MikroTik

fengyuclub

I didn't read your update carefully. After following step 2a), it worked normally. Thank you.

fengyuclub

What is your routerOS version and script version? Post output of: /ip/kid-control/print It should show the day of week its enabled like this: Columns: NAME, SUN, MON, TUE, WED, THU, FRI, SAT # NAME SUN MON TUE WED THU FRI SAT 0 Monitor 0s-1d 0s-1d 0s-1d 0s-1d 0s-1d 0s-1d 0s-1d If that is ok, you ha...

fengyuclub

You have followed the 2e settings about kid control?

This is for sure. I submitted the bug after confirming it.

fengyuclub

Found a bug, there is no data in traffic

2024-03-29_14-38-06.png

fengyuclub

Everything is OK. Thank you.

fengyuclub

`index` sourcetype=mikrotik module=script script=health host=10.0.0.1 name=temperature | where value>50 Error message: "Error in 'SearchParser': The search specifies a macro 'index' that cannot be found. Reasons include: the macro name is misspelled, you do not have "read" permission...

fengyuclub

2024-03-18_17-26-08.png

fengyuclub

I upgraded an rb750Gr3, upgraded v5.3 to v5.6, and then saw the scene as shown below. I understand that the serial number is not displayed, but for what purpose is the other attributes not displayed? At least the "identity" is displayed. , or where I made it rough, please tell me. 2024-03-...

fengyuclub

Updated "MikroTik Device Traffic" to give correct graphs if router is rebooted or counter is reset. Get your update from git. After the update, the above problem has been solved,but "script error: error - contact MikroTik support and send a supout file (10)" This error message s...

fengyuclub

fengyuclub Hi problem with "script error: error - contact MikroTik support and send a supout file (10)" in "#Get detailed command history RouterOS" is probalby related to number of enrities in /system history - if there are too many entries, an error message appears (even execut...

fengyuclub

One of my ccr1016-12G doesn’t record data to splunk anymore. I can see the error message in the mikrotik log, as shown in the figure below, every time it is 998. It’s very strange. I try to stop and delete the corresponding one according to the error log field. "# Count IP in address-lists"...

fengyuclub

When I replaced this router with a spare router (also a ccr1016-12G), the replaced ccr1016 with a problematic authorization went back to normal after re-powering on and logging in, and there was no authorization prompt. Not sure what the problem is. Luckily I have a spare router, otherwise it would ...

fengyuclub

The business cannot be stopped, and there is no choice but to replace the backup route.

fengyuclub

no response received

fengyuclub

device serial number and supout.rif file has been sent to support@mikrotik.com，hope it can be resolved soon。

fengyuclub

What did you do, before this happened?

Email support@mikrotik.com with device serial number and supout.rif file

Forum can't help with this, you need support department

I have already submitted a request, do I still need to write to support@mikrotik.com?

fengyuclub

Today my CCR1016-12G received a warning that the authorization is invalid. Follow the prompts to update the License key, and it shows “done”, but after logging in again, the same prompt remains, indicating that the router will stop operating within 24 hours. What should I do? I also submitted a supp...

fengyuclub

According to your suggestion, I changed it slightly and it works normally.

fengyuclub

My mikrotik is ccr1016, and the /system/health/print information is as follows: system health/pr Columns: NAME, VALUE, TYPE # NAME VALUE TYPE 0 cpu-temperature 50 C 1 fan1-speed 5730 RPM 2 fan2-speed 0 RPM 3 board-temperature1 28C 4 psu1-state ok 5 psu2-state fail How should I write the alarm script...

fengyuclub

thank you for your reply. I just applied for the 10G enterprise license according to your post. I read the official splunk manual about webhook, but I didn't find a solution. I'm looking for other ways. In fact, this notification is to solve the high temperature reminder caused by the power outage o...

fengyuclub

I set it up step by step according to the steps in your post, and it started working, and the data was indexed, which is great. There is another problem. I have been using a high temperature warning script, but now it seems that it cannot be used after v7. After reading many posts in the forum, I ca...

fengyuclub

You can use chown -R on the folder to sett correct user/group.
Installing it using git will be som manual work.
You can use git pull and point it directly to your folder, but that will make a risk of overwriting stuff you do manually.

please help me

fengyuclub

@Jotne

fengyuclub

I recently re-deployed a splunk9.0.5 machine on the intranet, and then forwarded all the previous logs to this splunk. The data can be indexed, but the dashboard in the application has no data, and even basic dhcp requests can be seen No, why is this? Is the splunk version too new?

fengyuclub

First of all, I am not very familiar with mikrotik routing, but I basically understand your needs. Although wireguard is currently the best performing vpn, it still affects performance. The bypass mode is recommended for devices such as Android TV, no need to set. There are many xray clients for oth...

fengyuclub

I think the VPN protocol is different. Commonly used VPN protocols such as ipsec are easily detected by gfw and block traffic. I understand. I guess I live in the same country as you. If you want to avoid censorship, you can consider deploying your own vps node with a more advanced xray protocol. I...

fengyuclub

What is your purpose? I am somewhat dizzy after looking at your topology. If openwrt is for client bypass routing service, you can use ip dhcp-server option code 3 & 6 to distribute gateway and dns. If you are accessing internal lan-side services externally, you already have esxi, so it is more ...

fengyuclub

The problem is solved, just add a routing mark on the rb750 route chain=prerouting action=mark-routing new-routing-mark=main passthrough=no src-address-list=local-LAN in-interface=bridge2-LAN But in this case, you can see that the client cannot aggregate the sum of the bandwidth of the 3 ISPs, and c...

fengyuclub

yup, need to see complete config on both routers
/export file=anynameyouwish ( minus router serial number and any public WANIP info )

export file

fengyuclub

Can you give me some hints combined with my topology, although I have some basics of mikritok router settings, but I am not very professional.

fengyuclub

Checked the official wiki document, the configuration is successful, the mikrotik devices at both ends are v7.7, just a few days ago, the mikrotik device at one end (rb750gr3) was upgraded to the latest version of v7.8, and then it didn’t work, and the other end Also upgraded to v7.8, still can't ac...

fengyuclub

Thank you for discovering the problem. After I enabled system/package/wireless, the problem was solved. Since I use the router as a hardrouter, there is a separate unifi control to take over the ap device, so the wireless module is naturally disabled. It should be the problem. As for the dhcp proble...

fengyuclub

Has been sent

fengyuclub

Has been sent

fengyuclub

The ssh access permission has been sent to your email.

fengyuclub

Tried both true and false, there is no prompt or output in the log

fengyuclub

Sorry I didn't read your post carefully
script=resource free_memory=1575 MB total_memory=1952 MB free_hdd_space=428 MB total_hdd_space=512 MB cpu_load=12 uptime=4w3d04:50:39 write-sect-total=

fengyuclub

Tested the script on several mikrotik, but again there is no output, as shown in this picture. 'print' will output information

2023-01-12_09-21-49.png

fengyuclub

index=* host=10.0.0.1 | fillnull value="-" | stats count by module script | sort -count script 5.1 dhcp - 186239 dns - 1017 script - 12 system - 4 e-mail - 1 script4.9 dhcp - 517849 script kids 115519 script neighbor 6456 script upnp 4935 script if_traffic 4785 script address_lists 4060 s...

fengyuclub

Using the 5.1 script, you can’t see any action in the log after manually running it, which can be understood as not running. After manually running the 4.9 script, you can see the output immediately. 5.1 Is this paragraph in the script the cause “# Get RouterOS main version (used to run different sc...

fengyuclub

The same two ccr1016s have the same firmware version 6.48.6, but one does not work after upgrading the 5.1 script. There is also a CCR1009-8G-1S that has the same problem. I checked the update log and other files, but I can’t see where the problem is. Can you tell me what the possible problem is?Cur...

fengyuclub

Although I updated the script and application today, I have always felt that the visualization of interface traffic is not very good. Where should I adjust it?

2022-09-13_15-52-13.png

fengyuclub

Checked the log, this problem still exists, how to solve it, but it seems to have little effect.

2021-07-22_09-11-32.png

fengyuclub

Snipaste_2020-03-30_15-12-42.jpg

Why the font of my winbox is different from yours, how can I use arial font, only the menu bar is arial font.

fengyuclub

Somehow just fine, I carefully compared the configuration before and after, only / ip route rule add action = lookup-only-in-table dst-address = 10.0.0.0 / 23 table = main is added later, it may be because the router has not restarted. I set it to restart every Sunday, does this rule need to restart...

fengyuclub

I added 4 mangles to the top as you said. You can see that the fourth one has no data packets passing through. What should I do?

add chain=postrouting src-address=1.1.1.1 protocol=tcp src-port=8180 action=log log-prefix=step4

1.png

fengyuclub

Removing sensitive stuff is ok, but it must not break ability to understand the config. If you ask about port 8888, I need to see dstnat rule for port 8888. Currently it's not there. If it contains a public address you want to hide, it's no problem, just replace it with your fake 2.2.2.2. I can loo...

fengyuclub

myconfig

fengyuclub

I gag when I see the use of VLAN1. I would change that to vlan100 or any other number but I doubt it has any thing to do with any of the issues at play. After reading your article about vlan and que, I was very inspired. Vlan1 is actually base vlan, or the default vlan and management vlan. Maybe my...

fengyuclub

Try again and be more accurate. There's no dstnat for port 8888 like you had in original post. Only dstnat going to 10.0.0.2 is port 1514, which can't work from LAN because it has in-interface=WAN-ether2. But that wouldn't work not only from vlans, but neither from main 10.0.0.0/23. And I'm not sur...

fengyuclub

re-upload

fengyuclub

It's not hairpin NAT problem. Only devices in same subnet as server need hairpin NAT. In your case it's only vlan1. Both vlan10 and vlan11 have diffent subnet, so no hairpin NAT is needed there. It's probably your routing. If you mark routing from vlan10 and vlan11 in order to use WAN 2.2.2.2, it's...

fengyuclub

Hello everyone, I recently encountered a problem, I have read a lot of posts, it should be the problem of hairpin nat, but my situation may be a bit special, I hope to get answers My network configuration is roughly as shown in the figure. There are 2 Internet access lines, one is a static IP: 1.1.1...

fengyuclub

Recently, one of my ccr is a bit problematic. I can only recover from the time when the device is powered off and restarted. The top of the log in winbox can see red like "system, error System rebooted because of kernel failure" or "Out of memory condition was detected", but I ca...

fengyuclub

I have Splunk Enterprise license, gmail alert can't be real-time, mobile mail client can't update mail in real time, there is a delay of about 10 minutes, so I choose wechat alert.I received some wechat alert, but some of them use the search to save as an alert, I can't receive a wechat alert, I don...

fengyuclub

Splunk is really powerful, I see splunk have a lot of apps to install, in our China use wechat (similar to facebook, telegram) this social software, I saw this social software related app, WeChat Alert App for Splunk, I installed this App, sending test messages from wechat is successful, but I don't...

fengyuclub

Host=x.x.x.x Although this option is available, some devices have an internet connection that is a dynamic ip obtained by adsl dialing. So before the log warning, add an identity=xxxxx to distinguish the mikrotik device. After testing, it is feasible and runs very well.

fengyuclub

Understand, add host=x.x.x.x in front of the search statement you gave to open my ccr and rb.

fengyuclub

Jotne，Great, I did it according to your script, and the beautiful chart shows normal. I tried to add scripts to my multiple ccr and routerboards, so my interface has a lot of duplicate names, such as bonding1 and bridge1, how can I distinguish between them, or change the name for each interface. 4.p...

fengyuclub

Tested on other ccr1016 your script is successful, it should be the problem of the interface name, but it is important to draw the splunk graphics, I hope you can add to the new version.

3.png

fengyuclub

Your script, the regular expression method, no success without any output, it doesn't matter, my code is as follows I want to know how to search for rich charts, and there are 14.8Mbps and 14833 display problems. This is not important. The important thing is how splunk draws charts. mycode { :local ...

fengyuclub

{ :local iname; :local monitor; :local speedRX; :local speedTX; :local mbpsRX; :local mbpsTX; :foreach interface in=[/interface find] do={ :delay 100ms; :set $iname [/interface get $interface name]; :set $monitor [/interface monitor-traffic $iname as-value once]; :set $speedRX ($monitor->"rx-b...

fengyuclub

/interface monitor-traffic LAN once do={:put $"rx-bits-per-second" }

How to record this value to the log and let it display like 14.5Mbps, retaining a decimal point. Trying to find the entire forum, many will not work.

fengyuclub

What command do you use on the router to see this data?

interface monitor-traffic ether1

Search forums see scripts with such calls

  "/interface monitor-traffic ether1 once do={
:put ($"tx-bits-per-second"/1000 /1000 )
}"

fengyuclub

How can I write the interface tx-bits-per-second parameter to the log and then plot it in splunk.

fengyuclub

Splunk is too powerful. If I have multiple ccr1016, how can I transfer data to the splunk server, how do I distinguish syslogs from different mikrotik routers?

fengyuclub

The data is coming, some of the tables are already filled, some still have no data, such as dns, it doesn't matter, I want to know how to monitor the flow table of an interface (wan), just like mirkrotik's built-in mrtg chart, every 5 minutes, 30 minutes and so on. . . As shown

1.png

fengyuclub

It’s true that I set it wrong, Mikrotik changed to MikroTik, and it should be fine, then I will report it.

fengyuclub

There is no local listening udp514, now there is data in, but click on the meter in the Mikrotik2.7 dashboard, most of them do not have any charts, how to add or customize the dashboard you need here, for example, I want The wan's real-time or past and downstream traffic in a certain period of time,...

fengyuclub

After starting Splunk, go to Search & Reporting menu. Add following search: sourcetype=mikrotik and set last 24 hour. Do you then see any data? If not try to just use a * (star) and last 24 hour. If you do not see any data, make sure Router is sending data to correct IP/Port. Splunk is listenin...

fengyuclub

Reinstalled splunk on ubuntu18.04, is a virtual machine under esxi, the deployment is very simple and normal, according to the steps of the top post, but the splunk dashboard can not see the task data incoming. Very strange, what else do I need to pay attention to? Please forgive my English using Go...

fengyuclub

I have been paying attention to this post, very powerful chart, but the cumbersome construction and the lack of relevant knowledge have been unsuccessful. I can only temporarily use the mrtg icon inside routeros to temporarily cope with it. I hope the poster can write the deployment manual from the ...

fengyuclub

"after few times throughput goes down and does not exceed 1-2MB/sec (everything else still works except bandwidth)."

This phenomenon is exactly the same as my failure.

fengyuclub

My question is about the link aggregation problem, the same ccr1016, one can fail another ccr1016bonding, just the switch is different, after searching the forum, I found this post and I have the same problem, please can get the answer. Is the switch required to support the lacp protocol to do the b...

fengyuclub

Good idea moving the cpu reading to the top. I have updated fist post view new version. PS mine du not give much difference in CPU when script is running. Maybe you device is some under-powered or you have som wrong in your configuration (fasttrack or hw acceleration missing) I see that MB is wrong...

fengyuclub

http://blogs.catapultsystems.com/mdowst/archive/2018/06/18/install-elastiflow-on-ubuntu-18-04-part-1/ According to the 4 steps of the above article, the installation is complete, you can access, but how to inject the traffic data of mikrotik router into elastiflow? The xxxx.json dashboard file impor...

fengyuclub

i hope so

fengyuclub

It's great to support Pushbullet.

fengyuclub

It's great to support Pushbullet.

fengyuclub

viewtopic.php?f=9&t=111073

fengyuclub

tools/netwach host=74.125.135.138 up= /tool e-mail send to="youremail@gmail.com" subject="Internet Connection Status" body=([/system identity get name] . " back UP in " . [/system clock get time] . " on date " . [/system clock get date]) down= /tool e-mail se...

fengyuclub

I am also the same problem, hope mikrotik can see and solve this problem.

fengyuclub

The problem is found, the problem is winbox3.8, winbox3.7 normal.

fengyuclub

New version 6.37.3, why specify the Dst.address, can not specify dst-port, the option is gray, not available, how do I do port mapping operation? Upgrade 6.38 or so can not operate.

1.png

fengyuclub

helpme

fengyuclub

please help me! http://forum.mikrotik.com/viewtopic.php?f=9&t=116156

fengyuclub

fengyuclub

Read some topic, the perfect solution to my problem.http://forum.mikrotik.com/viewtopic.php?f=9&t=111627 :local oldip [/ip firewall address-list get [find list="xxxxxip"] address]; :local newip [/ip address get [find interface="adsl"] address]; :local newip [:pick $newip 0 [:...

fengyuclub

How can we address-list in a dynamic ip address Export to file，My intention is trying to host a daily list of online comparison.

chain=prerouting action=add-src-to-address-list src-address-list=ether1-lan address-list=Online address-list-timeout=5m log=no log-prefix=""

fengyuclub

I suggest you try, two ubnt NanoStation Loco M2 to each other on the radio, if the fear of 2.4g interference, then use loco m5, should be able to solve your problem.

fengyuclub

I used the phrase "/ ip firewall nat remove [find comment ~" ^ upnp *. "];" After the wan ip change can delete the old upnp mapping.

fengyuclub

I mean, if there are multiple network clients have upnp demand, dst.port the changes, restart the port after the client request (dst.port) will change, how to achieve it?

fengyuclub

What's the 450G ROS version? firmware version? That post is almost 10 years old... in addition, there have been lots of uPNP fixes. I carefully observed the ip address range my adsl out (isp) obtained, xx.xx.xx.2 ~ xx.xx.xx.12, how to make adsl out to get the desired ip address, otherwise, have bee...

fengyuclub

Try this script. schedule it to run every 5mins. It will check if the ppoe has a new IP and if it does, it will remove the entries for upnp. :global currentIP; :local newIP [/ip address get [find interface="ppoe1"] address]; :if ($newIP != $currentIP) do={ /ip firewall nat remove [find co...

fengyuclub

I find the solution myself!
Just create a rule manually, all parameter as the same as the previous UPNP rule, except fill the "dst. address" as "!192.168.0.0/16", instead of the WAN address, it works!

This solution is limited to the internal network has only one client device

fengyuclub

rb450g v6.36.2 fireware is 3.24 . The latest version

fengyuclub

http://forum.mikrotik.com/viewtopic.php ... pnp#p59994This topic is the same problem and I hope Solutions

fengyuclub

Why not simply use ip > cloud? If you have a web or other kind of server behind the mikrotik, you want to be available from outside, just create a CNAME (on your domain DNS) referring to the routerboard xxxxxxxxxx.sn.mynetname.net record. Thank you pukkita, maybe I did not explain what I mean, I am...

fengyuclub

I press this script（ http://forum.mikrotik.com/viewtopic.php?f=9&t=111073#p552202 ）, if wan ip change, send e-mail notification, has been working satisfactorily. ip-per-acquisition are xx.xx.xx.2 ~ xx.xx.xx.12, how to make it in a fixed ip, such as xx.xx.xx.10, if not xx.xx.xx.10 , repeatedly di...

fengyuclub

Hi, I run a scheduled script, below, at regular intervals. Make sure your email settings on the router are working first and change the interface name as required. The script store the address in a firewall address-list so it can compare it if it changes. I use the same address-list for my hairpin ...

fengyuclub

i am a chinese user,my english is poor,please help me . thanks.

fengyuclub

Hi guys , I need a script code ,when my isp(pppoe) ip address changed ,send this changed ip to mymail,if ip isn't changed no send. How to do???

fengyuclub

Nice! Use your script successfully sent mail

fengyuclub

2 wireless Internet access, the same isp, how bandwidth superposition, 2m + 2m = 4m
Another problem, how to use the new version “ip cloud”,what effect can be achieved？
please help

Search found 104 matches