MikroTik

nerdtron

You should setup wifi Hotspot in Mikoritk.
Then it would be possible to change/edit the default login.html page of mikrotik. It would also be possible to redirect the external login page to a remote server.
Please read: http://wiki.mikrotik.com/wiki/HotSpot_e ... login_page

nerdtron

If you think nat is the problem, you can still run hotspot without the nat. Just make sure that the hotspot interface is the one giving dhcp addresses. Then you be able to see you local network.

nerdtron

My problem too. I hope somebody has a solution.

nerdtron

You can't ping both by default since you can't have 2 default gateways at the same time.

Try adding src-address from your ping.

ping [gateway wan1] src-address=[ip of interface wan1]

nerdtron

This one is very good. Basically, you segment the LAN into two networks, each having their own gateways.
http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

nerdtron

I tried. Once you get over 9 it doesn't work. Is there a special way to enter 24 seconds? Also, does this bog down any resources and slow down the router? Thanks. That's why don't put it on the netwatch. Put the script on System>Scripts and create a scheduler for it to run every 2 minutes. You defi...

nerdtron

Change the interval in 24 seconds and change the "10" to 5, this will spread the 5 pings in 2 minutes.

nerdtron

You guys are confusing me. Can I put these scripts in the up and down area of netwatch, or do they need to go somewhere else? It would be better if you put the script on the System>Script Then create a System>Scheduler for it where you can also tweak on how it start during boot up. On the Scheduler...

nerdtron

OK that settles it.

nerdtron

Why does this have to be so hard. :D Script to check for if the main link is down. This will perform the commands you specified once only when the check fails. :local i 0; {:do {:set i ($i + 1)} while (($i < 10) && ([/ping 192.x.x.x interval=3 count=1]=0))}; :if ($i=10 && [/ip route ...

nerdtron

When it goes up, just write another similar script. Notice the slight difference.

:local i 0; {:do {:set i ($i + 1)} while (($i < 10) && ([/ping 192.x.x.x interval=3 count=1]=1))};
:if ($i=10) do={:log info "Warning: 10 successful pings to IP 192.x.x.x";
/set your command here.}

nerdtron

Script to ping 10 times with an interval of 3 seconds, then execute commands if all pings are unsuccessful. :local i 0; {:do {:set i ($i + 1)} while (($i < 10) && ([/ping 192.x.x.x interval=3 count=1]=0))}; :if ($i=10) do={:log info "Warning: 10 unsuccessful pings to IP 192.x.x.x";...

nerdtron

He probably means "this is not a complain" which means his post is not about a problem he is having.

nerdtron

Reconnect button when connection is lost would be something!

^THIS!
It's not just something, this is a big improvement.

nerdtron

So no one got anything? Is anyone successfully running 6.11 on 951Ui-2HnD? Firmware version? Exactly the same device here. I tried upgrading to 6.11, remove default configuration, then configured Same scenario as yours and the router works properly. Tried to unplug and replug a few times and bootup...

nerdtron

Not a problem at all since ping packets are very small and have low priority.

nerdtron

Unfortunately reaching their web interface is possible only when using the currently active WAN Yup, that would be correct since you don't mark inbound packets, therefore they will be directed to the currently active default route with no routing marks. The solution is to also mark the inbound traf...

nerdtron

Yes, I think you'll have a problem using VOIP, RDP and VPN since they need a fixed connection while PCC will tend to shoot the packets on different wan paths. You can try to change the you per-connection-classifier to source address only or destination address only. Or you can also create dedicated ...

nerdtron

PCC can sometimes be difficult to control and sometimes breaks secure https sites.
I recommend creating two lan or subnets and assign them their own gateway wan.
http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

nerdtron

I am setting up my first hotspot for a local coffee shop and I was wondering if there is a way to make the login page show some terms and conditions and then the user only needs to click an Accept button to continue to the internet. I have been combing the forum but have been unable to find a post ...

nerdtron

/export

Then copy and paste to notepad.
Remove info such as MAC addresses as they will be automatically added.
Paste again on next router.
Done.

nerdtron

This what I followed http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways
Basically, you'll have two LANs each with its own ISP.

nerdtron

hay all i have rb951 6.7 i use hotspot (username & pass) my wan1 ip is 192.168.0.1 i got a new internet line wan2 ip is 192.168.1.1 how to use both this lines in my RB?? can i work with wan1 192.168.0.1 wan2 192.168.0.2 ???? thanks I wouldn't recommend PCC and hotspot combination. It's not very...

nerdtron

I have made load balancing with the help of this instruction http://wiki.mikrotik.com/wiki/Load_Balancing_over_Multiple_Gateways Balancing works fine but I cant access any of LAN devices What is the way out? Remember the part on adding mangle rules for GroupA and GroupB? Chain prerouting and Src. A...

nerdtron

On the login html page, if you find this line: <input type="hidden" name="dst" value="$(link-orig)" /> Change to something like: <input type="hidden" name="dst" value="http://google.com" /> This will hardcode google.com as the redirect page...

nerdtron

I don't really recommend PCC plus hotspot setup, but I guess why not just segment the network into two seperate LANs.
Say 70% of all users will be directed to WAN1 and the other 30% of users will be directed to WAN2. It would be more stable and reliable.

nerdtron

Real life experience from this thread http://forum.mikrotik.com/viewtopic.php?t=54607 Anyway, use cloud core routers for production environments and you don't have to worry for compatibility issues on x86 machines. Plus, router have more ports. Are your routers going to face the public internet to m...

nerdtron

Make sure also that "keep-alive" on the user profile is set to 3 days. So that even when the user disconnects on wifi, it will take 3 days before he is removed on the active queue. Of course, he will be logged out once he request log-out or when radius servers says that the user should be ...

nerdtron

You don't have to complicate things. Just have two separate lan for each network. Then mark each connection and create a default gateway for each routing mark.
http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

nerdtron

You can also add the IP block on the walled Garden IP list so that hotspot users can access the IPs without logging in.

nerdtron

Try uploading the files using FileZilla.
Remember to use port 21 when you connect to the router.

nerdtron

What type of load balancing would you do? If PCC, it is possible, but a bit difficult, not to mention the using multiple gateways can disrupt some https website. It would be better if you create 2 lans, then make gateway 1 as the default route for lan 1, then gateway 2 as the default route route for...

nerdtron

try to use different info/data channel.

How many combinations should I try?
0,0
0,1
0,3
1,0
etc...

So any more ideas?

nerdtron

I have ZTE MF631. PPP interface show that the device is detected, however even after inputting the correct apn and dial settings, it still can't connect. Does Mikrotik support this modem? If so, why is the logs showing "could not acquire serial port"? Please help as we to confirm this imme...

nerdtron

Upgrade to 6.11 and if still not working put "/export compact" command result on the forum (remove sensilble data first) before eventually downgrade. http://www.mikrotik.com/download/share/routeros-mipsbe-6.11.npk [thanks Normis for the link on other thread] Is this the official release? ...

nerdtron

@nerdtron What do you mean exactly? In windows, if your computer has IP 192.168.1.2 and the port you are connected on mikrotik has IP address 192.168.88.1, you won't be able to connect using MAC. Try settings your computer IP to 192.168.88.2 and you'll be able to connect. I know it defeats the purp...

nerdtron

Hi all, I'm too lazy to edit the WIKI but here's the list of dongles I have tested on RB951Ui-2Hnd and RouterOS 6.10 Huawei E1553 Huawei E357 Huawei E173 Alcatel One Touch X230M All are working, although each of them has their own Info Channel and Data Channel. But everything will be detected once y...

nerdtron

On last ubuntu, just download & run winbox (by "Wine 1.4") and all is working...

13.10? How's the terminal font on yours?

nerdtron

Read change log from the 6.7 to 6.10. On my tests, none was lost so far. But I guess it all depends which features are you using that is dependent on the router os version. On my setup, here's what I have used so far and no config was lost. Hotspot Policy routing for 2 gateways PPP client for the US...

nerdtron

It does work fine on mine, but I didn't installed wine using the default installation. I customized a lot of settings on wine. Anyway, I am successful on using the default wine install to use winbox by setting the IP address of the computer on the same subnet of the mikrotik router. Then try connect...

nerdtron

You don't have to complicate things, just mark routing will do the job for you.
Here's the link: http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

nerdtron

Doesn't VPN creates it own interface on the router?
Make this interface your default gateway, and add nat masquerade on that interface. All traffic on your lan will be directed the VPN tunnel and not the DSL.

nerdtron

I'm not quite sure, but I think this has something to do with the lease time of the ip/mac bindings that the dhcp server hands out. I think the default is 3 days, try lowering the value.

nerdtron

No problem!

610.jpg

Finally! Thanks!
I overlooked that part

nerdtron

Screenshot 2014-03-11 15.08.45.png 100 times login ... ;-)). Next update the same procedure ... I would setup TheDude, upload the Image to the Dude and make upgrades with the dude. First time it takes longer as you've to enter password for each device. But next and following updates are done with a...

nerdtron

Screenshot 2014-03-11 15.08.45.png

Donwload 10MB on each mikrotik? I'd prefer to download it and then upload it on each device.

nerdtron

I have about 100 RB951Ui routers and all are on version 6.5.
I want to upgrade them to version 6.10, but i don't know where to get it.
I can download the version 6.9 npk file and do the upgrade, but I can't find the version 6.10

nerdtron

I'm not sure if this is what you wanted, but are you talking about DMZ?
http://forum.mikrotik.com/viewtopic.php?f=14&t=38916

nerdtron

Sorry In which system? Mikrotik, Plat or Freeradius?

When the user fails to authenticate, what is the error on the mikrotik log?
If mikrotik sends the credentials to the radius server, what is the error on the freeradius server?

nerdtron

Try FreeRadius with Daloradius web interface. It will enable you create users and set limit for each users with session-time and data limit.
http://blog.cygnaltech.net/2013/04/inst ... -2110.html

nerdtron

My mikrotik accepted this config. /queue simple add max-limit=5M/5M name=queue1 target=bridge1 Haven't tested it yet but I think it will limit traffic of interface bridge1 with 5Mbps for upload and download. EDIT: Sorry I read it again you want to rate-limit a port that is a member of a bridge? /que...

nerdtron

I can ping the PPPoE interface, ether1 and ether2 from the VPN client, but I can't ping any hosts INSIDE the LAN This is the correct behavior if your mikrotik is the vpn client. You can't access anything inside the LAN behind the mikrotik since all of these LAN devices are behind NAT. The only way ...

nerdtron

The major drawback for me in webfig is that you can't connect using MAC Address. If the router has no configured IP addresses, you can't connect through webfig.

nerdtron

You can include 2 ntp pools for time sync. Isn't that enough? In creating scripts and schedules, go to System>Scripts. Click the plus sign to add an entry. Give it a name (ex: check-time) and then paste your whole script in the Sorce box.Click OK to save. Then go to System>Scheduler. Click the plus ...

nerdtron

Just input the FQDN in the /system ntp
The FQDN will be converted to IP addresses once the router does nslookup.

nerdtron

When you intercept a https page, the browser will definitely show an SSL warning because the page you want to go is different on the login page. This is how https is designed to prevent man-in-the-middle attacks.
You can't have a workaround in this behavior.

nerdtron

What is your session timeout in freeradius?
Also just to make sure that there is no limit on the time, login a user and then view the Active tab on the IP>Hotpspot.
If you see it countdown, then you have a setting for session timeout.

nerdtron

I'm aware that I need to have an SSL certificate on my login page so that mikrotik can successfully redirect login pages. However, even installing the certificate on the website and now that the page is in https mode, users connecting via the hotspot are still getting SSL Error pages. Although once ...

nerdtron

I have successfully followed the tutorial on this link: http://wiki.mikrotik.com/wiki/HotSpot_external_login_page Login page redirect on regular http sites. I'm aware that I need to have an SSL certificate on my login page so that mikrotik can successfully redirect login pages. However, even install...

nerdtron

Hi,
I would like to know If you use an external login page?
I mean, the mikrotik login page redirects to an external https page?
I have a problem of https redirection, I already have an SSL for my external login page.

nerdtron

Activated NTP for the correct time. Still certificates are shown to be valid for only 365 days.

nerdtron

I'll make a compromise on this, especially if you need a reliable connection. (since PCC tend to just throw you on each link)
I'll make half of the LAN clients go to WAN1 and the other half of the LAN to WAN2.
See here: http://wiki.mikrotik.com/wiki/Load_Bala ... e_Gateways

nerdtron

It is possible to redirect https traffic to the login page if you activate the https in the Login tab of the hotspot server profile. But you will need to have an ssl certificate installed on mikrotik.

nerdtron

Hi all, I'm using openVPN with certificates on mikrotik devices. The server is an Ubuntu server. I generated the certificates on the server and uploaded them on mikrotik. When I generated the certificates, they are valid for 3650 days. I tried opening them on windows and it says certificate is valid...

nerdtron

I noticed that whenever I use the ping command in mikrotik, the default packet is 56 bytes. [admin@client2] > ping 192.168.1.27 HOST SIZE TTL TIME STATUS 192.168.1.27 56 56 897ms 192.168.1.27 56 56 337ms 192.168.1.27 56 56 306ms Is there a way to set the default packet size to 32 bytes only?

nerdtron

OpenVPN still works in 6.10 as I have tested. But renaming the certificates in winbox is not working.

nerdtron

You won't see it in speed test because speed test traffic will only flow on one link.
Try downloading torrent and you'll see both link utilized.
Also what are you using as Per Connection Classifier?
both addresses?
both addresses and ports?
src addresses?
Try a different classifier.

nerdtron

What particular settings are you having problems?
I'm using openvpn and routerOS version 6.10 with no issues so far. I'm using certificates too.

Also, try to look at the logs of your OpenVPN server.

nerdtron

I prefer scripts like the netwatch II http://wiki.mikrotik.com/wiki/Improved_Netwatch_II
I also modified it to include a out interface on the ping command so that the ping will always check if connection on that interface is down.

nerdtron

This will help you: http://wiki.mikrotik.com/wiki/HotSpot_external_login_page It is recommend to use a radius server for this. Define an external radius server in mikrotik. Then edit the login.html in mikrotik as the link suggest and then put the external login.php on the server your remote hotspot ...

nerdtron

This will help you: http://wiki.mikrotik.com/wiki/HotSpot_external_login_page Basically solves almost all problems. (you should have a radius server for this, or users defined in mikrotik device) Problem 2 is easily done using walled garden IP list. Then here comes problem 1 and 3. When the user wan...

nerdtron

You should activate the Hotspot feature for mikrotik. It has an option to show and advertisement on a specified time. Say every 30 minutes users browsing the web will be redirected to an advertisement page you have entered on the config.

nerdtron

Its really less complicated than that. All you really need to do is add two default gateways. One will have a higher distance than the other. Both will have Check gateway by ping enabled. Then you will also need two NAT rules. That will work perfectly and without any problems. Yes you can do this i...

nerdtron

Default on mine too is 10 secs. The problem is, on the mikrotik terminal, ping will still have replies when I change the default route. On the computer connected on the LAN, changing the default route will stop the ping replies. I need to issue another ping command to have replies. I'm looking to re...

nerdtron

I think that's working as intended.
I don't know how's Cisco working, but you can do the same with MT.

Yes I'm trying to find out how to do it in mikrotik. Can you point which settings should I look at?

nerdtron

Maybe connection tracking?
/ip firewall connection

I tried changing the timeouts to 10 seconds. It marks connections as timeouts but the behavior of continuous ping on the client computer still stops.
Can you elaborate on how to change settings here?

nerdtron

Just a single LAN IP block on all lan ports, all lan ports are on a single bridge interface. I declared my lan on an address-list. /ip firewall address-list add address=192.168.1.0/24 list=lan-users Then declared NAT for each interface. /ip firewall nat add action=masquerade chain=srcnat out-interfa...

nerdtron

I have been using cisco devices in the past and I haven't faced this problem until I used mikrotik. Say I have: LAN: 192.168.1.0/24 WAN1 gateway: 10.10.10.1 (Distance = 1) WAN2 gateway: 11.11.11.1 (Distance = 2) I'm not using any policy routing, juts normal default routing. All lan traffic to intern...

nerdtron

Hotspot does not redirect SSL 443 sites , unless you enable HTTPS redirection and run the hotspot on 443 on the Mikrotik. You will then substitute the lack of redirects for an HTTPS certification error. That is sad to hear. No known workaround yet without using https on hotspot? I think is better n...

nerdtron

Hi all, I have activate hotspot for wifi user on my RB951. Problem is when users type google.com, they are redirected to https://google.com and an SSL error appears. "Unable to make a secure connection to the server." This only happens when users try to access a https site. Normal http sit...

nerdtron

No... Slave interfaces shouldn't have IP addresses, any DHCP/hotspot servers, etc. You should set them on the bridge interface (master). Can you elaborate more why you can't or you shouldn't do this? I have 2 SSID, the first one is the primary wireless interface and the second is a virtual IP. The ...

nerdtron

Ah it works now! I must have clicked it sometime when I was testing.
Thanks!

nerdtron

Thanks for the tip on https:// Is there a way to redirect https sites too? Anyway, I tried to access a normal http site and still no good. Only a blank page. On the status bar of the browser it says Looking up local... Then changes to Waiting for www.local.com... It just loops between the two. Any i...

nerdtron

Hi all, I was following this tutorial to have an external login page for mikrotik hotspot. http://wiki.mikrotik.com/wiki/HotSpot_external_login_page So far it is working good, when a users wants to browse the web, they are redirected to the login page which is located on a another server. But this o...

nerdtron

You can add the URL or IP address to the walled garden of your hotspot. This is more like a whitelist, which allows the users to access certain websites without the need to login. Then you can add a link on the hotspot page to that page. If users want to browse other websites that is not defined on ...

nerdtron

If each client is connected on their own ethernet port on the mikrotik router, you can try limit upload/download limit per port.

nerdtron

I used this tutorial. Wokrs great. http://wiki.mikrotik.com/wiki/HotSpot_e ... login_page

nerdtron

How did you *merge* the two wan? Like the above poster said, you can't connect to a server using two different ip (because you have 2 wan). Try torrentiing and you can see improved results. On normal browsing and file downloads, you can only use one connection at a time. Load balancing only works by...

nerdtron

Try bridging the wlan and the lan ports. I remember when I first tried hotspot on the default setting of the rb951ui, my lan computers were redirected to the login page of the hotspot.

nerdtron

I use a freeRadius server with mikrotik clients. When I receive the errror "unknown address" usually is that the address of the mikrotik client is not allowed (or defined) on the server for authentication. What IP are the mikrotik client uses to communicate to the Radius server? I think yo...

nerdtron

Onn the openVPN server config file, you should have a line there for disabling TLS, Also, don't use compression and use TCP for connection.

nerdtron

How do you configure your VPN server? you should "push routes" from server to clients so that even without the default gateway option, your client will know the routes from the VPN server.

nerdtron

If it is /30, then it is just a point-to-point connection, one is your ISP and one is your WAN IP.
Or do you have more IP blocks?

nerdtron

I use freeradius as well with mysql database. I use DaloRadius web config to define users. Using this web GUI, I can define a session timeout for each user.

nerdtron

The link above will be very helpful. I made some adjustments when I followed it.
Have you looked at my thread? http://forum.mikrotik.com/viewtopic.php?f=2&t=80027

nerdtron

You can't use a vpn channel on constantly changing/switching connection unless you have a way to have the same source address when you switch connection. So either you setup a failover setup or if you have two links, you can have one vpn tunnel each.

nerdtron

If it is Ethernet port limiting, you can create a simple queue in winbox to limit the speed per port.
http://www.youtube.com/watch?v=wBVqzYYnAJ8

nerdtron

What is the mail.log of the mail server when mikrotik tries to send email?

nerdtron

Does your wifi has the same IP block as your LAN? Make specific NAT rules, let's say your lan start at 192.168.1.2-50, then wifi IPs are 192.168.51-254, then created a NAT rule that will only NAT LAN IPs. Define the scr-address-list in address lists. Or if your testing wifi from a single IP (say you...

nerdtron

Many ways, if the device is just connected via wifi, just unplug the internet connection and the see what happens. The device is still connected to the wifi but no internet connection. Then plug the internet connection again. Another option would be to disable/enable the nat rules. Open up winbox an...

nerdtron

Get a battery pack that has the same rating as the power adapter of mikrotik. Then either buy a cable or solder you own so that the power cable is the same that can be plug on the mikrotik.

nerdtron

I think I solved it (I still need to confirm if packets are marked correctly), in case somebody will encounter same problem.

Add hotspot=auth on mangle rule for wifi and then add a nat line.

/ip firewall nat add chain=pre-hotspot dst-address-type=!local hotspot=auth

nerdtron

Hi all, I have the following config: The setup is lan network ports (192.168.14.0/24) will be routed to wan1 and wifi users (192.168.15.0/24) will be routed on wan2. It seems to be working as expected. Problem: When I activate the hotspot for wifi users, users are not redirected to the login page. T...

nerdtron

Hi all, I have the following config: The setup is lan network ports (192.168.14.0/24) will be routed to wan1 and wifi users (192.168.15.0/24) will be routed on wan2. It seems to be working as expected. Problem: When I activate the hotspot for wifi users, users are not redirected to the login page. T...

nerdtron

OK, I think I made some progress, instead of just src-address in the mangle rules, I made it src-address-list and then added firewall address-list. /ip firewall address-list add address=192.168.14.0/24 list=lan-users add address=192.168.15.0/24 list=wifi-users /ip firewall mangle add action=mark-rou...

nerdtron

Rudios, I am aware of that, thanks for the reminder. Here is my export: #lan1 is 192.168.14.0/24 network #wifi network is 192.168.15.0/24 #wan1 gateway is 192.168.20.1 #wan2 gateway is 192.168.46.1 Basically I want all wifi to pass on wan2, and I want all lan1 to pass on wan1 /interface ethernet set...

nerdtron

You mean the login.html from the mikrotik hotspot page?
Open Winbox, then click Files. You'll see a folder there named hotspot which contain all template files. Just drag the whole hotspot folder to your dekstop and everything will be copied.

nerdtron

That is exactly what I followed before posting here. Almost the same setup, only difference on mine is lan1 is from the lan ports (3-5 interface) and lan2 is the wlan1 interface.

But fail, is that tutorial even working or I need to add more config that is not mentioned on the tutorial??

nerdtron

So I have two seperate LAN, 192.168.1.0/24 (lan1) and 192.168.2.0/24 (lan2). I also have two gateway (internet) on port1 and port2 of the RB951.
I want to make all lan1 have a gateway to port1 and all lan2 have a gateway to port2?
How can I approach this?

nerdtron

Download Winbox. http://download2.mikrotik.com/winbox.exe You can connect a PC directly to any LAN port, and then open winbox. Connect using the MAC Address of that port and the System>Reset configuration. This will erase all config and only the factory defaults will remain. Using the physical reset...

nerdtron

What is your /ip firewall nat export?

nerdtron

Add a comment to the wlan1 as "WIFI" ##netwatch script 1,check if internet on port 1 is down ## This will ping 8.8.8.8 on the internet, if it doesn't respond in 15 consecutive tries and if wifi is up, wlan1 interface will be disabled. :local i 0; {:do {:set i ($i + 1)} while (($i < 15) &am...

nerdtron

Great. Thanks a lot for this. I'll update if I have problems.

EDIT: Seems to be working!

I'll need to take to the programmers on how to customize this further.

nerdtron

Has anyone tried this in the wiki? http://wiki.mikrotik.com/wiki/Manual:Customizing_Hotspot#Misc Scroll a bit down to see the "Making HotSpot to authenticate on a remote server" part. Basically, the concept is that the login page will be hosted on an external server. Then once you click su...

nerdtron

Thanks. Yes I'm aware of these. But as far as I understood, you define the profile that the router assigns on a user is defined on the router. Is it possible to define the "session-timeout" of a user from the radius server? I mean, the radius server will push settings to the mikrotik route...

nerdtron

Hi all, I was setting up a Radius server today for use by the hotspot in mikrotik RB951Ui. It seems to be working as I was able to authenticate a few test users on the landing page of mikrotik hotspot. My questions is, after I authenticate the user, what is the default time before they need to authe...

nerdtron

Hi all, I followed this guide http://wiki.mikrotik.com/wiki/Improved_Netwatch_II Script 1 pings a remote host using WAN1 and then if it fails, it set the default route to 3 which makes the WAN2 the default route. It works fine. However once the connection is back again on WAN1, it no longer detects ...

nerdtron

Thanks for your replies. I read the config again. Seems like the default was to use UDP and Mikrotik doesn't support it. Changed the server config to TCp and its working now.

Now I can begin writing scripts for failover.

nerdtron

I followed them all. We even have the same tutorial for the openvpn server. I'm sure it is working as I can connect a Linux computer or another router as a client to the vpn server. The server is working fine. How ever when I try to connect the mikrotik RB951Ui-2HnD, I can't connect to the server. T...

nerdtron

Great, thanks for your reply. I am now using winbox, but I still get disconnected when I disable port 2? I think it's because the master-local port and the other port are dependent on it? Can you explain the structure of these interfaces and how do I make them independent of each other? Thank you fo...

nerdtron

Hi all, I have a Mikrotik RB951Ui with a total 5 LAN ports in which port 1 is the WAN port. It came with the default configuration. But I want to have dual wan setup so I want port 2 to act as WAN2 port. I can't seem to figure out how to start the configuration. I can only access the device using th...

nerdtron

Hi all, We bought this router RB951Ui-2HnD routerboard. It's small and has 5 ports wherein port 1 is the default WAN port. I new to this router OS and the web GUI is quite overwhelming. However, here is were i get stuck. I want to make port 1 and port 2 as WAN port, and every time I change something...

nerdtron

Hi all, We bought this router RB951Ui-2HnD routerboard. It's small and has 5 ports wherein port 1 is the default WAN port. I new to this router OS and the web GUI is quite overwhelming. However, here is were i get stuck. I want to make port 1 and port 2 as WAN port, and every time I change something...

Search found 123 matches