The earlier post was the config from the RB951G. This is from the hAP AC. # feb/18/2016 18:55:07 by RouterOS 6.34.1 # software id = XBHK-BJL8 # /interface wireless security-profiles set [ find default=yes ] supplicant-identity=MikroTik add authentication-types=wpa2-psk eap-methods="" manag...

Thanks for looking into this! My wireless config is: /interface wireless security-profiles set [ find default=yes ] authentication-types=wpa-psk,wpa2-psk eap-methods="" \ mode=static-keys-optional supplicant-identity=MikroTik \ wpa-pre-shared-key=123456789012 wpa2-pre-shared-key=1234567890...

Just got hold of a few hAP AC units. Very excited to see the product. The range of 2.4GHz appears to be far more limited than RB951 that I am currently using. Devices at the far end of my premises are getting a 11dbm weaker signal (-67dbm vs -78dbm), which has rendered the device unsuitable for my p...

You might want to select a larger subnet for your intranet and use it for your DHCP pool - e.g. 192.168.0.0/16 instead of 192.168.0.0/24 that you might be using.

Regards,
Pradeep

Here is how I enabled WPA2 Enterprise with Radius. Using Winbox - 1. Go to Wireless->Security Profiles. Create a new security profile. a. Under the General tab, select Mode=dynamic keys, Authentication Types - only WPA2 EAP (deselect WPA PSK and WPA2 PSK), Unicast Chiper - only aes ccm, Group Chiper...

I have 2 RB951G-HnD routers. One is running as a router, with WPA2- Enterprise authentication. I would like the second RB951 to connect to this wireless network as a client, so that I can connect my wired devices to it. i.e. Internet ----> [(a) RB951 Router] ---- wireless wpa2 enterprise ----> [(b) ...

I run RB951G-2HnD - I have 2 WANs and have configured Failover, which appears to work fine. I also run a VPN for accessing specific IPs (Services like Netflix) that are throttled by my ISPs. I have some devices that need to go via VPN for all Internet Access - have segregated them via LAN IP. Howeve...

I set a firewall mangle rule to place a routing mark on all connections going from the router to the PPTP Server, and routed that traffic via ether2. I am still seeing disconnects... I have verified that I am configuring the Mikrotik PPTP client properly by trying out a StrongVPN server - the PPTP S...

I'm facing a problem where my Mikrotik PPTP client disconnects from my ISP's PPTP server exactly 51 seconds later after getting connected (and keeps connecting and disconnecting). I think I've found the problem, but not the way to fix it - I've tried Googling it, but could not find any solution. Wou...

Success! My Mikrotik is back in working condition!! Thank you all RB951G2HnD, Thank you so much for your guidance. Dallen, You gave me the most important ingredient - hope... Mikrotik support just left me hanging with "Use NetInstall". But hearing your story made me try try and try till it...

Thanks! I did try that. The router remains dead. The ACT Light blinks a few times on powering on, with the reset PIN pressed. Then there is a beep, and then the same status - no wifi, no response from any interface. Have also tried disabling the firewall and AV and tried with Winbox (Port 2) as well...

Just got a new RB951G-2HnD today. Downloaded and copied routeros-mipsbe-6.5.npk to the root folder using Winbox, and rebooted the router by power cycling. When I power on the device, it does beep. When I connect an Ethernet wire, the corresponding light comes on, and the computer identifies the link...

I have a RB750GL. I have 2 WANs. One is a FTTH 60MBPS with PPTP and the other is a ADSL 8MBPS with PPPoE. I am just a beginner and not very experienced in Mikrotik. I can read tutorials and follow them, but when it comes to IP Tables, I am not good enough to create my own rules that work. I know tha...