MikroTik

thasser

Please send a screenshot, picture, or more detailed information about the error you are receiving:

For Example:

System Hardware
System OS
Browser Type
MT Router Type

Thanks and good luck, we are here to try and help!

thasser

This writing to the log file, although minute, causes some CPU power. If this were exploited it could make one of our devices more vulnerable to a DDoS attack than if it were not logged, correct?

thasser

The exact same configuration is now working on the legacy SXTac and no issues whatsoever. What is going on here, product released to market before full testing complete????!!!!!?????? PLEASE FIX THIS MIKROTIK!!!!!!! Either fix this or pull the product from the market - it does not work! I have done...

thasser

The exact same configuration is now working on the legacy SXTac and no issues whatsoever. What is going on here, product released to market before full testing complete????!!!!!?????? PLEASE FIX THIS MIKROTIK!!!!!!! Either fix this or pull the product from the market - it does not work! I have done ...

thasser

Hello Everybody, To confirm, is this issue also a problem with wireless 'ARM' based Mikrotik devices operating in Station' mode too? EG: Do you still have the same issues with Mikrotik MIPSBE devices operating in 'AP Bridge' (Access Point) mode and the ARM devices operating in 'Station' (Client) mo...

thasser

Can someone with some sort of authority acknowledge this? I may have missed it but this is a big deal. Is this a known issue or am I crazy??? Traffic is being looped back for some reason - this can cause MAJOR network issues and will create an incredibly unstable network. What do you recommend your ...

thasser

Upgraded one 3011 for tests, IPSEC diff: - 6.42.7 - 50% CPU and 6 to 7 MB/s - 6.43.1 - 40% CPU and full 10MB/s ( max bandwidth ) we will test it with smth like 1gbps/1gbps for lolz :) For now working ok, we will see tomorrow... AWESOME more test results and specifics on config/type of vpn/encryptio...

thasser

Someone tested in NV2 how is working the RBDynaDishG-5HacDr3 which is 802.11ac but has MIPSBE? :? Has anyone tested the newer RouterOS with these higher versions? Does NV2 link work normal? Also, I find it odd that nstream would work and NV2 would not given that NV2 is short for "nstream versi...

thasser

Someone tested in NV2 how is working the RBDynaDishG-5HacDr3 which is 802.11ac but has MIPSBE? :? Has anyone tested the newer RouterOS with these higher versions? Does NV2 link work normal? Also, I find it odd that nstream would work and NV2 would not given that NV2 is short for "nstream versi...

thasser

I am having this same issue with a PTP link with two of the new SXT ac square units. We have simple bridge to station bridge setup with wlan and eth bridged together. No traffic would pass through link on NV2. When I upgraded to 6.43 suddenly the link began to pass traffic through and work, but now ...

thasser

Normis,

Thank you for fixing this security flaw. In the event of an attack, this command could be devastating to one's critical IT infrastructure.

Good thinking by the ROUTEROS/MIKROTIK TEAM!

thasser

thasser

Moved ~60 boards (CCRs, hAPs wAPs, CRSes, SXTs mostly) to this version - all solid so far..

P.S. five nice comments in a row about version? - this is WITCHCRAFT!!

Maybe we found a new LTS release...

thasser

Updated from 6.32.3 on 1x RB3011 and 2x RB951. Went smooth and noticeable improvements. Great job MT team!

thasser

open the terminal and past this: /interface wireless set [ find default-name=wlan1 ] band=2ghz-b/g/n disabled=no distance=indoors \ frequency=2437 frequency-mode=superchannel mode=ap-bridge preamble-mode=\ short ssid=My Wireless Network wireless-protocol=802.11 /interface wireless security-profiles ...

thasser

Ah ok, so identical MAC addresses. Has anyone else seen this issue? Has anyone else upgraded from 6.32.3 to 6.32.4 with SXT, 2011, Sextant, etc.? My RB951 took it like a champ, dynadish and RB922 both report looping errors and are inaccessible via ethernet. Showing no connection. I can use the netbo...

thasser

I am having issues with upgrading from 6.32.3 to 6.32.4 with both RB922UAGS-5HPacD and RBDynaDishG-5HacD. Both are reporting looping errors, but the Dynadish does not have an IP, so the error does not make sense. [XXXXXXXX@YYYYYYYYY] /ip address> print Flags: X - disabled, I - invalid, D - dynamic #...

thasser

The above mentioned setup will work but you will have to have a seperate wireless SSID for the network being broadcasted off of the 2nd wireless card (the one acting as an AP). It will however give you the fastest speed. What I believe you should be using is WDS. Check it out. Give it a try. You wil...

thasser

Hmm. I could see how grounding could affect your speed but that seems very dramatic just for not having a proper ground. What is your internet speed you pay for? What would be better- plug directly into your modem and run speedtest.net to get yourself a baseline. From there we can start to really se...

thasser

No problem. My fee is negotiable and I request a 75% stake in ownership.

thasser

Are there any plans of MT implementing the Qualcomm QCA 9990 4x4 MU-MIMO chipset in the year 2015? Is there at least any testing going on?

thasser

Can we get some verification here on any type of official MT wiring scheme here?

thasser

Always try to match the polarization on a radio ap's chains with that of the cpe or receiving radio. This is not only good practice but should help with performance and connection strength as well. Good luck!

thasser

First, create and configure all of your vlans with their corresponding vlan id's and set the interface to your ethernet port connected to the switch sending the vlan tagged packets. Once you have all of your vlans configured, create a bridge and bridge the vlans and wireless adapter together. Unless...

thasser

Typically a good signal is around -55 dBm. -60 would be considered "full strength" or just below full strength. Above -65 dBm and you will start to see greater UDP packet loss and lower TCP throughput. Once you get above -75 dBm you can start to have connection issues. This holds true for ...

thasser

Try a basic OSPF config and disable all of your rstp in all bridges. This is how I prefer to solve loop issues.

thasser

@Alessio - Do you have any hands-on experience with 4x4 or higher configs?

thasser

Is there any news on when Mikrotik will be able to get their hands on 4x4 MIMO chips? I know that quantenna makes a 4x4 MIMO solution but I believe Mikrotik buys their chips from Qualcomm. Is there any time table set in place for the release of these higher order MIMO configurations?

thasser

We should start a fight club.

thasser

What were your vlan interface trunk settings. Great post btw - more people need to post good information like this myself included.

thasser

Guys, I am trying to find the best way to do this. I have two, physically separated networks that need to be distributed to the same area. I already have an existing backhaul link with more than enough bandwidth to handle this second networks traffic. My first inclination was to do the following: 1....

thasser

v3.0beta3 does not work at all on my pc. At least on boards with v6 installed - I click connect, it says Logging in, Downloading plugins and then nothing happens - no error message, no winbox window, it just closes. Tested to open a board with routeros v5 - works normally. I have the exact same pro...

thasser

You would assign the IP address to the [private-interface]. Either that or assign the address to the customers gateway device.

To make sure they stay inside their own IP address, create a masquarade rule. Give this wiki a shot: http://wiki.mikrotik.com/wiki/How_to_co ... ome_router.

thasser

Since this AP is running mission critical communications equipment, which version should I update to? Are all bugs fixed in the latest version of ROS and in the latest FW? I inherited this board w/ ROS 6.10 installed and running.

thasser

I have had a few of these recently. I am assuming this is referring to the linux kernal that ROS lives on.

Upgrade? Downgrade? Possibly hardware (doubtful). Any suggestions?

thasser

Is there anything in the works for an NV2 equivalent of 802.11ac?

thasser

Does MT have any NV2 equivalent of 802.11AC in the works. For security purposes we like using NV2 as opposed to the more common 802.11.

Thanks and keep up the awesome work! Gig-e wi-fi here we come!

thasser

The 750UP's are all on the same L3 subnet. They are in between the radios and the main switch as shown in the diagram. I would like to have a dynamic routing protocol in place like OSPF but I wanted to ensure that was ideal for this scenario. I was not aware that you can create a mesh with only swit...

thasser

Only ports from the same switch group may be master/slave ports. So I could set ports 3,4,5 as a slave to port 2. The purpose of this setup is to create a added redundancy to this system. At some point or another, one of the RB750UP's will die. When this happens I want to ensure that the network wil...

thasser

I have 3 radios that are all part of the same network. These all are powered/routed by a single RB750UP. My goal is to expand this setup to each radio having its own RB750UP in the event that one of the RB750 switches fails. I have migrated one other RB750UP and it keeps dropping 3-4 pings at a time...

thasser

How would you like me to post my settings? supout?

thasser

Alright here is my current problem: I have an AP (RB911 5 GHz) and it is powered by a RB750UP switch. We monitor our connection status via pings and log each ping response that is sent/received by the device. My issue is that when the AP is connected through the switch it will drop 4-5 consecutive p...

thasser

Alright guys, This one should be kind of fun and pretty simple. So I have two seperate networks at an industrial site. I can not technically bridge them for legal reasons (The states property here is not allowed to be connected to the internet). Lets say network A and network B. I have a RB411 on ne...

thasser

Has anyone heard of or does anyone know of any manufacturers planning on making a 900 MHz 2x2 MIMO mini-pci card that could be stuck into an RB411 or similar MT board?

thasser

It would be really awesome if MT offered a mini-pci-e card for 900 MHz 2x2 MIMO. I would rather deal with MT any day over UBT!

thasser

Lets bring this post back to life: Any DIN-RAIL mountable RB411 enclosures that we know of, checking mfm....

thasser

Have you tested your cable? If not you are using a 24V PoE power injector, correct? When it is connected and communicating at the 10Mbps speed you can go to System -> Health and it will show you your voltage. Anything above 20V is "OK" in my opinion. 40m is well withing the range of a STP ...

thasser

Honestly, I would LOVE for MT to deploy some DIN rail mountable solutions, but we do not seem to be the primary customer base. (Still would be nice though!). Anyways, if you are looking for the latest and greatest, the projects we have we implement a Siemens Scalence series X300 (I believe) switch t...

thasser

LLDP needs to be supported!

Could this even make MT's work with standard 802.3at/af PoE devices since it broadcast its power requirements (is voltage part of the information?)?

thasser

How about this, does anybody know of any passive/24V power injectors that are preferably DIN rail mountable? They all seem to be 802.3af.....

thasser

Sorry for the late reply. What is your status here? You should still be able to winbox into your RB951 via a mac winbox logon, does it not show up in winbox at all, even when trying ports 1-4? Also, I am not sure of your exact configuration needs, but it seems you want to make port 5 into a gateway/...

thasser

Does anyone know if this has been attempted yet? I love using the RB750UP in particular but am having trouble finding a DIN dail or industrial grade mountable box for this instead of the plastic box it is in. Just wondering!

If not, whats your favorite industrial switch/PoE brick?

thasser

riocities, I would suggest using the winbox gui. This should be easily implementable on the RB9XX series. What I believe You would need to do is remove all settings from your router, AKA reset to factory defaults and reboot. From there you will remove configuration (pop-up window on first logon) whe...

thasser

Hello Guys, I believe this should be pretty straight forward but I wanted to make sure I was headed in the right direction. Here is my current set-up. I have a PTP, direct connection to a building where our main server is which has a vpn to a proxy that will allow internet. This proxy must be for se...

thasser

And lastly:

thasser

Went ahead and switched to 802.11 and saw all of the advanced options appear, so I went ahead and set them as well. We are now hovering around -60 dB and back on a 20 MHz channel. I will let you know how the connection holds up. The implementation here has never been done, especially in this environ...

thasser

I am still losing some ping here. I do have only a PTP where my receiver is on top of our temporary office receiving from another radio about 500 meters away. I will try your suggestions one step at a time. I especially like the offset freq. since this is a temporary office as well. Thanks for your ...

thasser

Per wirelesswaves request, here are my new signal results. We will see how long we can keep constant communication. Summary: Back to 10 MHz (5 MHz throughput maxed out at about 4/5 Mbps, true throughput via bandwidth test-tcp one way). Changed antenna power setting to 18 dBi. See attached.

thasser

wirelesswaves,

Thanks for the suggestion, I think you may be correct, the signal is very, very strong (see attached). I will try what you suggested. And report back. For now here are my results with the PTP @ 5 mhz channel bandwidth.

thasser

Hey Guys, So here is my problem: I have two RB911 boards connected to 2.4 GHz itelite antennas. My signal strength is around -33/-32 dBm between the two antennas (~0.5 km apart) plus a 90+% CCQ RX/TX, so there is a very good signal. I am using RouterOS 6.4, nv2, 20 MHz wide channels, with Adaptive n...

thasser

Hello all, At first (as always) I wanted to blame the board but after seeing this issue occur on more than one device I believe it may be a setting. For some reason, and I can not yet find a common pattern, I have a 2x PTP RB911G-5HPnD boards mounted inside itelite's panel 5 ghz daul band antennas. ...

Search found 60 matches