understood regarding the limitations of the device. To be fair it was an old unit that has been sat in my toolbox unused for a number of years, i guess it is time to retire it

Hi thank you for your reply - here is the terminal output: [admin@MikroTik] > interface ethernet print detail Flags: X - disabled, R - running, S - slave 0 R name="ether1" default-name="ether1" mtu=1500 l2mtu=1598 mac-address=D4:CA:6D:EB:CC:4C orig-mac-address=D4:CA:6D:EB:CC:4C a...

all my ports are the same as the screenshot, and i did not change any settings. i reset it again and here is the export; however i have the same issue when i use masquerade. if i just add the port to the bridge - then i get the full speed. but this is not an ideal solution for me. # nov/19/2021 16:4...

ok - so if i dont use masquerade and just add the port to the bridge and use the same ip range i can get 800Mbps downloads, so it is something happening after, i use the masquerade function.

i reset it again and tested without any vlans,

Here is the interface connected to the modem

Hi,

it is currently set to autonegotiate with advertise selected all the way to 1000M full - it is like this for all ports.

im using ETH4

Hi There, I have a 5g ZTE modem with 2 LAN ports. I have connected to an old routerboard i have (951G), if i connect my laptop via LAN to the ZTE modem i can get 700Mbps, if i connect to the mikrotik only 70. I have tried to hard reset the router and it does not make a difference. On the modem then ...

Hi, thanks for your response, To answer: The PC's are all connected to the CSS Both bonds are 802.3ad The speeds are indeed MB/s Additionally all our cabling is Cat6 and all GigE NIC's i had a look at MTU settings and on the NAS it is set to 1500 - as you said it seems to be a configuration setting ...

further to my previous email if I transfer between 2 PC's across the network I get around 200MB/s speed if I connect my MacBook (with SSD) direct to NAS I get 80-90MB/s I don't understand why my performance to the NAS is so poor over the network - I can transfer files between computers over the netw...

Hi I could do with some help. office NAS - VLAN40 office PC - VLAN20 office NAS is connected to CSS via bonded connection CSS is connected to CCR1016 via bonded connection with this configuration my transfer speed between PC and NAS is around 10MB/s If I edit the NAS ports to be on VLAN20 my transfe...

hi there I have a strange issue. hardware being used CRS109 (AP01) devices RB969 (AP02) CRS is caps manager. what is happening is that wireless is working completely fine. if there is a power cut (this has been happening quite a bit in our area due to weather) then the CRS will correctly provision t...

Hi there, I have a number of rules in mangle. what I am finding is that if i set the in interface to reflect the correct vlan it does not mark the packets. but if I enter the IP address range in the source address fail and remove the interface then it works fine.\ I have ip firewall for vlan and ip ...

Hi there I have recently implemented some vlans I am also using capsman. Since I have done this I have a weird situation 1. Can’t add printers (from different VLAN) however I can ping them and I can also open the webgui for the printer from the same computer. I am manually entering the correct IP ad...

i have two devices that i want to function as dhcp relays. what is the best way to configure this as on the dhcp server you can only determine one relay.

thanks

seeing as your site is http you can use web proxy, go to web proxy and enable it. set max cache size to NONE put your two sites in the allow list then add a last one which is DENY. this will allow only your sites and block all others. then in your NAT you add a dstnat protocol tcp - dstport 80 then ...

ah i see i put the wrong vlans in the AP - sorry been messing around so long that i made a silly mistake. the trunk is working now. a couple of questions: 1. with this config will all traffic on eth02 for example be tagged as vlan10? 2. should all the vlan communicate with each other by default, or ...

Hi There

Sorry to cross post but no one is answering in the beginner forum.
if someone can please help me....
http://forum.mikrotik.com/viewtopic.php ... 65#p470365

AP Config # NAME TYPE ACTUAL-MTU L2MTU 0 R ether1 ether 1500 1598 1 S wlan-guest wlan 1500 1600 2 S wlan-lan wlan 1500 1600 3 wlan1 wlan 1500 1600 4 R bridge-ap bridge 1500 65535 5 R bridge-guest bridge 1500 1594 6 R bridge-lan bridge 1500 1594 7 R bridge-management bridge 1500 1594 8 RS vlan10-e01 ...

Hi I have tried to setup the trunk to ap but from the AP i can only ping my lan bridge address when in theory i should be able to ping my guest bridge address as well. can someone please help me CCR config # NAME TYPE ACTUAL-MTU L2MTU 0 R 01-officetrunk ether 1500 1590 1 RS 02-officeHub ether 1500 1...

here is a bad drawing of what i am trying to achieve.

hi there, i am a newbie but trying hard and i think i made a mistake in getting a CCR and not a CRS. hopefully someone can tell me if i need to get a CRS or if i can make this work. basically i want to set eth01 to trunk vlan 10,20,30 (switch on another floor) eth02 to trunk vlan 10,30 (cAP2n access...

you can use mangle in the firewall tab. put your source ip adress go to action tab choose mark routing then make routing mark "wan1" now go to routes make route to 0.0.0.0/0 gateway 192.168.5.1%(YOUR WAN1 INTERFACE NAME) (the % forces it to use that interface) routing mark "wan1"...

Hi

Thank you for all the advice. I actually just started again with rudios advice and everything works now.
Thanks again

Hi there

I changed: To
But all that happen is no internet access and I can still talk across subnets.

Hi, Hope someone can help me with what is probably a very simple problem I have a few subnet on my router - it is operating as follows 192.168.0.x - Life school - network of about 40 students - can connect to WAN (restricted) 192.168.1.x - tamil uplink - can connect to WAN 192.168.88.x - office netw...

Hi I am using a RB750g i have reluctantly connected one of my servers (10.201.2.242) to allow another device that sits on the local network (10.201.2.243) to communicate through port 11730 and 1482 I do not want ip 10.201.2.242 to: a. be able to access the internet b. be able to receve external traf...