Community discussions

MikroTik App

Search found 9 matches

by ivtts
Fri Apr 17, 2020 11:08 am
Forum: General
Topic: Problem with Huawei E3372 4G modem
Replies: 69
Views: 138683

Re: Problem with Huawei E3372 4G modem

Hi, i'm testing Huawei E3372h (Megafon M150-2) with hEX PoE (960PGS). I'm don't remeber version ROS when testing, may be 6.46.5 (current stable) My modem does't recognize command 'AT^SETPORT', and have a stick firmware (not hilink). With default settings for ppp-out1 (when 'Dealing on demand' is che...
by ivtts
Thu Aug 29, 2013 10:42 pm
Forum: The Dude
Topic: Dude v4beta3 released
Replies: 253
Views: 103535

Re: Dude v4beta3 released

join, +1
by ivtts
Thu Aug 29, 2013 8:49 pm
Forum: General
Topic: opvpn client (mikrotik) of a Linux deban openvpn server
Replies: 15
Views: 19284

Re: opvpn client (mikrotik) of a Linux deban openvpn server

May be your firewall rules block ping from openvpn server. You may try disable firewall rules and try ping again. To disable firewall rules select IP->Firewall in Winbox. In window Firewall select the rule and press button with red cross to disable it (after you may enable it). Also check routes on ...
by ivtts
Thu Aug 29, 2013 6:53 pm
Forum: Beginner Basics
Topic: No rules work
Replies: 1
Views: 805

Re: No rules work

I checked the rules (26,28) in itself - as a result I wan `t to ping my router wan (your rules work properly, i recieve message that network is unreachable). But if I add your rule 27, i don't receive any answer (with message time interval exceeded). You can try to move these rules on the top of you...
by ivtts
Mon Aug 26, 2013 11:17 pm
Forum: Beginner Basics
Topic: Display packets logged by a firewall rule
Replies: 3
Views: 5536

Re: Display packets logged by a firewall rule

you may check that for topic info in "System->Logging" action memory is set(that is by default). If you have too many messages about "login failure", you may also set quantity of logged rows in memory ("System->Logging" and then "Actions", select memory and set value for "Lines")(don't set very big ...
by ivtts
Mon Aug 26, 2013 10:32 pm
Forum: Beginner Basics
Topic: Uploading the supout.rif file
Replies: 1
Views: 1018

Re: Uploading the supout.rif file

supout.rif is a binary file and (i suppose) not designed for restore (it designed for treatment in support). However you may view his content by uploading that on mikrotik.com into your account (you need register). For backup/restore you must use these Winbox commands: Files->Backup and Files->Resto...
by ivtts
Thu Aug 22, 2013 9:16 pm
Forum: Beginner Basics
Topic: TRUNK, VALN CCR and CISCO
Replies: 8
Views: 4494

Re: TRUNK, VALN CCR and CISCO

I did not check the work of mikrotik and сisco together, so I can only assume. You can see the traffic on each interface in its properties (in Winbox choose "Interfaces" and then double-click on the desired interface to the last tab will be traffic statistics through this interface). Or in the conte...
by ivtts
Thu Aug 22, 2013 12:08 am
Forum: Beginner Basics
Topic: TRUNK, VALN CCR and CISCO
Replies: 8
Views: 4494

Re: TRUNK, VALN CCR and CISCO

You can assign the address to the interface in such a way, e.g.: /ip addresses add address=10.0.0.1/24 interface=bridge-vlan2 Similary in Winbox (IP -> Addresses, then "+"). To access to your mikrotik device over this interface check your firewall settings (IP->Firewall) and routing table (IP->Route...