’m doing the load test on the CCR1036, we found that the latest version 6.37.1 cannot obtain the > 1million PPS on the 1G link, while the older version 6.7 can. Can you look into it accordingly? Here is the test case CCR1 Traffic Generator ether2 => CCR2 ether2 => CCR1 ether3 CCR1 Traffic Generator ...

You might look at your profile, if using compression, encryption. change it to default. also look at ur firewall setting. make sure allow gre and TCP 1723

Dear All I have some problem when using PPTP Server + UserMan together. I'm doing a lab using CHR 6.36.2 and RB951 6.36.2. I'm able to authenticate via usermanager and account via usermanager. However, after 3 minutes, all the client stop receiving packet. I have check the quota limit had not been r...

I have similar issue previously with the bad power supply on CCR1036. The voltage drop below 14volt when the CPU load increase. And subsequently it will reboot automatically.

Take a look of ur power voltage when it CPU load surge.

Dear All I have a Layer 2 connection between office network and remote site using EoIP tunnel. which is a great! but i have observe a problem on the STP connection. The office network are using good old Cisco 2950 and 2960G switch, having the PVST configured for loop free connection. while the mikro...

I think i had figured out what was going on. 1 of my customer who having a messy network bridging different vLAN with the cable. There might be a loop in their network and having the STP sending out to the router. I just don't understand why the STP will affect the router. as 1) i'm not using any br...

That was me...hehe

I don't think there are infrastructure change 1) Friday night, everyone went for Happy Hour :-) 2) The switch port have a broadcast control, if there is an loop the spanning tree will kicks in, and if the spanning tree cannot detect the loop, the broadcast control will errdisable the switch port 3) ...

Thr 3rd CCR, Initially, on 3.11+6.7 and died during configuration. Upgrade to 3.22+6.28 still not working. Share the same behavior as the rest of CCR.

Was the 3rd router also upgraded to 6.28 and 3.22 ?

Frankly speaking, testing I had done. But you will not do load test at such condition as a end user. This is the job for vendor to test in different senerio. Sorry to hear about all your troubles....as others have said, it is usually a best practice to test code for critical environments before depl...

Yes, fast path is enabled, but you see there are no packet going through the fastpath channel because you have the vlan enabled. if you turn off the vLAN, you will able to see the fastpath counter increasing. What's new in 6.30rc17 (2015-Jun-11 10:24): ... *) fasttrack - added dummy firewall rule in...

I was trying to use fastpath but not fast tract. agreed with you fast tract is new, don't want to take the risk. Fastpath was there since early release of 6.xx. I suspect the incident is related to the BGP, where when i reboot the CCR and hitting the issue. the old routing table still there, maybe b...

Last Friday night is a disaster.. and i would like to share if anyone can give me some clue I am running 2 x CCR1036 as the core router as the ISP service. Running for more than 2 years without problem on version 6.7. Since it was being a while, and i would like to have a fastpath support for my nat...

Good to hear that.. as i'm trying on the 6.29.1 for the fast track and fast path. both are not working if the in/out interface are on vlan.. Looking forward for 6.30 Hello All Does anyone know if fastpath is supported on VLAN interface? It isn't currently supported as of the latest official release ...

The log file was too big aa require to enable the debug mode. At anyway, I had managed the issue by not using the aggregate function on the bad router, and redistribute the aggregated prefix from other good router. Need to schedule the reboot sometime, as if the goos router become bad, I will lost a...

Hello All

Does anyone know if fastpath is supported on VLAN interface?

Thanks

Benny

Hi I just experienced a problem on advertised prefix flapping in my bgp connection to upstream. I have a pair of ccr1036, each of them running 3 full route, and exchange the route using 2 x delicates port and 2 bgp sessions to exchange route between two. And I had breakdown my /22 subnet into multip...

When will v7 release.. waited for long time..

Hello I'm using the CCR1036 for a year, on 6.7 everything is very good so far. I had used BGP, VRRP, VLAN, Traffic Flow, IPv4 & IPv6. The only compliant that i have is the BGP multicore load balancing, as we are having around 40 peers, sometime the BGP instance dies and mess-up the table. Anytim...

If you are already running a RouterOS 6 install, Simply click “Check for updates” in QuickSet, Webfig or Winbox packages menu. What's new in 6.11 (2014-Mar-20 09:16): *) ipsec - fix aes-cbc hardware acceleration on CCR with key sizes 192 and 256; *) wireless - add auto frequency feature; *) ovpn - ...

Hello, We are seeing something strange.. We tag certain prefixes announced to us with bgp communities, eg. 11280:115 etc. (ROS ver 5.21 as well as 5.26) We use these communities in our bgp filters for prefix announcements. e.g. chain=out-filter match-chain=XYZ invert-match=no action=accept set-bgp-...

+2. I have a case just happen today, suspend because of the upstream have a big BGP update at 2014-01-17 10:50 GMT. ~ 10k - 15k route update received from my Cisco router, and pass along to my new CCR-1036. at the sametime, some of my subnet lost connection, and suspect because losing part of the r...

Currently CCR1036 and CCR1016, both ROS v.6.9, so far so good. Regards, What are the features that you are using now? I have a CCR1036 using for BGP( 3 x full route, around 20 neighbours) , IP Filter, vLAN, VRRP, Netflow, IPv6, SNMP. sometime it just hang for couple seconds and back to normal. Want...

+2. I have a case just happen today, suspend because of the upstream have a big BGP update at 2014-01-17 10:50 GMT. ~ 10k - 15k route update received from my Cisco router, and pass along to my new CCR-1036. at the sametime, some of my subnet lost connection, and suspect because losing part of the ro...

Same here, i'm using the CCR-1036 with the latest firmware and ROS 6.7. when i type /ip route print detail where 1.1.1.1 in dst-address, it never show up

i'm have multiple feed of BGP connection, with couple of them are FULL table.