Community discussions

Search found 66 matches

by paolopoz
Fri Mar 22, 2019 4:24 pm
Forum: RouterBOARD hardware
Topic: RB2011L-IN USR LED
Replies: 2
Views: 271

Re: RB2011L-IN USR LED

No, it's totally blank.
I am using the default configuration.
Also, the wiki says that on RB2011 it's not possible to change the LEDs behaviour.
by paolopoz
Fri Mar 22, 2019 1:38 pm
Forum: RouterBOARD hardware
Topic: RB2011L-IN USR LED
Replies: 2
Views: 271

RB2011L-IN USR LED

I have this old RB2011L-IN which I just changed the power supply because the previous one was dead. I reset it and upgraded it to the last version (6.43.13), checked all ports and found that when I connect ether5 the USR LED starts blinking the same way as the traffic LED of ether5. This happens onl...
by paolopoz
Tue Feb 12, 2019 6:48 pm
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

Hi, i am trying to do basically the same thing but not working. I have 2 routerboards. Server RB1100AHx2 - vpn server Remote site RBSXTR - 3G router Connected via VPN and connection between is OK. But now i have device behind remote router and i can not access it. What was the solution that you had...
by paolopoz
Wed Jun 13, 2018 11:38 am
Forum: Announcements
Topic: Winbox 3.14 released!
Replies: 77
Views: 25300

Re: Winbox 3.14 released!

Hello all! Since today I stubmled upon a problem with Winbox 3.14: every time I try to connect to a host beyond NAT, the application get stuck saying "Downloading descriptors" and then it crashes. This happens also on another PC on my LAN with winbox 3.14. If I try with version 3.13 everything works...
by paolopoz
Fri Jan 26, 2018 10:49 am
Forum: General
Topic: SNTP client, unable to synchronize time, error: server-ip-mismatch
Replies: 24
Views: 4369

Re: SNTP client, unable to synchronize time, error: server-ip-mismatch

I doubt this can be caused by some device on the local network, however you test this hypothesis by unplugging the LAN and let the router plugged only to the WAN. Another thing that I suggest to check is the source IP address of the server-ip-mismatch. Is it the one you configured? Maybe those wrong...
by paolopoz
Tue Jan 23, 2018 10:17 am
Forum: General
Topic: External Winbox MGT Access, Transparent Bridge Mode
Replies: 10
Views: 1231

Re: External Winbox MGT Access, Transparent Bridge Mode

I think it's a matter of packet replies, or better: outgoing packets from router.
I am stuck because I can't think of a method to send the packets directly to the gateway from the bridge...
I will ponder about it but if anybody has other proposals they are welcome :D
by paolopoz
Mon Jan 22, 2018 9:52 am
Forum: General
Topic: External Winbox MGT Access, Transparent Bridge Mode
Replies: 10
Views: 1231

Re: External Winbox MGT Access, Transparent Bridge Mode

I'm sorry, my fault. dst-nat is right.
/ip firewall nat
add action=dst-nat chain=dstnat dst-address=WANIPOFCUSTOMER dst-port=8291 protocol=tcp src-address=WANIPOFYOUROFFICE to-addresses=192.168.199.1(bridge IP)
And of course modify the firewall filter rules accordingly, input chain.
by paolopoz
Fri Jan 19, 2018 9:34 am
Forum: General
Topic: External Winbox MGT Access, Transparent Bridge Mode
Replies: 10
Views: 1231

Re: External Winbox MGT Access, Transparent Bridge Mode

You should DST-NAT.
You have to change from the public IP of the customer router to the out of scope IP assigned to the bridge. Make sure to also check the return path.
by paolopoz
Thu Jan 18, 2018 11:38 am
Forum: General
Topic: Little VPN client failover script... Big issue! :)
Replies: 6
Views: 590

Re: Little VPN client failover script... Big issue! :)

/interface l2tp-client monitor VPN1 once do={ :if ($"status"!="connected") do={ /interface l2tp-client set VPN2 disabled=no /interface l2tp-client set VPN1 disabled=yes /delay 20 /interface l2tp-client monitor VPN2 once do={ :if ($"status"!="connected") do={ /interface l2tp-client set VPN2 disabled...
by paolopoz
Thu Jan 18, 2018 11:26 am
Forum: General
Topic: Little VPN client failover script... Big issue! :)
Replies: 6
Views: 590

Re: Little VPN client failover script... Big issue! :)

This way you are monitoring VPN2 only if VPN1 is connected, is that right?

I am setting up a lab, then I let you know.
by paolopoz
Thu Jan 18, 2018 11:14 am
Forum: General
Topic: Netwatch will not ping through VPN interface [SOLVED]
Replies: 3
Views: 484

Re: Netwatch will not ping through VPN interface [SOLVED]

Just troubleshooting a script on another topic:
viewtopic.php?f=2&t=129716

Maybe we can join forces ;-)
by paolopoz
Thu Jan 18, 2018 11:01 am
Forum: General
Topic: Lite5 reboot then script run
Replies: 4
Views: 461

Re: Lite5 reboot then script run

Where do these devices come from? Is it possible they were customised by the reseller?
by paolopoz
Thu Jan 18, 2018 10:52 am
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

This: /ip firewall nat add action=masquerade chain=srcnat Should be more specific, for example add the out-interface otherwise it will NAT everything. You can also put more specific rules before the masquerade, so you are sure the latter will not interfere. To better understand this situations I fin...
by paolopoz
Thu Jan 18, 2018 10:33 am
Forum: General
Topic: External Winbox MGT Access, Transparent Bridge Mode
Replies: 10
Views: 1231

Re: External Winbox MGT Access, Transparent Bridge Mode

I'm sorry, I wrongly assumed that you are also the ISP, so you would be able to add another network on top of the WAN access. You can surely put an IP address in the bridge interface without it being cause of any problem, unless you put the same IP used in that network segment. According to https://...
by paolopoz
Wed Jan 17, 2018 3:35 pm
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

Matching criteria inside the NAT rule.
You know: src-address, dst-address, protocol, etc.
by paolopoz
Wed Jan 17, 2018 3:24 pm
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

Does the packet counter for src-nat rule increment?
If you want to mark packets then you can bind to that packet mark for the src-nat to work.
by paolopoz
Wed Jan 17, 2018 3:04 pm
Forum: General
Topic: Router with ports not working all of a sudden
Replies: 2
Views: 855

Re: Router with ports not working all of a sudden

I had similar issues with SFP on a CCR1072.
Have you tried to disable and then enable the affected ports?
For me it worked.
by paolopoz
Wed Jan 17, 2018 3:02 pm
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

You just put another rule under the dst-nat, this time with src-nat.
You then need to match the packets you already dst-natted.
A rule could be something like this:

/ip firewall nat
add action=src-nat chain=srcnat dst-port=6060 protocol=tcp dst-addresses=192.168.10.102 to-address=192.168.77.1
by paolopoz
Wed Jan 17, 2018 11:06 am
Forum: General
Topic: External Winbox MGT Access, Transparent Bridge Mode
Replies: 10
Views: 1231

Re: External Winbox MGT Access, Transparent Bridge Mode

Can't you just add a management IP address to the bridge and then point to it?
by paolopoz
Wed Jan 17, 2018 11:01 am
Forum: General
Topic: Lite5 reboot then script run
Replies: 4
Views: 461

Re: Lite5 reboot then script run

Check on System > Scheduler if there is any script running at startup, then disable it.

If you are trying to reset the device remember to
system  reset-configuration  no-defaults=yes
by paolopoz
Wed Jan 17, 2018 10:38 am
Forum: General
Topic: dst-nat through VPN [SOLVED]
Replies: 26
Views: 6096

Re: dst-nat through VPN [SOLVED]

NVR needs to know where to send the reply packet, so the router on remote site it should have the gateway through the VPN.
If you cannot do this, you can workaround by src-nat the packet with an IP from the local router (e.g. 192.168.77.1) which is reachable from the NVR.
by paolopoz
Wed Jan 17, 2018 10:32 am
Forum: General
Topic: Little VPN client failover script... Big issue! :)
Replies: 6
Views: 590

Re: Little VPN client failover script... Big issue! :)

Are you using these lines
VPN Interface 1
also into the script or are the commented?

The message "terminating... - administrator request" seems to refer to a VPN that is not working for some kind of misconfiguration.
by paolopoz
Wed Jan 17, 2018 10:22 am
Forum: General
Topic: chain=input action=drop in-interface-list=!*FFFFFFFF
Replies: 3
Views: 477

Re: chain=input action=drop in-interface-list=!*FFFFFFFF

Did you find this rule preconfigured in some router? What version?
What problem are you encountering with this?
by paolopoz
Wed Jan 17, 2018 10:14 am
Forum: General
Topic: Netwatch will not ping through VPN interface [SOLVED]
Replies: 3
Views: 484

Re: Netwatch will not ping through VPN interface [SOLVED]

Netwatch should work also through a VPN. Are you checking an IP which is reachable only via VPN? Please also consider that the ping is generated from the router itself, so NAT and route rules should be consistent. You can also monitor the status of the VPN with a script and then schedule it to run p...
by paolopoz
Tue Jan 16, 2018 4:59 pm
Forum: General
Topic: DHCP server no using all the IPs - some clients cannot connect
Replies: 3
Views: 322

Re: DHCP server no using all the IPs - some clients cannot connect

Are you sure that other IPs are free?
If you want to be sure that the cause of connection not working is the (lack of) IP address assigned, then you should check on the client device.
Usually dhcp-server assign the IPs starting from the highest one (in your case from 200 to 10).
by paolopoz
Thu Jan 11, 2018 5:54 pm
Forum: General
Topic: SNTP client get unauthorized NTP requests
Replies: 4
Views: 523

Re: SNTP client get unauthorized NTP requests

Thanks pe1chl, this is of course some kind of scanning coming from big internet but this is not what I want to point out.

What I mean is: a client should just get back its request, then why do I see incoming packets as if the router was listening on port 123/UDP? This is a server behaviour.
by paolopoz
Thu Jan 11, 2018 5:47 pm
Forum: General
Topic: Help Creation VPN IPSEC [Solved]
Replies: 6
Views: 528

Re: Help Creation VPN IPSEC

If it was working, then there is no reason why it would go slow.
Unless you have added some kind of queues.
Please check CPU and end-to-end latency.
by paolopoz
Thu Jan 11, 2018 5:17 pm
Forum: General
Topic: Help Creation VPN IPSEC [Solved]
Replies: 6
Views: 528

Re: Help Creation VPN IPSEC

You said: The connection it's established but i canno't ping o do other to the Internal IP of the other site which reads as if IPsec tunnel is working but no data is passed on it. So, is it the LAN-to-LAN flowing? Can you reach remote hosts through the VPN? Please check in IPsec > Installed SAs and ...
by paolopoz
Thu Jan 11, 2018 4:56 pm
Forum: General
Topic: CCR 1036 CPU utilization 100%
Replies: 5
Views: 996

Re: CCR 1036 CPU utilization 100%

I guess that you are BGP peering with a ISP or carrier and they are announcing to you the full table (~500k routes). Am I right?
If this is the case, be aware that BGP is a single thread process and it is not possible to make it use the multi-core architecture.
by paolopoz
Thu Jan 11, 2018 4:51 pm
Forum: General
Topic: SNTP client get unauthorized NTP requests
Replies: 4
Views: 523

SNTP client get unauthorized NTP requests

I have some routers with SNTP client (the built-in one) enabled and working. Some interfaces has public IP addresses but I don't have any firewall rule configured because I want to use FastPath. Checking SNTP client status I often see this: last-bad-packet-from: 162.209.xxx.xx last-bad-packet-before...
by paolopoz
Thu Jan 11, 2018 1:11 pm
Forum: General
Topic: SNTP client, unable to synchronize time, error: server-ip-mismatch
Replies: 24
Views: 4369

Re: SNTP client, unable to synchronize time, error: server-ip-mismatch

Did you get it working?
If you need help with NAT config just drop a line.
by paolopoz
Thu Dec 07, 2017 1:31 pm
Forum: General
Topic: Help! 3 Vlan for two mikrotik rb750
Replies: 1
Views: 317

Re: Help! 3 Vlan for two mikrotik rb750

Hello! First, this task will be better suited by a switch with VLAN capabilities, you don't really need a router to do this. If you want to solve this situation with this hardware you need to use bridges between ethernet ports and GRE or EoIP tunnels. So that you must have: [ether1--bridge1--gre-tun...
by paolopoz
Tue Dec 05, 2017 12:55 pm
Forum: General
Topic: denied winbox/dude connect from x.x.x.x
Replies: 3
Views: 2683

denied winbox/dude connect from x.x.x.x

Hello all! In 6.39 changelog I see that: *) log - added warning when Winbox/Dude sessions were denied; But I didn't expect it to work it even if /ip service rule do not allow access to winbox port from that specific IP. I think that this kind of logs must not be generated if the port is unreachable ...
by paolopoz
Tue Dec 05, 2017 12:40 pm
Forum: General
Topic: CCR1009 IpSec site-to-site with Checkpoint R77.30
Replies: 2
Views: 1196

Re: CCR1009 IpSec site-to-site with Checkpoint R77.30

Check all the timing in phase2 (proposal) and phase1 (peer), they must be equal on both sides. Also set NTP client on both endpoints with the same server, so that they are as much in sync as possible. Some FWs have more re-keying options than time, such as amount of data. Be sure to disable them and...
by paolopoz
Fri Sep 15, 2017 3:44 pm
Forum: General
Topic: FastPath interface counters and global counters
Replies: 4
Views: 898

Re: FastPath interface counters and global counters

Thank you strods for explanation.
However in my case I also have packets incrementing in output.
I attach an excerpt from a screenshot to better explain.
fp-eth.PNG
Is it the same behaviour of counting also for Tx packets?
by paolopoz
Fri Sep 15, 2017 3:33 pm
Forum: General
Topic: Slow routing with a CCR1009
Replies: 11
Views: 1728

Re: Slow routing with a CCR1009

Could it be a faulty rate limit on ISP side? Try add a simple queue a bit below the max bandwidth of the link, to see if it's any better. Maybe the old ASA had some rate limit configured in it. Also, if you have access to it, try to compare the configuration of interfaces. I rule out a hw problem as...
by paolopoz
Fri Sep 15, 2017 3:23 pm
Forum: General
Topic: FastPath interface counters and global counters
Replies: 4
Views: 898

Re: FastPath interface counters and global counters

Thanks andriys,
I forgot to mention: neither Fasttrack is enabled under /ip settings and stats are empty.
I only have a bridge as a loopback with no ports configured, so that cannot be the source of that packets, in fact those stats are empty.
by paolopoz
Fri Sep 15, 2017 1:25 pm
Forum: General
Topic: FastPath interface counters and global counters
Replies: 4
Views: 898

FastPath interface counters and global counters

Hello all.
I have a router with 6.40.3 where I can see FP counters incrementing on both Tx and Rx on some interfaces, while if I check under IP Settings I see that FastPath is not active nor the counters increment.
Are those packets using FastPath on those interfaces or not?
by paolopoz
Fri Aug 25, 2017 11:34 am
Forum: General
Topic: PPPoE MSS clamp no working on upgrade
Replies: 17
Views: 5124

Re: PPPoE MSS clamp no working on upgrade

Did you find a solution?
by paolopoz
Tue May 16, 2017 7:01 pm
Forum: Forwarding Protocols
Topic: Routing another IP All traffic
Replies: 1
Views: 339

Re: Routing another IP All traffic

Isn't adding a static route just enough?
/ip route add dst-address=192.168.2.0/24 gateway=192.168.1.253
Else, if you need to redirect to the Cisco only the traffic coming from 192.168.1.0/24 you need a routing mark
by paolopoz
Tue May 09, 2017 10:21 am
Forum: Forwarding Protocols
Topic: [Solved] OSPFv2 neighbor x.x.x.x: state change from Full to Down
Replies: 9
Views: 5972

Re: [Solved] OSPFv2 neighbor x.x.x.x: state change from Full to Down

PowerBeam M5 on one side and Rocket M5 on the other.
by paolopoz
Tue May 02, 2017 4:12 pm
Forum: Forwarding Protocols
Topic: [Solved] OSPFv2 neighbor x.x.x.x: state change from Full to Down
Replies: 9
Views: 5972

Re: OSPFv2 neighbor x.x.x.x: state change from Full to Down

Thank you all.
By setting the OSPF neighbor to NBMA I fixed the problem!
by paolopoz
Tue May 02, 2017 4:10 pm
Forum: General
Topic: Huge performance drop with mangle + queue tree rules, CPU 50% max
Replies: 22
Views: 4608

Re: Huge performance drop with mangle + queue tree rules, CPU 50% max

@ivicask: what others are saying is that in multi-cpu boards (like your hEX or my CCR) some processes that don't use multi-threading can consume a single core to 100% but what you see in total (that one you see in winbox) is a fraction of percent. Given that you have a dual-cpu system, if one goes t...
by paolopoz
Tue May 02, 2017 3:08 pm
Forum: General
Topic: Huge performance drop with mangle + queue tree rules, CPU 50% max
Replies: 22
Views: 4608

Re: Huge performance drop with mangle + queue tree rules, CPU 50% max

On a different scenario but I have the same problem. Many simple queues on a CCR1009, CPU is fine (<50%) but throughput is really limited. Disabling queues makes it flow without issues.
I don't know what to do.
by paolopoz
Mon Apr 10, 2017 11:03 am
Forum: Forwarding Protocols
Topic: BGP advertisements
Replies: 3
Views: 623

Re: BGP advertisements

Check in BGP instance what it's redistributing.
by paolopoz
Mon Apr 10, 2017 11:01 am
Forum: Forwarding Protocols
Topic: OSPF confusion
Replies: 4
Views: 712

Re: OSPF confusion

I second idlemind: path cost is the way to go. You can also take advantage of Equal Cost Multi Path (ECMP) from OSPF: if a router sees two paths with same total cost it will equally distribute the streams in both links. However keep in mind this is working only for new data streams, so it will take ...
by paolopoz
Thu Apr 06, 2017 11:13 am
Forum: Forwarding Protocols
Topic: [Solved] OSPFv2 neighbor x.x.x.x: state change from Full to Down
Replies: 9
Views: 5972

[Solved] OSPFv2 neighbor x.x.x.x: state change from Full to Down

Hello! I have 2 routers with OSPF neighboring over a radio link (Ubiquiti). It happens that the link state goes randomly down even if the radio link is always up and running. Both routers have been upgraded to 6.38.5. One is a CCR1009, other is a RB2011. CPU resources are within good margins. OSPF n...
by paolopoz
Thu Apr 06, 2017 10:51 am
Forum: Forwarding Protocols
Topic: OSPF Scalability
Replies: 2
Views: 556

Re: OSPF Scalability

Another common solution would be to use BGP over OSPF. You let OSPF manage the reachability from a router to another, then route all the customers prefixes with BGP which is lighter on updates. You only need a centralized BGP route-reflector (better two), it can be an existing router. In this way we...
by paolopoz
Fri Oct 07, 2016 4:35 pm
Forum: General
Topic: Feature Request: RP filter per interface
Replies: 1
Views: 895

Re: Feature Request: RP filter per interface

I second that!
This is a fundamental feature to provide connectivity to customers while keeping the internet a good place.
Given the continous rise in DDoS attacks we as providers have the responsibility to do this kind of checks and I know that MikroTik understand its role in this. :wink:
by paolopoz
Wed Aug 03, 2016 7:04 pm
Forum: Beginner Basics
Topic: Mikrotik to Watchguard M200 firewall IPSEC VPN
Replies: 1
Views: 1911

Re: Mikrotik to Watchguard M200 firewall IPSEC VPN

Late reply...
I successfully configure IPsec tunnels between WatchGuard and MikroTik, they all work (almost all on first try) and pass traffic.
You have to exclude IPsec traffic from NAT (ip > firewall > nat). Add a rule with action "accept".
by paolopoz
Mon Aug 01, 2016 1:28 pm
Forum: The Dude
Topic: The Dude, v6.36 [current] release.
Replies: 48
Views: 11721

Re: The Dude, v6.36 [current] release.

Good job!

However a nice feature which is now lost was the fact that log messages were colour-coded for up or down events. Now it's all black and it's less easy to spot up/down events.
It would be great to have this feature back.
by paolopoz
Wed Jul 20, 2016 6:59 pm
Forum: General
Topic: Log flooded with SNTP time changes - since latest F/W releases
Replies: 8
Views: 933

Re: Log flooded with SNTP time changes - since latest F/W releases

I have the same problem here, with latest stable release (6.35.4). To me it's software-related as the log lines for sntp aren't anymore classified in topic ntp but fall into the general system and info topics, thus popping up every update. Obviously I don't want to disable those topics because they ...
by paolopoz
Wed Apr 27, 2016 1:26 pm
Forum: General
Topic: RP Filter logging and counters
Replies: 0
Views: 542

RP Filter logging and counters

I am starting to implement RFC2827 / BCP38 on our network.
I would like to know if the Reverse Path Filter is working, if it generates some logs when a packet is blocked or how to enable it (given that this is under /ip settings) and if there is a counter for these blocked packets.
Thanks!
by paolopoz
Thu Sep 24, 2015 10:37 am
Forum: General
Topic: BUG: 3rd Party Discovery Packets sends CPU to 100%
Replies: 0
Views: 319

BUG: 3rd Party Discovery Packets sends CPU to 100%

This is an incomplete bug report. I write it down the same for future reference or just for someone to pick it up. Case: RB2011 with latest version (6.32.2) with no configuration applied. Connect one port to a live LAN on any of RB ethernet port. After a few seconds the CPU goes straight to 100%, pr...
by paolopoz
Fri Jun 12, 2015 10:44 am
Forum: General
Topic: [SOLVED] Do "Half Fast Path" packets increment counters in /ip settings?
Replies: 2
Views: 463

[SOLVED] Do "Half Fast Path" packets increment counters in /ip settings?

I think the subject says it all.
I want to know it also to evaluate the CPU (un)load of this "half fast path" feature.
by paolopoz
Wed May 13, 2015 1:34 pm
Forum: Beginner Basics
Topic: i am newbie in mikrotik and i have some loop problems
Replies: 7
Views: 2553

Re: i am newbie in mikrotik and i have some loop problems

Are there other switches in the network? Did you connected some of them together using two or more ports of the MikroTik?
Probably the router freezed because of a broadcast storm.
Learn about "Spanning Tree Procol" and then enable it on the bridge configuration, STP tab.
by paolopoz
Thu May 07, 2015 3:38 pm
Forum: Announcements
Topic: RouterOS v6.28 released
Replies: 229
Views: 62038

Re: RouterOS v6.28 released

Slow download speeds BGP prefixes, and uneven loading the CPU.
This is a known limitation: BGP routing table loading is single threaded thus using only one CPU.
by paolopoz
Thu May 07, 2015 12:27 pm
Forum: Announcements
Topic: RouterOS v6.28 released
Replies: 229
Views: 62038

Re: RouterOS v6.28 released

Does anybody experienced problems with wireless disconnections after upgrading to 6.28? I have a PtP link and after upgrading one of the two sides I keep getting disconnections with error: lost connection received deauth class 2 frame received (6) After downgrading to 6.27 the problem disappeared. T...
by paolopoz
Mon Jul 21, 2014 12:08 pm
Forum: General
Topic: Winbox 3 beta
Replies: 243
Views: 119948

Re: Winbox 3

Bugs in Winbox 3: I have a list of devices automatically imported from previous Winbox version. When trying to modify one of these entries by adding to them a group name, those items disappear from the list. Even selecting the specific group in the dropdown menu does not help. It is necessary to clo...
by paolopoz
Mon Nov 04, 2013 3:09 pm
Forum: General
Topic: CCR 1036 interface restart when passing > 460mbit/s
Replies: 7
Views: 1899

Re: CCR 1036 interface restart when passing > 460mbit/s

Here is what happen: booting CCR without any port attached works fine, as soon as I attach the ethernet cable from my notebook to the eth7 the router reboot. Here is what I see on console: Pid: 0, comm: swapper/34, CPU: 34 r0 : 0xfffffe40751d0000 r1 : 0xfffffe00006e99d8 r2 : 0x0000000000002824 r3 : ...
by paolopoz
Mon Nov 04, 2013 1:52 pm
Forum: General
Topic: CCR 1036 interface restart when passing > 460mbit/s
Replies: 7
Views: 1899

Re: CCR 1036 interface restart when passing > 460mbit/s

I upgraded my CCR-1036 from v6.5 to v6.6rc1 but now the router reboot continously shorly after the boot phase.
I will make other tests connecting in console while booting but by now it seems to me that the 6.6rc1 is bugged.
by paolopoz
Thu Oct 31, 2013 6:52 pm
Forum: General
Topic: CCR 1036 interface restart when passing > 460mbit/s
Replies: 7
Views: 1899

Re: CCR 1036 interface restart when passing > 460mbit/s

Same here, with much less bandwidth than 460 Mbps. However I see that the problem is tied with lot of traffic flowing. To me it also happens on more than one interface at once: 16:35:32 system,info filter rule changed by admin 16:35:32 system,info filter rule changed by admin 16:35:45 system,info de...