Upgraded a RB600 to 4.16, and replaced an Alfa card with a r52hn with new pigtails all round, clients have good signal to the new card, but pppoe sessions don't seem complete or last long if they authenticate, completely reset the the card twice and re-setup from scratch, still same problem, Put bac...
I am currently using sstp on 5beta6 and everything runs smoothly, apart from the small memory leak, it works 150% better than my OVPN tunnels which i ran between my rb450's
Got a RB600 that tels me ROUTER HAS NO SOFTWARE KEY ------------------------------------------------------------------- Your router does not have any valid key. Please, get valid key from www.mikrotik.com and enter it at "System | License". If you already have paid for this license, please...
Okay, just to make it a bit more interesting, i am not making use of eoip tunnels, i have a lan connection between 2 routers. MMM MMM KKK TTTTTTTTTTT KKK MMMM MMMM KKK TTTTTTTTTTT KKK MMM MMMM MMM III KKK KKK RRRRRR OOOOOO TTT III KKK KKK MMM MM MMM III KKKKK RRR RRR OOO OOO TTT III KKKKK MMM MMM II...
i also have the same symptoms, also replaced everyting and the SR2 card twice, then replaced it with 8602 card, The 8602 card gives high ping times to clients, so i think the solution is to add a second AP on the board and split up the clients, because im running 60+ clients on one ap. I reckon this...
I had the same problem with 2 differnet sr 2 cards, clients came back up for about a day then disconnect, I then have to disable and enable the card about 50 times then the clients started coming back, I even replaced the card with new one and same problem, then earthed the card to the tower, though...
I have this problem, i have a remote mikrotik connected to ISP with static ip's, the ISP does not allow smtp relaying over the connection, so created a l2tp vpn to my server just for mail, i need to switch of natting, but as soon as i switch of natting (masq) email works and no http, if i switch nat...
Hi I have a l2tp connection to one of my remote mikrotiks i need to relay smtp traffic through the l2tp connection so i made a dst-nat rule to my smtp server All static routes are loaded, as soon as I dissable the masquerading on the remote mikrotik the mail works but no internet, and a soon as I en...
Changed power to 48volt, router ran for an 1 hour, then rebooted, now it keeps rebooting every 2 minutes with no error in the log when it comes back up :?: any ideas. :?: Config : Routerboard 532 (Replaced Yesterday) Daughterboard 564 2 x Sr2 Cards 2 x R52 Cards 48 volt psu unit 2 x 27dbi 5.8 grids ...
This seems to be a power issue, the reason for this is if I disable the the 2 sr cards and the other r52 card the router runs fine,so im gonna take out the poe and give it straight power and see what happens
I have changed the routerboard on that specific site, was running fine for about 45 minutes then same error again, updated to latest routerOS and same problem, haven't updated firmware as yet.
OK upgraded firmware to 2.6 on routerboard and still same problem
The problem seems to be the R52 cards on the backbone links, as soon as there flows data n get ping time outs from the interfaces, and after a few minutes it comes back.
Latest RouterOs loaded 2.9.40, after reboot no wireless devices found, so rebooted again with antennas disconnected and wireless devices were there, so i connected the antennas up one by one and still running, too scared to reboot. Config Routerboard 532 Daugtherboard 564 2 x R52 Cards Running 5 ghz...
You need to add static routes of all the different subnets after the mikrotik to tell it where to go, aswell there needs to be static routes of all the subnets on your linux box if you want internet accros those subnets Here is an example of my mikrotik [admin@HQ] ip route> print Flags: X - disabled...