Community discussions

MUM Europe 2020

Search found 25 matches

by error216216
Mon Dec 11, 2017 8:43 pm
Forum: Beginner Basics
Topic: Connect two 3G modems simoultaneously
Replies: 0
Views: 222

Connect two 3G modems simoultaneously

Can someone please help me with the configuration of the second ppp connection? I have two 3g modems connected: /system resource usb print # DEVICE VENDOR NAME SPEED 0 1:1 Linux 3.3.5 ehci_hcd RB400 EHCI 480 Mbps 1 1:2 USB2.0 Hub 480 Mbps 2 1:3 HUAWEI Technology HUAWEI Mobile 480 Mbps 3 1:4 ZTE,Inco...
by error216216
Sun Jun 07, 2015 2:38 am
Forum: Beginner Basics
Topic: Point to Internal DNS server
Replies: 9
Views: 2295

Re: Point to Internal DNS server

How did you set that last part up? I also have the CCR doing NAT to redirect any stray DNS requests back to the .5 box. This is how I redirect all DNS requests to the mikrotik router so the client uses the mikrotik DNS insted of some manually entered DNS on the client's device: /ip firewall nat add...
by error216216
Sun Apr 05, 2015 5:18 pm
Forum: Beginner Basics
Topic: Super tricky setup - 2 IPS with 3 static IPs and 2 local networks
Replies: 3
Views: 963

Re: Super tricky setup - 2 IPS with 3 static IPs and 2 local networks

Create 2 virtual interfaces in metarouter and bridge them to ether1, create 2 meta routers and add vif1 to mr1 and vif2 to mr2. Create another 2 virtual interfaces and assign vif3 to mr1 and vif4 to mr2 in mr1: add to ether1(vif1) ip 10.10.10.104 with desired mac add to ether2(vif3) ip 192.168.10.1/...
by error216216
Sun Apr 05, 2015 6:51 am
Forum: Beginner Basics
Topic: Strange behaviour
Replies: 0
Views: 351

Strange behaviour

I noticed that I did not have internet on wireless so I started to investigate, devices got DHCP lease when connected to wireless but did not respond to ping from router or from device to router. After checking the config, disabled/enabled wlan interface, removed/added to bridge, set ip to wlan inte...
by error216216
Tue Dec 23, 2014 12:50 am
Forum: Beginner Basics
Topic: Remote access
Replies: 7
Views: 1472

Re: Remote access

Have you opened the 22 port in the firewall for all interfaces? /ip firewall filter add chain=input comment=SSH dst-port=22 protocol=tcp place-before=0 For PPTP: add chain=input comment="pptp port input chain" dst-port=1723 protocol=tcp place-before=0 add chain=input comment="pptp auth protocol" pro...
by error216216
Mon Dec 08, 2014 1:41 am
Forum: Beginner Basics
Topic: can we redirect pppoe users to a pre-defined url or web page
Replies: 1
Views: 733

Re: can we redirect pppoe users to a pre-defined url or web

Here's how I would do it: Add a filter that adds the IP trying to access port 80 for the first time to an Advertisment list: #Replace 192.168.99.0/24 with subnet that covers PPPOE client pool or regular client subnet it applies to everyone #Address list timeout is the time for witch the client will ...
by error216216
Fri Dec 05, 2014 1:26 am
Forum: Beginner Basics
Topic: How to assign Public Ip to PPoe users?
Replies: 2
Views: 705

Re: How to assign Public Ip to PPoe users?

You can try 1:1 mapping to the client's fixed private address:

http://wiki.mikrotik.com/wiki/Manual:IP ... :1_mapping
by error216216
Fri Dec 05, 2014 12:56 am
Forum: Beginner Basics
Topic: Need help with forcing DNS with PCC setup
Replies: 1
Views: 607

Re: Need help with forcing DNS with PCC setup

You have to add this in mangle rules :
/ip firewall mangle
add chain=prerouting dst-port=53 protocol=udp place-before=0
add chain=prerouting dst-port=53 protocol=tcp place-before=0
All DNS traffic should be redirected to 192.168.88.1.
by error216216
Thu Dec 04, 2014 11:47 pm
Forum: Beginner Basics
Topic: Subnet and Routing
Replies: 1
Views: 642

Re: Subnet and Routing

The static rule is not correct, is says if traffic wants to get to subnet 192.168.1.0/24, send it to ip 192.168.20.1 but this ip is not part of that subnet and being on the same device it clearly does not have another route to use, anyway... The mikrotik creates the rules for you, you should have di...
by error216216
Thu Dec 04, 2014 10:53 am
Forum: Beginner Basics
Topic: VPN PPTP
Replies: 3
Views: 652

Re: VPN PPTP

If I understood correctly you want the devices from another location to be in the same broadcast as the local ones, I have a working config that does exactly that, the only thing that it will only work between mikrotiks, if you try to connect with a PC to the profile that has bridge it will give an ...
by error216216
Thu Dec 04, 2014 3:55 am
Forum: Beginner Basics
Topic: Schedule script not working for new pppoe clients
Replies: 2
Views: 694

Re: Schedule script not working for new pppoe clients

When setting a variable, don't use the $ in front of it. Remove these and see if it works... :set $ lunaclient [:pick [ppp secret get $i comment] 0 2]; :set $ username [ppp secret get $i name]; :set $ password [ppp secret get $i password]; On a practical note, you could simplify the code by using :...
by error216216
Thu Dec 04, 2014 3:27 am
Forum: Beginner Basics
Topic: Xbox360 NATing imposible on RB750UP with V6.22
Replies: 5
Views: 1311

Re: Xbox360 NATing imposible on RB750UP with V6.22

Ok, first you have to open the router's page by writing the ip address of the router in the address bar of your browser, I assume it's 192.168.1.1, you can find it by looking at what gateway any device gets from dhcp. Then click on WInbox and a program will download, after that fill the connect to w...
by error216216
Thu Dec 04, 2014 2:26 am
Forum: Beginner Basics
Topic: To see wireless clients signal
Replies: 3
Views: 878

Re: To see wireless clients signal

From terminal with: /interface wireless registration-table pr Or login via winbox or web and in the quick set tab you have a wireless clients section with nice little signal lines or go to wireless->registration table and you see a list of the clients and the signal in dBm and other usefull stuff.
by error216216
Thu Dec 04, 2014 1:55 am
Forum: Beginner Basics
Topic: Device recommendation for 70+ wireless users
Replies: 8
Views: 2471

Re: Device recommendation for 70+ wireless users

Thank you all for the replys, the sollution I finnaly went for is a RB951G-2HnD because it was cheap and I could use it in other places if it did not work and on its own it handled 40 simoultaneous clients on a slow night without too much stress, i have not monitored the device after, no one complai...
by error216216
Thu Dec 04, 2014 1:25 am
Forum: Beginner Basics
Topic: Increase PPPoE client rate limit
Replies: 1
Views: 521

Re: Increase PPPoE client rate limit

Of course, add a new simple queue rule with source adress being a subnet that covers pppoe pool with unlimited settings at first, /queue simple add target=192.168.99.0/24 then add a new traffic monitor rule for the Wan and set the limit above you would like the magic to happen, and add some code to ...
by error216216
Thu Dec 04, 2014 12:31 am
Forum: Beginner Basics
Topic: Schedule script not working for new pppoe clients
Replies: 2
Views: 694

Schedule script not working for new pppoe clients

Hello, I have a script that I use to read info from PPPOE client list and send it to them via SMS, disable the account etc. And it does not work for newly added clients. I have simplified the script and added some logging info to it for debugging, the thing is that after reboot everything works, if ...
by error216216
Sat Nov 22, 2014 3:28 am
Forum: Beginner Basics
Topic: Access to local web server by its dns name
Replies: 2
Views: 983

Re: Access to local web server by its dns name

Well you can try to add a DNS rule in the router's DNS Static rules with: /ip dns static add address=192.168.0.2 name=www.example.com This way if your computer has the router's IP in the DNS section of your computer's network configuration, and nothing else, when you will type http://www.example.com...
by error216216
Sat Nov 22, 2014 3:08 am
Forum: Beginner Basics
Topic: NAT Reflection + Dynamic DNS
Replies: 1
Views: 1902

Re: NAT Reflection + Dynamic DNS

Well the forwarding seems ok but I don't understand why you have 2 masquerade rules? Do you have 2 ISP connections, one on interface UniFi-Internet and one on ether1-gateway? if not, remove the one that is not valid, you should also remove the to-addresses=0.0.0.0 from rule 0, I don't see it's usefu...
by error216216
Sat Nov 22, 2014 2:36 am
Forum: Beginner Basics
Topic: Can't access router board from winbox
Replies: 3
Views: 1215

Re: Can't access router board from winbox

Have you tried to disable your windows firewall and see if it works? If it does you have to add winbox to the windows firewall, don't forget to turn it on again after the test.
by error216216
Fri Nov 21, 2014 7:13 am
Forum: Beginner Basics
Topic: Loadbalancing multiple DHCP assigned Wan Interfaces to LAN
Replies: 4
Views: 2516

Re: Loadbalancing multiple DHCP assigned Wan Interfaces to L

Ok, I personnaly use PCC load balanceing because I have a connection that is slower and one that is faster and I want the users to use bouth ISP's not be assigned for one day only to one but if NTH load balanceing is the way you want to go, here's the mangle script for 3 connections: / ip firewall m...
by error216216
Tue Nov 18, 2014 3:28 am
Forum: General
Topic: https problem on hotspot
Replies: 97
Views: 93644

Re: https problem on hotspot

my solution to this long time problem as high percentage of browsers home pages are set to google.com add this expression to your walled garden in the host field :^www\.google\.com$ with port 443 now when they are directed to https://google.com the google page will load instead of an error, Better ...
by error216216
Mon Aug 25, 2014 8:01 pm
Forum: Beginner Basics
Topic: Device recommendation for 70+ wireless users
Replies: 8
Views: 2471

Device recommendation for 70+ wireless users

Hello, I have worked with RB2011UiAS-2HnD-IN before but not with so many wireless devices and I wanted to order this model for a nightclub that has a lot wireless users 70+ I approximate, most of them being mobile devices witch will not make a lot of traffic most of them will just stay connected and...
by error216216
Thu May 29, 2014 5:07 pm
Forum: Beginner Basics
Topic: Struggling with Port Forwarding
Replies: 5
Views: 1502

Re: Struggling with Port Forwarding

This is how I would do it: First two firewall rules: ip firewall filter add chain=input protocol=tcp dst-port=3389 action=accept ip firewall filter add chain=forward protocol=tcp dst-port=3389 action=accept This allows all traffic on 3389 to be allowed to input and forward chain and then once it rea...
by error216216
Fri May 23, 2014 3:53 pm
Forum: Beginner Basics
Topic: Camera access from outside my network
Replies: 3
Views: 778

Re: Camera access from outside my network

You say that you don't have public ip adresses, in this case you cannot access youre camera from the internet, if the ip that you're ISP is giveing you is public you have to add this rule in the terminal: ip firewall nat add action=dst-nat to-addresses=y.y.y.y to-ports=z chain=dstnat protocol=tcp ds...
by error216216
Fri May 23, 2014 3:23 am
Forum: Beginner Basics
Topic: Best CPU efficient NAT configuration for low-cost routers
Replies: 1
Views: 690

Best CPU efficient NAT configuration for low-cost routers

Hello, My ISP provides a 700Mib connection via SFP tested with a directly conected PC. I have bought a RB2011UiAS-2HnD-IN thinking that a 600Mhz CPU will handle this traffic, i'm in tests at the moment and for now i just want to obtain the best results for the following scenario, after that i will e...