Community discussions

Search found 13 matches

by digidax
Fri Apr 21, 2017 10:12 am
Forum: Wireless Networking
Topic: Bridge port received packet with own address as source, probably loop
Replies: 44
Views: 39347

Re: Bridge port received packet with own address as source, probably loop

No, both configurations are done from scratch with default settings first after the problems are coming with the news ROS. Editing of the Neighbor Discovery setting have not solve the problem. But setting on both units (AP and CPE) the MAC address of the unit's wireless interface as Admin MAC addres...
by digidax
Thu Apr 20, 2017 3:20 pm
Forum: Wireless Networking
Topic: Bridge port received packet with own address as source, probably loop
Replies: 44
Views: 39347

Re: Bridge port received packet with own address as source, probably loop

Hi,
Neighbor Discovery setting before:
bridge1 => enabled
ether1 => enabled
wlan1 => disabled

now set to:
bridge1 => enabled
ether1 => disabled
wlan1 => disabled

Thanks. I will report the result after 24 h monitoring.
best regards, Frank
by digidax
Thu Apr 20, 2017 10:16 am
Forum: Wireless Networking
Topic: Bridge port received packet with own address as source, probably loop
Replies: 44
Views: 39347

Re: Bridge port received packet with own address as source, probably loop

Same problem on CPE with ROS 6.38.5
AP with ROS 6.38.5 als AP bridge, CPE configured as station bridge. bridge1 with wlan1 and ether1

Only this one CPE is connected with the AP, on eth of the CPE a laptop is connected. No switches are playing in this setup.

thanks, Frank
by digidax
Mon Jul 06, 2015 7:29 am
Forum: Wireless Networking
Topic: wireless scan without wireless connetion interruption
Replies: 3
Views: 496

Re: wireless scan without wireless connetion interruption

Thanks for the hint.
It's a option that will work for me.
Best regards Frank
by digidax
Sun Jul 05, 2015 10:33 pm
Forum: Wireless Networking
Topic: wireless scan without wireless connetion interruption
Replies: 3
Views: 496

wireless scan without wireless connetion interruption

Hi, I'm connected to a CPE device using a wireless connection. If I do start a wireless scan on this CPE device, der wireless connection to the AP is interrupted. On DD-WRT it's possible to do this. I need this feature to see, if near the CPE another system using the same wireless channel like the C...
by digidax
Sat Aug 16, 2014 4:08 pm
Forum: General
Topic: Mark packet
Replies: 3
Views: 873

[solved] Re: Mark packet

Thanks, it's working.
My bad was the wrong mark direction of the source port. Now everything is working fine.

thanks, Frank
by digidax
Sat Aug 16, 2014 1:46 pm
Forum: General
Topic: Mark packet
Replies: 3
Views: 873

Re: Mark packet

did noboady has a solution?
by digidax
Wed Jul 30, 2014 4:39 pm
Forum: General
Topic: Mark packet
Replies: 3
Views: 873

Mark packet

Hello, have configured NAT, Wireless is a client of an AP, LAN 192.168.1.0/24 on ethernet port 3. I see in Torch such connection: Src: 192.168.1.171:52203 Dst: 100.100.100.100:5000 The src host has initiated a ssh connection to dst and loads from the dst host data down. (Tx Rate: 21 MBit, Rx Rate 17...
by digidax
Wed Jul 23, 2014 4:41 pm
Forum: General
Topic: Feature requests
Replies: 1160
Views: 207596

Re: Feature requests

If I have opened a firewall rule, a Button to clone this rule.

I have a lot of INPUT rules, which are only different by the src IP Address.
So I can clone the rule, change the SRC IP and apply the rule.
Webmin (www.webmin.com) have it implemented for the firewall settings.

thanks
Frank
by digidax
Wed Jul 23, 2014 4:28 pm
Forum: Beginner Basics
Topic: Quick Set: AP Mode
Replies: 7
Views: 2769

Re: Quick Set: AP Mode

okay, thanks for the hint. The serial cable will be my new (old) friend.
I have now setup the AP step by step and it's working very well.

The work around with the scheduler is a very good idea. This is a safe fall back to the local network for acessing the bridge.
Thanks.

best regards
Frank
by digidax
Mon Jun 02, 2014 10:42 pm
Forum: Beginner Basics
Topic: Quick Set: AP Mode
Replies: 7
Views: 2769

Re: Quick Set: AP Mode

no, have not used connectivity via MAC. Will try it next week.
Thanks for the useful hints, have now many ways to play.

thank
Frank
by digidax
Sun Jun 01, 2014 11:39 pm
Forum: Beginner Basics
Topic: Quick Set: AP Mode
Replies: 7
Views: 2769

Re: Quick Set: AP Mode

Yes directly via Webfig. Laptop has 192.168.88.21/24
Ethernet port with PoE label is used. Power not via PoE injector.

Thank, Frank
by digidax
Fri May 30, 2014 10:28 am
Forum: Beginner Basics
Topic: Quick Set: AP Mode
Replies: 7
Views: 2769

Quick Set: AP Mode

Hello, I have setup a PTP Bridge with AP (server/AP) and client (Client/CPE) within a few click without any problems. No I want to change to AP bridge mode (to connect more than one client) and have set the following: - AP Quickset - Mode: bridge - Address Acquisition: Static - IP Address: 192.168.8...