time limit per user. Now user can log in. Session time limiting is working on the radius server. The radius rejects the user when the time limit is reached. However my problem is the NAS does not recei...
by zhex900
Mon Apr 28, 2014 12:03 pm
Forum: RouterBOARD hardware
Topic: RB2011UAS-2HnD-IN Netinstall without serial cable
Replies: 4
Views: 8710

Re: RB2011UAS-2HnD-IN Netinstall without serial cable

Thank you for your reply.

Do I follow this instructions?
http://www.mikrotik.com.my/reinstalling ... rial-port/

I tried but the netinstall cannot find my router. I connect a cable in eth1 into a computer.
by zhex900
Mon Apr 28, 2014 4:30 am
Forum: RouterBOARD hardware
Topic: RB2011UAS-2HnD-IN Netinstall without serial cable
Replies: 4
Views: 8710

RB2011UAS-2HnD-IN Netinstall without serial cable

Hi,

My RB2011UAS-2HnD-IN is stuck in "loading kernel". So I want to use netinstall to reinstall firmware. But I don't have a serial cable.

Is there a way to do netinstall without a serial cable. Should I use normal network cable in the serial port?

Jake
by zhex900
Thu Apr 24, 2014 3:06 pm
Forum: General
Topic: Freeradius Port-Limit simultaneous-use
Replies: 3
Views: 1886

Freeradius Port-Limit simultaneous-use

Hi, I am trying to limit each user to have one session only. Currently, I can login via NAS (MikroTik) through a freeradius server. However simultaneous-use is not working. I have set Simultaneous-Use to 1 in radcheck. Port-Limit to 1 in radreply. NAS received Port-Limit=1. I can see it in the log. ...