I've tested mANT LTE 5o... that is disappointed me...
On our frequency LTE 800 that have VSWR around 1.27.
Maximum VSWR 1.06 i detected on international LTE bands "LTE 900"
Zorro - no need to complicate! If my network does not require these technologies, I will not introduce them. Mikrotik it is best choice for my net. It is only 500 dollars per CCR1009 device(i pay two times more for my low cost 10G D-Link switch) If you need these technologies, you can use any equipm...
For my net do not needed IS-IS, VPLS, MPLS, HWMP, OSLR... and other strange words :lol: :lol: I use it just a simple internet gateway with PCQ, 2ch. load balance+failover, IPv6 and OpenVPN gateway, VLAN routing with firewall. Just at all. And Mikrotik doing this very-very good! Mikrotik solution mor...
Dear Mikrotik, you are CRAZY !!!! REALY !!! CCR it is a monster! On product page you dont have info about PPS. I test it. Your CCR router with only 9 (NINE!) cores transmit 1 000 000 PPS small packets over vlans with FastTrack, and use only 10% of CPU. And 0.56MPPS without FastTrack. This is very-ve...
When i install CRS226 in my net, i do smoke mikrotik manual at 2 days! After HP ProCurve and Linksys switch, Mikrotik config i seen too complicated. In classic routing and firewall i'm not need any manual on mikrotik, because i Linux sysadmin i understand all config clearly, but not in switch featur...
Mikrotik docs on CRS series is a terable :lol: Maybe my config help to you little. /interface ethernet switch set drop-if-invalid-or-src-port-not-member-of-vlan-on-ports="SFP-10G,ether1-QRT2,ether2,ether3,ether4,ether5,ether6-34410A,ether7-MyPC,ether8-MyPC,ether9,ether10-Akip,ether11,ether12,et...
Hi Hrobocop, i recomend in your auto-update script add delay between load new firmware and reboot. Like this: :log info ("Downloading new RouterOS on router $[/system identity get name] from $[/system package update get installed-version] to $[/system package update get latest-version] (channel...
"action-on-static-station-move=drop drop-dynamic-mac-move=yes" - works without any log entry. Ports steel active, no traffic on loop ports, and all works fine. But "chechito" make rights thing, unicast-fdb-timeout must be decrease(i set 120s), because if you reconnect user from o...
Loop protect it is a basic function of EVERY L2 managed switch as i see latter... I've seen a lot managed switch for my 15 years career. But i never seen that epic-fail until now! Hm... I see, CRS is a trash! It is horrible ! My old HP 1810G-24 do all what i want.... i think about return it in rack....
How i can enable Loop protection on CRS226 ?
As example, if i install pach-cord between ether3 and ether4, switch has died
I need connect new user via two 1G channels (with many little kids and complicated hardware config), and i see the loop as the big danger for my network as not far future.
I set on all CRS226 ports learning override to 10,50,100 MACs. Also i created two trunk ether7+ether8 and ether23+ether24 But if i run flood attack to CRS MAC table via trunk this limits not works :( trunk-macof.png As you can see, allmost all of 16384 MAC entry in table store on port MySRV- trunk ....
100Mbit without tunnel. However I plan to use VPN, probably PPTP CRS112 could be used as a router and switch simultaneously? I recomend RB850Gx2 for this. I think RB750Gr2 also be fine. CRS is too slow for that. My CRS utilize 20-35% CPU right now, for nothing! No internet, no tunnels, no data tran...
I talk with support now. Maybe it help you Hello dear Mikrotik! I want buy CRS226-24G-2S+RM, but i do not understand, these switch support Link aggregation 802.3ad with VLAN without CPU? It is very important for me. Because i planned replace my old HP 1810-24G with CRS226-24G-2S+RM and i need config...
UNIX based sysadmins like MikrotiK routers, but often home provider not give Static IP. Today i have fix it mistake, but DynDNS not pay free more. ;( I as many sysadmins have access to LINUX based web-server. Then i write mikrotik based "HTTP GET" IP pushing script. It's sent to web-server...