MikroTik

ckleea

Thanks, What I need to do is to add some ax devices in remote site and get the CAPsMAN forwarding work. Is that possibl No, capsman forwarding with new capsman is not possible. Period. You'll have to consider other mechanisms (e.g. VLAN) to achieve same goals as you get with capsman forwarding. Or ...

ckleea

Can someone help?
Depends on how you want it to work exactly. Fyi, legacy supports CAPsMAN forwarding, wifi-qcom(-ac) doesn't.

Thanks, What I need to do is to add some ax devices in remote site and get the CAPsMAN forwarding work. Is that possibl

ckleea

I finally get a AX3 from a remote site to connect via CAPs. However, the remote site AX3 got IP address from the DHCP server at the remote site but not from the new CAPsMan. I am not sure it is correct, some say local forward in the legacy CAPsMan does not work

Can someone help?

ckleea

I want to know how to have both legacy and new CAPsMan on my x86 routeros as main router 1 have been using x86 for many years and in my network, a few hAP and ac2 are working well as AP connected to the legacy CAPsMAN in x86. I wish to add on some AX3 to use WPA3. Do I have need to have both wireles...

ckleea

Config on capsman controller?

capsman.png

For me it is working fine.

Sorry, I read incorrectly

ckleea

I tried this before via internet but found the same result.

Hope this can be fixed.

ckleea

What I do is on different public IPs for CAPsMan and CAP In CAPsMan 1, it can be done as specifying the CAPsMan public IP in the CAP menu of AP and the firewall of CAPsMan allows UDP 5246, 5247. It works well all along including in the same city and overseas via internet. In my case, CAPsMan 2, I pr...

ckleea

Now at remote side, AX3 reports timeout or No suitable CAPsMan found

ckleea

An update,

I brought the AX3 back and installed in the LAN, it worked with the x86 device that has both CAPsMAN 1 and 2. Configuration was not that difficult.

Now wait to see if the same AX3 works again in remote site

ckleea

If issue persists while 7.14.2 is installed on CAPs and CAPsMAN, please create supout.rif files on involved devices and share the files with us support@mikrotik.com This issue should be resolved in latest versions. I use both 7.15.beta9 in my x86 as CAPsMan 1 + 2 and AX3 as CAP. From the AX3 log, i...

ckleea

Your CAPS that can't connect try to reach your CAPsMAN server via WAN? Then check your firewall rules? I try two routerOS device on the same network - one with legacy wifi; connect and work with CAPsMan 1; the other is a AX3 could not connect Both point to the same IP address and I open up UDP port...

ckleea

Remote CAP means outside LAN and connects via internet.

CAP in other devices connected via LAN works in CAPsMan 2

In legacy CAPsMan, I have made it work but never shows up as remote radio

ckleea

After some months, I still cannot make it work.

Any successful story to share? Remote CAP means CAP is connected via internet/WAN not LAN

ckleea

Can the script resolve the issue of mounting to a wrong position after a sudden reboot? I have several issues of this when the USB drive was mounted to a different name that containers won't start. As a result, I have to reformat the USB and reinstall the containers. The later takes a much loner tim...

ckleea

Sorry, don't understand the questions/statements. I could provision the RB4011 wireless interfaces locally because I have the "wireless" package. But I prefer to keep them managed via the legacy capsman on the same device as it is as of today. And yes, using local wifi capsman I cannot ma...

ckleea

Finally I use a very old laptop > 10 years with Windows XP to complete the netinstall procedure

Perhaps hAP ac2 may be the time to fade out

However, I still cannot make my AX3 work well for my requirememt

ckleea

Apart from netinstall, is there way to downgrade from 7.13? What I observed last night after few hours, 1. update to 7.13 with old wireless package and zerotier. Initially worked but afterward when reboot, not working. 2. I try netinstall but cannot find the device (may be I did not do the right res...

ckleea

Not yet.

May be later before New Year

ckleea

Yes, I noted this

But not sure how to have two CAPsMANs work in the same devices and how different APs can find its own CAPsMAN and work properly

ckleea

I have been using CAPsMan 1 for my local and remote AP. I know I need to allow UDP 5246, 5247 for traffic

When I upgrade to 7.13, I wish to try CAPsMan 2. I know it can be used on the same main routeros device. But seems it does not allow remote APs to come it when both CAPsMan 1 and 2 are on

ckleea

I lost all the containers which are working. As after a reboot, the path to USB stick was changed to USB3 instead USB2. Now all the containers are not able to coming up. Does anyone know how to adjust the settings for the correct path?

ckleea

Hi

Is there way to run a shell script in a running container so that I could populate some data?

I try cronjob but not able to do. Seem not supported.

Many thanks

ckleea

I have an error when checking for update packages in 6.46.4 It always shows file not found

ckleea

Upgraded RB4011 from 6.44.3 to 6.45.1 - no issues Well, actually there is one - the bridge MAC address has changed so the network discovery on Windows must be done again. In my case the bridge MAC addr is the same as for eth7 interface. Interesting what it depends on... Best Bam Here same issue on ...

ckleea

I found the issue that may be due to compatibility between the latest ROS DHCP driver and ethernet hardware/driver. In my setup of x86 hardware, I used to use routerOS KVM to create a virtural network interface for my linux client. The default network interface is based on redhat virtio. Under the l...

ckleea

For me solution was easy and I've made this complicate because I've followed all instructions in thread, reset RMPro remote control (now need to spend at least 2 hour to configure all devices again), changed all DHCP settings, etc etc etc ... Well, final solution for me was : get back from 6.44.3 t...

ckleea

With 6.45beta42 two Linux installs had trouble getting DHCP over Ethernet. Sorry can't provide supout - already downgraded to 6.43.* stable, will stay on that. The only "custom" DHCP setting I have is - lease time is 7 days. No trouble with WiFi clients. Router: AC^2. Similar issues encou...

ckleea

I encountered a strange issue recently After my debian 8 linux image was upgraded, the image remained as the old upon reboot. Not sure if one encounters similar problem in x86 KVM? Updated: my mistake in overlooking the checkbox of snapshot being enabled. Now it is resolved but facing other problems...

ckleea

Will it be available for x86 router soon?

I am also looking forward to have support in x86

ckleea

And each of 4 radios in fact gets the provision intended for it and is up and running as capsman interface? That's just the SSiD not showing on the devices, right? Are channels and all other wireless settings configured the same way in capsman as when running as stand-alone AP's? Please make "...

ckleea

Seems it works now.

Thanks for the help

ckleea

Yes, I have provisioning rule for 4 radios

ckleea

I have something strange that need help and advice. I have a X86 routerOS as main router and have two hAP ac to use as access point. CAPsMan is set up to control the two APs for dual band coverage. While the 2.4 GHz is working fine, I have problem in 5GHz as the SSID associated with it never showed ...

ckleea

But will there be plan for adding USB 3.0 support?

ckleea

I have issues after upgrade thet winbox disconnects after around two minutes. I need to re connect again

ckleea

The issue in modern hardware is USB support and upgrading an older version of routerOS to newer one.

I believe CHR will be easier to maintain.

ckleea

Will it be available for x86 router soon?

ckleea

Netinstall process should keep the license installed on your device. However, if you have doubts, then I recommend that you contact support@mikrotik.com before installation. The you might get a free replacement license if it will be lost after installation process (if you contact us first, not afte...

ckleea

Understand the current limitation. Fortunately the x86 motherboard has a serial port for me to set up initially

ckleea

To which version are you upgrading?

6.42.5 or 6.40 for the use of Ikev2

ckleea

I wish to upgrade my x86 to a newer firmware so that I can make use of the ikev2. However, every time I upgraded, upon reboot, I got error like this Loading system with initrd ERROR: Could not find disk! Please attach it somewhere else. How can I fix it? Should I use ISO to upgrade the system but I ...

ckleea

x86 has very limited USB3.0 support, it will probably work only in 2.0 mode.

Will more support for USB 3.0 add? I found a mulii LAN port fanless x86 MB to replace the existing one with a noisy fan. However, it has USB 3.0 ports.

ckleea

Hi, I am looking for help to install routerOS x86 on a new generation motherboard with USB 3.0 ports only. I try to adjust the BIOS but it has legacy mode. Wonder if USB 3.0 from intel is supported.

Thanks

ckleea

Is it ok to upgrade from 6.42rc3 to 6.42rc28?

I tried to upgrade from v21 to v24 and it caused by x86 routerOS fail to have connection. I have used sometimes to restore the older working version. The one I got at home was rc3.

ckleea

Is it possible to add /ip cloud ddns to x86 ROS? This has been asked here many times before. Mikrotik usually answers that /ip cloud depends on RouterBOARD serial number, so it can not be just added to x86 as it is. And there are no plans to work on any alternative solution. I also have a mikrotik ...

ckleea

Is it possible to add /ip cloud ddns to x86 ROS? It is already available in routerboard hardware and I think it should be extended to x86.

Thanks

ckleea

Hello everyone, I have successfully set up IKEv2 and i am able to connect from my iPhone and macbook, but connection drops every exactly 8 minutes. I have try various lifetime in proposals and played with settings without success. Here is my config # dec/22/2016 18:50:18 by RouterOS 6.38rc52 # soft...

ckleea

Someone please suggest in concern of RouterOS 6.xx ,1Gbps Bandwidth x86 hardware.... 1. Motherboard 2. Processor 3. RAM etc. Thanks & Regards Shuvodip Roy Depends on the ethernet ports you need and whether you need wifi as well. There are many good choices in China. I am using one with 6 giga p...

ckleea

You're right, it's system-dns=yes

I use XML mobileconfig file, read here:
https://wiki.strongswan.org/projects/st ... Ev2Profile

Can I have a copy of your ios mobileconfig?

ckleea

I got it working with Pre-Shared key with my iPhone using this config: /ip pool add name=rw-pool ranges=192.168.77.2-192.168.77.254 /ip ipsec policy set 0 level=unique dst-address=192.168.77.0/24 /ip ipsec mode-conf add name=cfg1 send-dns=yes address-pool=rw-pool address-prefix=32 /ip ipsec peer ad...

ckleea

I fixed the issue with ISO image to reinstall. Netinstall does not work at all. ISO image installation has an option to keep old configuration. Only issue is that it formats my 128GB SSD. Fortunately, it is x86. I took out the SSD and mounted it under a linux image. I managed to copy all the files i...

ckleea

Am also looking forwards to have sample configuration for IOS clients and site to site with Strongswan

ckleea

I have a routerOS for my x86 router. Recently I got problem in the update to 6.37. Upon restating after downloading, the router loses its connection i..e failed to boot up. Screen output showing directory / file missing. When I took out the msata and put it into a USB external drive, it boots but wi...

ckleea

I would like to ask if there is example on how to connect to a linux server who runs strongswan 5.x as IPSec VPN server.

ckleea

I am looking for a script to help to update my dyndns hosts

I have two wan IPs which is provided by my ISP provider by DHCP. Normally they change very infrequently. However, I would like to know if I could use script to change the IP provided to the two wan ports and then update my dyndns hosts.

ckleea

I found the same issue of KVM in x86 not functioning. It just showed starting but not running.
I have to restore back to 6.32.3

ckleea

bjornr and ckleea would be nice if you sent support output files to the support. Create the file after your attempt to start your image file. Also, while at it, check if you have kernel and initrd files supplied for the configuration. I use Debian Wheezy and Jessie to install the KVM. After success...

ckleea

I try to see if my small form factor x86 can be used as routerOS router. However, neither the USB ports 2.0 nor 3.0 is working upon booting up the system. I wonder if there is any need for the BIOS configuration. When I use USB keyboard, I can press the DEL key to the BIOS setup but it is not workin...

ckleea

My KVM image does not start. When click enable and start, it just briefly indicates start and then stopped.
I confirm this KVM behavior with i386 Debian image on x86

The same still appears in the 6.34 release candidate. After downgrade back to 6.32.3, it is back to normal

ckleea

My KVM image does not start. When click enable and start, it just briefly indicates start and then stopped.

An update: openwrt x86 images work as before but debian i386 images does not. Logging shows kvm error. VNC does not allow me to connect.

ckleea

My KVM image does not start. When click enable and start, it just briefly indicates start and then stopped.

ckleea

Will there be changed in memory limitation for routerOS x86? I know it is currently limited by 2GB. With better and 64 bits CPU available, and inexpensive and larger capacity memory available, I am looking forward to having 4GB or even more support in future.

ckleea

Supported

ckleea

Use Winbox to work with the kvm guest images and create 2 interfaces for access

This allows you to install system just like to work with other linux KVM.

Have a look of this thread
http://forum.mikrotik.com/viewtopic.php?f=15&t=101726

ckleea

I am now able to connect and install Debian Wheezy. What I need is to create 2 interfaces for the intended KVM image - one is static which is for VNC access and the second one is dynamic which is just like the virtual ethernet for the KVM guest. Once I did so, VNC can see the console message and I c...

ckleea

I am able to have openwrt as a KVM image under router OS but I want to use debian which I am much familiar. I can have a bigger size image i.e. around 2GB.

This is why I ask if there is guide to install debian i386 as a KVM image under routerOS x86.

ckleea

I mean, I cannot use the console within Winbox to see the netinst message during installation. At the same time, I cannot access via VNC.

Please advise how to make it work.

ckleea

Is it possible to install debian wheezy i386 into a KVM image under RouterOS x86?

I try to add a netinstall iso into it and it shows running. But I cannot access the kernel for installation.

ckleea

Can you share your config examples on both sides?

ckleea

Did you find a solution? I am also interested to have IPSec connection between mikrotik roiuter and my VPS with strongswan

Search found 70 matches