MikroTik

MikroUser

Problems with sfp was not fixed.
Tested on a rb5009 and ccr2004. after update no optical link. only phisical reinsert sfp module solves the problem.

we need sfp powe reset option. add please.

MikroUser

Somebody from MT team can reply here? Feature will be added in the future, or here is only hardware solution and only for future models?

MikroUser

Hi, i have many devices who uses chinese SFP onu modules, RB4011, CCR2004, etc.. modules works fine, no issues detected till i dont want update firmware After update routeros - optical link cannot be established. Solution - phisically remove the module and insert again, reboot mikrotik doesnt help, ...

MikroUser

update. everything works now as needed. i have just reboot Mikrotik, after that for Starlink interface was assigned dynamic addres via RA. This is 100% tested and working config for IPv6 & Starlink! Tested on CCR2004, ROS 7.7 /ipv6 address add address=::5 from-pool=StarLink-IPv6 interface=LAN /i...

MikroUser

/ipv6 dhcp-server add address-pool=StarLink-IPv6 disabled=yes interface=StarLink name=server1 /ipv6 address add address=::7 from-pool=StarLink-IPv6 interface=LAN add address=2a0d:3344:1e00:2749::fff1 advertise=no interface=StarLink /ipv6 dhcp-client add add-default-route=yes interface=StarLink pool...

MikroUser

Also if configuration will be successful, this will be a good example for other users. Reddit already has a validated base config: https://www.reddit.com/r/Starlink/comments/xv2p04/starlink_ipv6_config_for_mikrotik_routers/ It seems that IPv6 connectivity is still very much a regional thing as some...

MikroUser

Change your pool prefix length to /64 on the DHCPv6-PD client Then add an address on the LAN bridge or interface like this: ipv6/address/add from-pool=StarLink-V6 advertise=yes interface=LAN Not working. Till gateway is unknown or not reachable - any configuration will fail. The Mikrotik implementa...

MikroUser

I tried different pool prefixes, but no result. And logically, server address (gateway) cannot be accessible from provided prefix pool, because gateway must be somewhere in a provided prefix, usually this is 1st host. Starlink dhcp doesnt send address for the interface, prefix only. And this isue i ...

MikroUser

Mikrotik team, i need your assistance. Starlink is connected via adapter directly to mikrotik. Bypass mode enabled. IPv4 woks fine, but i have problems with ipv6. Starlink give ipv6 from dhcp with 56 prefix. prefix is 2a0d:3344:1490:1700::/56 default gateway received via dhcp is 2a0d:3344:1400:baee:...

MikroUser

I dont know providers who give ipv6 by default, this is option in most cases.

Its depends from country. In Ukraine even LTE, 3G providers give ipv6 to the client phones by default.

MikroUser

If other devices works fine, and laptop connected to mikrotik dont have any isuses with internet connection - this is not Mikrotik problem, this is unifi problem. You can log in to your unifi via ssh and get view logs, and see what is happened when your device lost connection.. If iphone shows wifi ...

MikroUser

Regarding the pings, I am not pinging my own router - I am pinging a public server, so that only works as long as I put in valid address configuration and route/gateway. Maybe I wasn't clear on that. I can see the right packets leaving the Mikrotik on the WAN interface, and replies coming back from...

MikroUser

Your getting ping replies because that ip in your network \ your router. You can set any ipv6 address and always will got ping reply and RA will work. But if provider dont allow your ips - they will not work. And ping from external ipv6 can be not avilable. IPv6 addreses assigned manually or with Ad...

MikroUser

I think your config is wrong, because provider doesnt allow you to use :d01: etc. So, correct config must be like this 1. set for ISP wan interface adddress 2a00:1234:5:d00::2/56 2. set gateway 2a00:1234:5:d00::1 3. set address for lan 2a00:1234:5:d00:2::1/64 and allow adverstie. after that ipv6 in ...

MikroUser

because you are using ipv4 dns,
try set first dns - ipv6, second dns - ipv4

im using cloudflare ipv6 dns: 2606:4700:4700::1111

MikroUser

You can ask your provider for enabling ipv6, or try use ipv4-to-ipv6 tunnel, its free here https://tunnelbroker.net

MikroUser

nslookup 8cb691e535702e64106a3948d54b901798889ee3.ipv6.cws.conviva.com Name: 8cb691e535702e64106a3948d54b901798889ee3.ipv6.cws.conviva.com Addresses: 2620:10b:7001:10::106 2620:10b:7002:14::108 2620:10b:7001:10::109 2620:10b:7002:14::107 domain 8cb691e535702e64106a3948d54b901798889ee3.ipv6.cws.conv...

MikroUser

C52iG-5HaxD2HaxD-TC-US this is us model. Made or assembled in USA, not in china.
But next question - why they sale it in alibaba

MikroUser

This is very old topic, but il try to answer, maybe its will be useful for someone. All android devices (starting from android 4 up to android 13) have this problem. And its very strange that google dont fix it yet. Maybe ipv6 isnt very popular yet When android device receive first ipv6 address from...

MikroUser

Hi, in Ukraine celluar provider Kyivstar start give ipv6 for all clients, but after that all SXT LTE devices stop working. To get them work again need go to the APN settings and change IP Type from Auto to IPv4, or IPv6. If Auto set - lte interface doesnt receive any IP from celluar provider. If is ...

MikroUser

Try test speed by conecting cable from provider directly to laptop, because this may be not a RB5009 problem.

MikroUser

/ip firewall nat
add action=masquerade chain=srcnat dst-address=192.168.88.0/24 src-address=\
192.168.88.0/24 to-addresses=192.168.88.0/24

This rule looks very strange.

MikroUser

I found out why I have the double dps. It seems my NAT rule in not perfectly working...

Speedtest use multiple connections for test, so i dont see something unusual at your screen. Try test with single connection

MikroUser

Try turn off fasttrack if enabled.

MikroUser

Better call to your provider support and ask, this is mikrotik devices forum, but not provider.
I dont know providers who give ipv6 by default, this is option in most cases.

IPv6 can be provided with RA, or in manual mode (provider send you ipv6 adrreses alloved to use).

MikroUser

If you changed main Mikrotik password before, terminal will ask new password. You need close winbox and log in again.

MikroUser

LTE operators dont provide public IPs, or you have special contract?

MikroUser

If you have mac os, then u can try install wine and run netinstall.exe
winbox works fine with wine

or cli version for linux https://download.mikrotik.com/routeros/ ... 7.6.tar.gz

MikroUser

I think you need this way

https://www.youtube.com/watch?v=BbiPxoYpTy0

MikroUser

Here is the setting for client devices.

MikroUser

Set MTU to 1420
Try use mangle rules to mark routes exacly to wireguard.
Also turn off fasttrack if enabled, in my case fasttrack was a source of all problems with wireguard.

MikroUser

You can setup vpn inside mikrotik, add some mangle and routing rules.
After that VPN always will be online, and your pc connected to the workplace without any additional windows network settings.

But this is little hard to setup for non-advanced mikrotik user.

MikroUser

In 99% of cases, speed is limited by operators at base stations.
So if you dont have any special agreements with carrier, you never see high speeds, even if LHG CAT18 hardware will be used.

MikroUser

Have problems on a CCR2004-16g-2s and sfponu module. Issue shows after firmware update add next boot, no pon link at sfp. SFP is visible and hardware info is ok, but no pon link. So after every firmware update i need get out sfponu and insert it again, only after that pon link is ok. Simple rebootin...

MikroUser

mikrotik, please fix the domain. cannot access for 100+ devices with dynamic ip.

MikroUser

default telnet password for DFP-34G-2C2,

root\Pon521

Thanks, logged in. have you any ideas how to make this sfp work with bdcom olt? I always got GPON State Init State, mikrotik shows link ok, but pppoe doesnt up (

MikroUser

PON LOID and SN can be changed. https://uploads.tapatalk-cdn.com/20190924/5665b11069dee918ee652f6a46b70487.jpg https://uploads.tapatalk-cdn.com/20190924/98fa92cf74fedfefa18dc15a3a78dafb.jpg Enviado desde mi SM-G965F mediante Tapatalk Telnet screenshot https://uploads.tapatalk-cdn.com/20190924/ca052...

MikroUser

2014 year coming!!!

Please add SOCKS5 support to ROS!!!!

MikroUser

problem all metals - pure cooling system. there absolutly no radiators on the atheros chips. They are extremaly hot (ithink more than 100*С) when bandwith goes to 20-40 mbits\s. Thermal sensor in metal is stupid. even outdoor is 10*C , metal just power on - he shows 33-35*C wtf? here 2 pics. 1 pic -...

MikroUser

my metal burn out today(( speed was 40 mbps and board work with it 5-10 mins. after - all leads is off. metal newer come back again. RIP ( for good work of this board you must limit summary bandwidth to 5 mbps for all wireless clients (not for each). script might be not work sometimes. nobody dnot k...

MikroUser

no need to chose interface. leave it blank

need only subnet.

MikroUser

not possible integrate anonymous proxy.

best way - Anonymous VPN + Mangle.

MikroUser

In registration, tx/rx bytes doesn't show properly. In my office AP, I've been backing up data to DVDR today and it only shows my laptop as having used just under 1GB of data when I've used more like 12GB. ROS 6.5. edit: the counter starts over at some point. It went to 1.2GB while I posted this, n...

MikroUser

possible, but you need only radius server\secret and customize hotspot login page and walled garden. Use google, there is many useful information.

MikroUser

For distances more than 20m you need protected cable, like that.

and check the voltage on your routerboard. for me original poe adapter was bad..very bad. and i use ubiquti poe adapter from bullet m2

MikroUser

while (true) do={:local a [/in wi reg get number=0 last-activity]; :local b {[:pick $a +4]}; :if (b>=2) do={[/system reboot];};}

this script is the solution for wireless down.
run with sheduler every 2-3 minutes

MikroUser

answer is

:local a [/in wi reg get number=0 last-activity]; :put $a;

MikroUser

???
Please help!!

MikroUser

I have this same problem. Radio sometimes turn's off. Try to run 5.25 6.2 and 6.3 fw!!! think that is not SW problem!

Mikrotik support please answer!!!

1 Year i have Bullet M2HP and there was no problems!

Search found 49 matches