Community discussions

Search found 211 matches

by kiaunel
Wed Mar 20, 2019 1:07 am
Forum: Beginner Basics
Topic: Problems config HAP AC as Home Internet Router PPPOE
Replies: 1
Views: 198

Re: Problems config HAP AC as Home Internet Router PPPOE

Look on system.. Packages if you have ppp enabled of it is at all there.

Sent from my BLA-L29 using Tapatalk

by kiaunel
Tue Mar 19, 2019 11:29 pm
Forum: Beginner Basics
Topic: public access
Replies: 8
Views: 744

Re: public access

First of all do not post your public address,
second : try export instead of screen capture,
third: use incoming interface instead of ip address
by kiaunel
Tue Mar 19, 2019 11:20 pm
Forum: Beginner Basics
Topic: public access
Replies: 8
Views: 744

Re: public access

Post your dst nat rule
/ip firewall nat add action=dst-nat chain=dstnat dst-port=9000 in-interface=ether1 protocol=tcp to-addresses=172.16.0.233 to-ports=9000
You can see here you can use incoming interface instead of destination ip
by kiaunel
Tue Mar 19, 2019 11:17 pm
Forum: Beginner Basics
Topic: Hotspot port number [SOLVED]
Replies: 3
Views: 351

Re: Hotspot port number [SOLVED]

This usualy is done with htaccess in your web server configuration, directly on webserver
by kiaunel
Tue Mar 19, 2019 10:59 pm
Forum: Beginner Basics
Topic: How to renew ip address when reconnecting pppoe
Replies: 5
Views: 492

Re: How to renew ip address when reconnecting pppoe

Reduce keepallive timeout and alocate ip from pppoe-pool
by kiaunel
Tue Mar 19, 2019 10:56 pm
Forum: Beginner Basics
Topic: Hotspot port number [SOLVED]
Replies: 3
Views: 351

Re: Hotspot port number [SOLVED]

It is not clear, for me, what you want.
The purpose of hotspot is to catch connections generated in your lan and forward them to a hotspot login page to force users authentificate themselfs. Why would you do that from wan?
by kiaunel
Mon Mar 18, 2019 4:26 pm
Forum: Beginner Basics
Topic: CCR1016-12G VPN to discover ubiquiti radios for UNMS
Replies: 4
Views: 462

Re: CCR1016-12G VPN to discover ubiquiti radios for UNMS

Setup VPN as ethernet mode and it will work. I use ehernet to discover mikrotik devices and works just fine. No doubt on ubiquity will work too

Sent from my BLA-L29 using Tapatalk

by kiaunel
Tue Mar 12, 2019 11:34 pm
Forum: Beginner Basics
Topic: OVPN disconnect after few seconds
Replies: 9
Views: 428

Re: OVPN disconnect after few seconds

Tue Mar 12 22:22:39 2019 Set TAP-Windows TUN subnet mode network/local/netmask = 172.16.6.0/172.16.6.10/255.255.255.0 [SUCCEEDED] Tue Mar 12 22:22:39 2019 Notified TAP-Windows driver to set a DHCP IP/netmask of 172.16.6.10/255.255.255.0 on interface {319F348A-FC54-493B-A954-D9B0308654D6} [DHCP-serv...
by kiaunel
Tue Mar 12, 2019 8:47 pm
Forum: Beginner Basics
Topic: OVPN disconnect after few seconds
Replies: 9
Views: 428

Re: OVPN disconnect after few seconds

Post your client connection log
by kiaunel
Tue Mar 12, 2019 8:17 pm
Forum: Beginner Basics
Topic: OVPN disconnect after few seconds
Replies: 9
Views: 428

Re: OVPN disconnect after few seconds

Add this in your vpn client config if you are using windows :
route-method exe
redirect-gateway
by kiaunel
Mon Mar 11, 2019 7:28 pm
Forum: Beginner Basics
Topic: ICMP Drop
Replies: 4
Views: 321

Re: ICMP Drop

Think like this :
How can routeros imagine how many packets will receive in future?
If it will receive 100 it will have to drop 10
If it will receive 10 it will have to drop 1
if it will receive 1000 it will have to drop 100
How can some os or you predict this?
by kiaunel
Mon Mar 11, 2019 7:14 pm
Forum: Beginner Basics
Topic: Hotspot wifi and Lan users
Replies: 13
Views: 1008

Re: Hotspot wifi and Lan users

It is very simple. Your topology is totally wrong. To some wireless clients to get access to the hotspot interface you had to assing uplink ether port on the hotspot device. So hotspot pool is everywhere in your network So , first Move the two cables from the switch to lan ports of Mikrotik Hotspot ...
by kiaunel
Sun Mar 10, 2019 9:55 pm
Forum: General
Topic: want to know suitable wifi router for me
Replies: 5
Views: 393

Re: want to know suitable wifi router for me

Hotspot +UserManager is all that you need, depending of your are where users will connect you will need one or more accesspoints

Sent from my BLA-L29 using Tapatalk

by kiaunel
Sat Mar 09, 2019 8:46 am
Forum: Beginner Basics
Topic: checking for update
Replies: 2
Views: 288

Re: checking for update

And then check of you have proper dns and default route setting on mikrotik

Sent from my BLA-L29 using Tapatalk

by kiaunel
Fri Mar 08, 2019 11:40 pm
Forum: Beginner Basics
Topic: Control kids iPad usage time
Replies: 9
Views: 1040

Re: Control kids iPad usage time

I used usermanager+hotspot for this. This worked very good in my house :)
by kiaunel
Fri Mar 08, 2019 10:28 pm
Forum: Beginner Basics
Topic: OVPN not responding [SOLVED]
Replies: 1
Views: 253

Re: OVPN not responding [SOLVED]

Mikrotik open VPN server does not support udp and lzo. Change the config to tcp and remove lzo line

Sent from my BLA-L29 using Tapatalk

by kiaunel
Wed May 04, 2016 6:19 am
Forum: Beginner Basics
Topic: VPN PPTP how to access local machine?
Replies: 2
Views: 654

Re: VPN PPTP how to access local machine?

Are you using routed mode or bridged? Only in bridge mode you can access windows shares.
by kiaunel
Thu Apr 28, 2016 7:12 am
Forum: Beginner Basics
Topic: Drop DNS server or request
Replies: 7
Views: 1383

Re: Drop DNS server or request

You are dropping source-port not dst-port. Also, make sure you are not using fasttrack. This may ignore your drop rules.
by kiaunel
Wed Apr 27, 2016 10:15 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

Routeros use 192.168.88.1 as default ip but you can change it with 192.168.0.1 as your ubnt. But keep in mind if ap witch connect with sxt is not mikrotik you will not be able to use as a bridge.
by kiaunel
Wed Apr 27, 2016 7:22 am
Forum: Beginner Basics
Topic: [SOLVED] Official Package Source Mirrors
Replies: 2
Views: 7217

Re: Official Package Source Mirrors

Go to System-- Packages--Check for updates.
by kiaunel
Tue Apr 26, 2016 9:20 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

There is something both are missing. I can replicate your problems, in a test lab, only if pppoe interface is not connected. I don`t have the time and mod to setup a pppoe server now but please be sure your pppoe interface is still conected.
by kiaunel
Tue Apr 26, 2016 7:52 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

Ok. First good step. Now in ip -- firewall on nat tab change masquerade rule out interface to match out-interface pppoe-out1. Second. add dns server in ip -- dhcp-server in network tab after gateway input dns server 8.8.8.8. This will assing dns server to dhcp clients. Then in filter rules change de...
by kiaunel
Tue Apr 26, 2016 7:07 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

Ok, you mess up thing. Lets take one by one. 1. change 192.168.1.20/32 from ether1 to 192.168.1.25/24, then you can access ubnt if needit. 2. Now, as ubnt is bridge there is not an dhcp server on it. I still can not understand how do you connect to internet. If you was using ppoe then configure your...
by kiaunel
Tue Apr 26, 2016 6:19 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

on first look i can not see something wrong in your config. To access ubnt assing to eth1 an ip 192.168.1.25 and you will be able to connect to ubnt. Post your ip and routes here i p route print ip address print Make sure your computer is configured proprely. Post an tracereoute response to 8.8.8.8 ...
by kiaunel
Tue Apr 26, 2016 4:20 pm
Forum: Beginner Basics
Topic: Airgrid in bridge and RB951 as pppoe client,not working?
Replies: 11
Views: 1428

Re: Airgrid in bridge and RB951 as pppoe client,not working?

post your mikrotik config. Use export hide-sensitive command.
by kiaunel
Tue Apr 26, 2016 3:43 pm
Forum: Beginner Basics
Topic: Can't connect between 2 subnet in 2 eth
Replies: 5
Views: 868

Re: Can't connect between 2 subnet in 2 eth

Post your config here. Use export commnad:
export hide-sensitive
by kiaunel
Tue Apr 26, 2016 3:38 pm
Forum: Beginner Basics
Topic: Basic Wireless Client
Replies: 2
Views: 630

Re: Basic Wireless Client

If the ap is not Mikrotik you will not use station bridge becouse it il not work. Station bridge is only for mikrotik ap. You will have to use station mode with your groove setup as a router. No bridging is posible in this situation. To avoid double nat you can use static route on first router if it...
by kiaunel
Mon Apr 25, 2016 2:54 pm
Forum: Wireless Networking
Topic: PtMP: SXT2 -> 2x SXT2 Lite not working (Bridge -> 2xStation Bridge)
Replies: 5
Views: 717

Use ap bridge mode on sxt2

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Sat Apr 23, 2016 11:14 pm
Forum: Beginner Basics
Topic: How i can be watching AP devices in RB2011
Replies: 3
Views: 620

Re: How i can be watching AP devices in RB2011

With snmp you can do it. The OID is :
interface wireless print oid
client-count=.1.3.6.1.4.1.14988.1.1.1.3.1.6.9 
You can monitor it with cacti or dude.
by kiaunel
Thu Apr 21, 2016 6:34 am
Forum: Beginner Basics
Topic: Assigning one port out of NAT
Replies: 3
Views: 633

Re: Assigning one port out of NAT

I doubt it will work. but you can try this : like you said... ether1 with isp ether2 to stb , ether1,2 in bridge-isp, then depend how you connect add a dhcp client or pppoe connection to bridge isp. Again, i doubt it will work becouse i think your isp use tagged vlans. If not working like this you w...
by kiaunel
Wed Apr 20, 2016 10:34 pm
Forum: Beginner Basics
Topic: Assigning one port out of NAT
Replies: 3
Views: 633

Re: Assigning one port out of NAT

I don`t know what configuration is using your isp but you can create a bridge, let`s say bridge-isp with two ports, , let`s say ether 2 and ether 3 added to the bridge interface. Port 2 will be isp cable and port 3 will be STB wan cable . Then ether 1 set as wan connected to lan port of STB and ethe...
by kiaunel
Wed Apr 20, 2016 10:27 pm
Forum: General
Topic: MikroTik Configuration With PPPoE WAN
Replies: 4
Views: 2973

Re: MikroTik Configuration With PPPoE WAN

I don`t know what features has the router but setting it as bridge will make it transparent, also will disable any services running on it, it will act as a switch between mikrotik and your isp.
by kiaunel
Wed Apr 20, 2016 3:18 pm
Forum: General
Topic: MikroTik Configuration With PPPoE WAN
Replies: 4
Views: 2973

Re: MikroTik Configuration With PPPoE WAN

Setup your isp router as a bridge. Then, the simple way is to enter quick config on mikrotik and setup your pppoe connection there. This way all your firewall rules will adapt to pppoe interface and not to ether1 , leaving your router exposed to the internet. The other way is to set up pppoe connect...
by kiaunel
Wed Apr 20, 2016 1:08 pm
Forum: Wireless Networking
Topic: Wireless DHCP and Net problem
Replies: 5
Views: 686

Re: Wireless DHCP and Net problem

You`re welcome.
by kiaunel
Wed Apr 20, 2016 6:48 am
Forum: General
Topic: DNS pegging CPU to 100%?
Replies: 9
Views: 1749

Make sure you deny DNS requests from outside. In filter rules make an input deny rule for TCP/UDP on port 53

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Wed Apr 20, 2016 6:45 am
Forum: Wireless Networking
Topic: Wireless DHCP and Net problem
Replies: 5
Views: 686

Remove the bridge... You don't need it in this setup, create a dhcp server on wlan1 with specific subnet, make sure your clients on wifi get proper ip configuration, masquerade those subnets , make filter rules in forward for wifi subnet to forward only to ether1 and you will be fine. Sent from my L...
by kiaunel
Fri Apr 08, 2016 6:50 am
Forum: Wireless Networking
Topic: hAP AC wireless problems
Replies: 7
Views: 1885

Use wireless-cm2 instead of wireless-fp and You will have both wireless cards. În ac cards there is no power settings thats why your tab is empty.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Thu Apr 07, 2016 3:27 pm
Forum: Wireless Networking
Topic: Low Bandwith with SXT ac
Replies: 8
Views: 1057

Fitst of all -48 is a little to high signal. Try to set antena gain if you have it 0 to 2-4-6-8-10 on both devices until you get around -55 -60 signal. On these signals I get most stable links. Second if your scan tool does not see interference does not mean there isn't. Try to change channels until...
by kiaunel
Mon Apr 04, 2016 11:04 pm
Forum: Beginner Basics
Topic: PPPOE disconnect until DHCP assigned
Replies: 4
Views: 759

Re: PPPOE disconnect until DHCP assigned

Your problem seems to be this: Apr/02/2016 12:36:56 pppoe,debug vlan6: terminating sessions: interface state changed Somehow your vlan interface goes up and down? Is it assigned to a bridge with dinamic interfaces? May i ask why is pppoe-client assigned to a vlan an not an interface? Post your confi...
by kiaunel
Sun Apr 03, 2016 7:08 am
Forum: Beginner Basics
Topic: Plz MikroTik , give me solution for netcut and theft of Mac address ?
Replies: 10
Views: 1919

Re: Plz MikroTik , give me solution for netcut and theft of Mac address ?

1. Set "default-forwarding=no" on your wireless interface...
2. Set arp=reply-only on the interface your customers are connecting to.

3. Set add-arp=yes for the DHCP-Server.

With these three settings, your router will ignore any client who had not obtained an IP address from the DHCP server.
by kiaunel
Sat Apr 02, 2016 3:38 pm
Forum: Beginner Basics
Topic: PPPOE disconnect until DHCP assigned
Replies: 4
Views: 759

Re: PPPOE disconnect until DHCP assigned

Start looking at logs
Enable dubug pppoe connection logs :
/system logging add topics=pppoe
/system logging add topics=dhcp
then post here some logs regarding disconection.
Also an export config will help to anybody guide you to a solution:
export hide-sensitive
by kiaunel
Sat Apr 02, 2016 9:40 am
Forum: Beginner Basics
Topic: Plz MikroTik , give me solution for netcut and theft of Mac address ?
Replies: 10
Views: 1919

How is your wireless network? Open or encrypted? Who is cloning macs? You can use pppoe , this will force your users to connect with an username and a password and cloning macs will be pointless. Mikrotik has nothing to do with your problem.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Fri Apr 01, 2016 11:36 pm
Forum: Beginner Basics
Topic: VLAN Help
Replies: 6
Views: 1515

Glad You made it.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Fri Apr 01, 2016 6:30 am
Forum: Beginner Basics
Topic: VLAN Help
Replies: 6
Views: 1515

Re: VLAN Help

What does path cost and root path cost mean? Or should I even worry about those in the bridge section?
It is used to set best path on redundand links. Leave it as it is.
by kiaunel
Thu Mar 31, 2016 11:06 pm
Forum: Wireless Networking
Topic: SXT ac - Current TX Power display don't work ?
Replies: 8
Views: 2736

Same situation with RouterBOARD 952Ui-5ac2nD

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Thu Mar 31, 2016 10:46 pm
Forum: Beginner Basics
Topic: VLAN Help
Replies: 6
Views: 1515

Re: VLAN Help

You have to create two vlans, lets say vlan 11 192.168.11.0/24 and vlan 10 for 10.11.10.0/24, Lets say port 24 will be connected to the other mikrotik Remove master interface for it, set it to none. /interface vlan add interface=ether24 name=vlan11 vlan-id=11 add interface=ether24 name=vlan10 vlan-i...
by kiaunel
Wed Mar 30, 2016 10:59 am
Forum: General
Topic: TimeWarner Business IPv6
Replies: 4
Views: 767

You should first ensure that you have successfully connect to ISP on ipv6 level. Maybe they can support you on this. Then you should work on routing your subnet. Maybe they have a dhcp server on ipv6 and you could use dhcp client on ipv6 to get your config. Also I don't think you use correct address...
by kiaunel
Tue Mar 29, 2016 10:54 pm
Forum: General
Topic: Redirect authorized hotspot users to login.html page
Replies: 2
Views: 504

Re: Redirect authorized hotspot users to login.html page

Maybe you should use wallen garden feature and not ip list.
by kiaunel
Tue Mar 29, 2016 12:54 pm
Forum: Beginner Basics
Topic: ISP WAN Ip with public ip block
Replies: 6
Views: 2372

Re: ISP WAN Ip with public ip block

Why use socond router??? Isp give you one ip block routed to your ip. It is simple routing. Assing your wan ip to interface connected to isp and first ip from lan block to lan master interface or bridge if you have one. No need for nat if there are public ips. If they arent you have to nat. If you w...
by kiaunel
Tue Mar 29, 2016 10:49 am
Forum: General
Topic: TimeWarner Business IPv6
Replies: 4
Views: 767

Re: TimeWarner Business IPv6

You have to use 2604:2000:0:8::f:yy3/127 on your isp connected interface and 2600:6000:fxxx::1/64 on lan inter toface. Add default route to isp interface.That /127 is not the best but you will have to live with it. /ipv6 address add address=2604:2000:0:8::f:yy3/127 advertise=no disabled=no eui-64=no...
by kiaunel
Mon Mar 28, 2016 2:24 pm
Forum: Beginner Basics
Topic: Slave interfaces vs Bridge
Replies: 5
Views: 1174

Switch CPU is better.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Mon Mar 28, 2016 8:17 am
Forum: Beginner Basics
Topic: Slave interfaces vs Bridge
Replies: 5
Views: 1174

Bridge use router cpu, slaves use switch cpu for more performance , this is the difference.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Sun Mar 27, 2016 1:11 pm
Forum: Beginner Basics
Topic: Beginners quest: 2 routers, 2 subnets.
Replies: 17
Views: 2090

Yeah, I've missed last part, sorry.

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Sun Mar 27, 2016 1:03 pm
Forum: Beginner Basics
Topic: Beginners quest: 2 routers, 2 subnets.
Replies: 17
Views: 2090

Re: Beginners quest: 2 routers, 2 subnets.

Hi , 1-Unplug your second router !! 2-first you have to setup you first router , if your first router has internet ( you can test it by ping 8.8.8.8 from Tools/Ping) then setup DHCP on first router and be sure it's working,since your modem , first router and first router's hosts are in a same subne...
by kiaunel
Sat Mar 26, 2016 8:17 pm
Forum: Beginner Basics
Topic: Beginners quest: 2 routers, 2 subnets.
Replies: 17
Views: 2090

Yes. Solution 2 i gave to you

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Sat Mar 26, 2016 5:27 pm
Forum: Beginner Basics
Topic: Beginners quest: 2 routers, 2 subnets.
Replies: 17
Views: 2090

You have two options. 1. Make a setup like You described but is the worst situation. I can not know where you are loosing internet conectivity without you describing what did you do . you can use the quick setup feature configure both routers. But in this setup you will have double nat and possible ...
by kiaunel
Sat Mar 26, 2016 2:37 pm
Forum: Beginner Basics
Topic: Accessing a web server [through script]
Replies: 2
Views: 507

Re: Accessing a web server [through script]

Maybe
/tool fetch url="http://www.example.com/" mode=http
will help you
by kiaunel
Sat Mar 26, 2016 2:31 pm
Forum: General
Topic: connect router board 433 with rocket 5 AC
Replies: 1
Views: 326

Re: connect router board 433 with rocket 5 AC

Does your 433 have an ac radio card? If not you can not "see" or discover ac access points.
by kiaunel
Sat Mar 26, 2016 2:21 pm
Forum: Beginner Basics
Topic: Reflash gone wrong
Replies: 4
Views: 604

Re: Reflash gone wrong

What wireless package are you using? If you are on wireless-fp change it to wireless-cm2. On mine i have wlan2 only with cm2
by kiaunel
Thu Mar 24, 2016 12:34 pm
Forum: Beginner Basics
Topic: Help with VLAN configuration
Replies: 1
Views: 563

Re: Help with VLAN configuration

If your Soho switch is not vlan capable you can not use trunk port.You have to connect cable to 5.0/24 directly to mikrotik to isolate that network. Post your firewall rules in forward and your routes, becouse in this config your cameras should connect to dvr by routing. To isolate .5.0/24 network y...
by kiaunel
Wed Mar 23, 2016 6:36 pm
Forum: Beginner Basics
Topic: Problem with Nat port for camera
Replies: 6
Views: 991

How did u nat camera port?

Sent from my Lenovo K50a40 using Tapatalk
by kiaunel
Mon Mar 14, 2016 7:11 pm
Forum: Beginner Basics
Topic: Internet is not working on LAN connected device.
Replies: 4
Views: 786

If you are not connecting with cable în ether2 change your lan ip and dhcp server on bridge

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Mar 12, 2016 10:40 pm
Forum: Beginner Basics
Topic: how to reset dynadish 5?
Replies: 2
Views: 2642

Re: how to reset dynadish 5?

From the manual : Buttons and Jumpers RouterBOOT reset button (RESET, front panel) has three functions: • Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds) • Keep holding for 5 more seconds, LED turns solid, releas...
by kiaunel
Sun Mar 06, 2016 7:40 am
Forum: Beginner Basics
Topic: Device with pre-configured IP address
Replies: 7
Views: 1381

Re: Device with pre-configured IP address

Yes, i said 0.1 not 0.100 :)
by kiaunel
Sun Mar 06, 2016 12:54 am
Forum: Beginner Basics
Topic: Device with pre-configured IP address
Replies: 7
Views: 1381

Post your config


Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Mar 05, 2016 9:34 pm
Forum: Wireless Networking
Topic: repeater - station modes
Replies: 1
Views: 714

Re: repeater - station modes

You have to keep your Eoip tunnel or make in bridge if Ap is not mikrotik.
by kiaunel
Sat Mar 05, 2016 9:22 pm
Forum: Beginner Basics
Topic: Device with pre-configured IP address
Replies: 7
Views: 1381

Re: Device with pre-configured IP address

Add an address on interface connected to alarm system.
ip address add address=192.168.0.1/24 interface=lan network=192.168.0.0
by kiaunel
Wed Mar 02, 2016 7:01 am
Forum: Beginner Basics
Topic: how i configure web proxy RB2011UAS with usb flash disk or sd card ?
Replies: 3
Views: 1418

Re: how i configure web proxy RB2011UAS with usb flash disk or sd card ?

Yes, after you set up proxy make a test by adding ip/port manualy to browser then redirect all your web traffic on proxy to make it transparent. If you realy need it? Only you can have the answer. Depends on what kind of traffic your clients do and what speed is your connection.
by kiaunel
Wed Mar 02, 2016 6:56 am
Forum: Wireless Networking
Topic: Mikrotik Router and Point to MultiPoint Problem
Replies: 2
Views: 568

Are you using station mode on clients? Use station bridge or station wds instead

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Mon Feb 29, 2016 11:13 pm
Forum: Beginner Basics
Topic: how i configure web proxy RB2011UAS with usb flash disk or sd card ?
Replies: 3
Views: 1418

Re: how i configure web proxy RB2011UAS with usb flash disk or sd card ?

Enable "Cache on disk" option under ip -- webproxy.
Make sure your flash drive or sdcard is proprerly detected under files sections as /disk.
by kiaunel
Sun Feb 28, 2016 7:12 am
Forum: Beginner Basics
Topic: Wan port blocks HAP
Replies: 4
Views: 576

Re: Wan port blocks HAP

How do you set up hap? use winbox and paste here export command from terminal.
by kiaunel
Sat Feb 27, 2016 11:06 pm
Forum: Beginner Basics
Topic: One Bridge with different IP addresses
Replies: 5
Views: 614

Re: One Bridge with different IP addresses

I think tv is looking for dlna server only in his subnet so you can not put them in two bridges. As itmethod already said put them in one bridge and other devices in another bridge if this setup suits you.
by kiaunel
Sat Feb 27, 2016 2:31 pm
Forum: Wireless Networking
Topic: Where is Limitation come from for an AP?! , Is it related to cpu and ram of the routerboard device or other issue?!
Replies: 7
Views: 733

The limitation is per radio. There with more clients connected to radio will increase the time to transmit / retransmit data especially for clients with lower signal. So no, using a x86 device will not help. You will have to install several access points. I can not imagine any radio , not only from ...
by kiaunel
Sat Feb 27, 2016 1:11 pm
Forum: Beginner Basics
Topic: Setting other router in pseudo-bridge with DMZ
Replies: 3
Views: 639

You're welcome.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Feb 27, 2016 12:30 pm
Forum: General
Topic: winbox failed to see a brand new RB850Gx2 in neighbors
Replies: 5
Views: 799

Try netinstall, but I doubt if it is brand new is not working.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Feb 27, 2016 8:28 am
Forum: Beginner Basics
Topic: One Bridge with different IP addresses
Replies: 5
Views: 614

Re: One Bridge with different IP addresses

Hello! Scenario: Until recently I used two different Bridges: 1 bridge_WLAN & 1 bridge_local. The Problem is, that i can't connect from my TV to my NAS, which are in different Bridges. I tried to put the WLAN & LAN into 1 bridge and hurray, it works! The "problem" is, that I want to have 2 differen...
by kiaunel
Sat Feb 27, 2016 7:22 am
Forum: General
Topic: Should I buy sxtg 2hnd or any good alternative?
Replies: 8
Views: 576

Re: Should I buy sxtg 2hnd or any good alternative?

And for 10 bucks you can get gigabit version
http://routerboard.com/RBSXTG-5HPnD-SAr2
by kiaunel
Sat Feb 27, 2016 7:13 am
Forum: General
Topic: Should I buy sxtg 2hnd or any good alternative?
Replies: 8
Views: 576

Re: Should I buy sxtg 2hnd or any good alternative?

Using 5ghz band may have less interference in your area. If there are neighbours with routers near you they will be most likely in 2,4 ghz band. So in this situation your transport link will perform better in 5ghz band. you can use 2,4 with omnitik for your local coverage. Also 5hpnd have better spe...
by kiaunel
Fri Feb 26, 2016 11:42 pm
Forum: General
Topic: Should I buy sxtg 2hnd or any good alternative?
Replies: 8
Views: 576

I would use sxt 5hnd if you will not need more than 100 Mb or use one on 5ghz with gigabit land if you need more. Then use one of the omnitik for local coverage. Keep in mind that your friend will not be able to connect directly with their laptops or smartphone to omnitik. They have to use each one ...
by kiaunel
Fri Feb 26, 2016 10:31 pm
Forum: Beginner Basics
Topic: Need help routing ipv6 between LAN clients and WAN, everything else works
Replies: 12
Views: 2339

Re: Need help routing ipv6 between LAN clients and WAN, everything else works

Nothing against HE, but if ISP offers working native IPv6, I'd prefer to use that. You can say that this is not working, but it must be just some misunderstanding. It's a little strange that support would not know how is their config supposed to work, but I'm sure they will eventually find some emp...
by kiaunel
Fri Feb 26, 2016 9:27 pm
Forum: Beginner Basics
Topic: Setting other router in pseudo-bridge with DMZ
Replies: 3
Views: 639

Re: Setting other router in pseudo-bridge with DMZ

Remove bridge-gateway becouse you don`t need more than one port for wan. Then set up a rulle for nat : ip firewall nat add action=masquerade chain=srcnat src-address=lan_subnet/24 This is the very basic to get started Asuming that you have a dhcp-server working proprely on bridge-lan and a dhcp-clie...
by kiaunel
Fri Feb 26, 2016 6:57 am
Forum: Beginner Basics
Topic: pass IPv6 through
Replies: 5
Views: 991

Use he.net. it works good for me.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 26, 2016 6:30 am
Forum: Beginner Basics
Topic: Need help routing ipv6 between LAN clients and WAN, everything else works
Replies: 12
Views: 2339

Re: Need help routing ipv6 between LAN clients and WAN, everything else works

If you realy want ipv6 to work subscribe to he.net. It will be a tunnel but it work great for me.
by kiaunel
Thu Feb 25, 2016 11:20 pm
Forum: Beginner Basics
Topic: ip cloud not working with me
Replies: 1
Views: 500

Re: ip cloud not working with me

If you ping the cloud host the ip resolves with that from your wan interface? There are situations when cloud does not update address after it changes but it can be forced to update.
by kiaunel
Thu Feb 25, 2016 11:17 pm
Forum: Beginner Basics
Topic: RB 750 GL Traffic Monitor
Replies: 2
Views: 685

Re: RB 750 GL Traffic Monitor

There is no tool (from what i know) like SARG for linux squid. The only tool who can help you is torch. But there are only connections/ips.
by kiaunel
Thu Feb 25, 2016 11:09 pm
Forum: Beginner Basics
Topic: Major Network Issues on New RB912UAG-5HPnD
Replies: 2
Views: 534

Re: Major Network Issues on New RB912UAG-5HPnD

Windows clients may do not respond on icmp request due to firewall.
From what you post it should work... Post your config here. Use export command.
by kiaunel
Thu Feb 25, 2016 11:04 pm
Forum: Beginner Basics
Topic: pass IPv6 through
Replies: 5
Views: 991

Re: pass IPv6 through

What kind of ipv6 address is your modem geting? maybe it is link local ipv6. If it like fe80:: the means your modem is ipv6 ready but your isp did not actualy use ipv6.
by kiaunel
Thu Feb 25, 2016 5:36 pm
Forum: Beginner Basics
Topic: Need help routing ipv6 between LAN clients and WAN, everything else works
Replies: 12
Views: 2339

You have to get another ip to ether1 witch will route your /64 subnet. In my case I have a tunnel ( my ISP don't offer ipv6) with 2001:470:xxxx::1 on my tunnel side and 2001:470:yyyy::1/64 assigned to my lab interface. So my clients get IPS from 2001:470:yyyy::1/64 and everything works like it shoul...
by kiaunel
Thu Feb 25, 2016 8:48 am
Forum: Beginner Basics
Topic: Need a place to start with rate limiting inbound traffic
Replies: 4
Views: 593

It is behind mikrotik

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Feb 25, 2016 6:45 am
Forum: Beginner Basics
Topic: Need a place to start with rate limiting inbound traffic
Replies: 4
Views: 593

Re: Need a place to start with rate limiting inbound traffic

Keep in mind that if you use fasttrack connection it may baypass your queques.
In my config this one is simple and works.
/queue simple
add max-limit=3M/0 name=para target=10.10.9.3/32
by kiaunel
Thu Feb 25, 2016 6:34 am
Forum: Beginner Basics
Topic: Isolated network
Replies: 7
Views: 1443

Re: Isolated network

This...without NAT Masquerade rule on your private subnet, you wont be able to go on internet... I don't know why but without NAT masquerade I have internet connection in the private subnet, that is annoying meand i don't know how to fix it. /ip firewall nat add action=masquerade chain=srcnat comme...
by kiaunel
Wed Feb 24, 2016 8:04 am
Forum: Beginner Basics
Topic: Port Opening Issue
Replies: 3
Views: 517

Re: Port Opening Issue

Use a firewall rule like this:
ip firewall nat add action=dst-nat chain=dstnat dst-port=8080 in-interface=ether1 protocol=tcp to-addresses=device lan ip to-ports=8080
by kiaunel
Wed Feb 24, 2016 7:33 am
Forum: Beginner Basics
Topic: Cannot get port forwarding to work
Replies: 10
Views: 1881

Re: Cannot get port forwarding to work

Post your firewall rules here.
In terminal :
ip firewall nat export
by kiaunel
Wed Feb 24, 2016 6:30 am
Forum: Beginner Basics
Topic: Isolated network
Replies: 7
Views: 1443

Re: Isolated network

You have to create two dhcp-server, one for local and one for private, assigned to separate bridges, two ip pools one for each dhcp server, then restrict your masqurade rule to only specific subnet allowed to internet.
by kiaunel
Tue Feb 23, 2016 4:55 pm
Forum: Beginner Basics
Topic: Use WAN IP on LAN
Replies: 2
Views: 606

Re: Use WAN IP on LAN

Hi! I'm using RB850Gx2 (powerpc) with 6.34.2 installed. There is no any specific configuration, just DHCP, some NAT rules for port forwarding and some reserved IP addresses by MAC address. What I want is allow use WAN IP addresses in LAN. For example - one NAS drive with IP address 10.0.0.39, I can...
by kiaunel
Mon Feb 22, 2016 10:00 pm
Forum: Beginner Basics
Topic: Bridge config for SXT Lite5 ac (having issues)
Replies: 4
Views: 2018

Weird indeed but loosing connectivity after link is established sounds like loop but may be something else

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Mon Feb 22, 2016 8:12 pm
Forum: Beginner Basics
Topic: Bridge config for SXT Lite5 ac (having issues)
Replies: 4
Views: 2018

Are you making a loop? With wlan1 on second sxt? Why are you using wlan1 anyway? Make sure wlan1 is not connecting to anything. Without seeing configs this was my first gues.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 10:40 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

Wait a minute... What IP get the switch? Is it public? If so I think you can not get second public IP from your isp.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 10:08 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

You can try to plug your laptop or computer to modem to see if you get an ip.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 8:44 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

Re: Initial setup hurdles

Look , i`ve pasted your config in a test device and it worked. I mean the eth6 got an ip [admin@MikroTik] > export # feb/21/2016 18:40:36 by RouterOS 6.34.1 # software id = # /interface bridge add admin-mac=E4:8D:8C:22:DD:F5 auto-mac=no name=bridge-local /interface ethernet set [ find default-name=e...
by kiaunel
Sun Feb 21, 2016 8:33 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

Re: Initial setup hurdles

[admin@MikroTik] > ip address print Flags: X - disabled, I - invalid, D - dynamic # ADDRESS NETWORK INTERFACE 0 ;;; default configuration 192.168.88.1/24 192.168.88.0 bridge-local 1 192.168.88.3/24 192.168.88.0 ether6-gateway [admin@MikroTik] > interface ethernet print Flags: X - disabled, R - runn...
by kiaunel
Sun Feb 21, 2016 8:01 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

If you add static IP to ether 6 it works?
ip add address=192.168.0.5/24 interface=ether6
Adapt your IP address and try to ping modem IP address. Hope i has not made any syntax error course I'm writing from my phone and don't have a mikrotik in front on me

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 7:54 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

in ether print
See the number of the interface
in ether mon number

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 7:48 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

Did u check the Ethernet link on 6?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 7:33 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

He has in config dhcp-client on ether6

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 7:21 pm
Forum: Beginner Basics
Topic: Initial setup hurdles - modem not recognized
Replies: 22
Views: 1402

Re: Initial setup hurdles

Check your cable if your modem light is still red i would take a look at interface status. From winbox go to interfaces and on status tab check your interface link. Maybe auto negociation has failed. Check the rate status.
by kiaunel
Sun Feb 21, 2016 2:23 pm
Forum: General
Topic: IPV6 internal configuration
Replies: 64
Views: 9293

None of your devices will use dhcp server so you can remove it.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 21, 2016 11:45 am
Forum: Beginner Basics
Topic: How does one setup hAP lite as a wireless client?
Replies: 2
Views: 3664

Re: How does one setup hAP lite as a wireless client?

The wireless mode you need id station-bridge and a bridge with wlan1 and master-interface of lan ports.If the dhcp-client is assigned to wlan interfave and not getting an ip it means your hap is not connected. Check this in wireless -- wlan1 -- status tab. There you should see if it is connected. If...
by kiaunel
Sun Feb 21, 2016 9:31 am
Forum: Beginner Basics
Topic: pptp routing
Replies: 7
Views: 706

Re: pptp routing

so you need to reach 192.168.3.0 subnet from 192.168.9.0
ip route add dst-address=192.168.3.0/24 gateway=pptp-out1 
by kiaunel
Sun Feb 21, 2016 9:10 am
Forum: Beginner Basics
Topic: pptp routing
Replies: 7
Views: 706

Re: pptp routing

If I run pptp with the "add default gw" option then yes all traffic is routed via pptp
Is what you wanted, right?
by kiaunel
Sun Feb 21, 2016 8:01 am
Forum: Beginner Basics
Topic: Basic setup of CCR-1009-8G-1S router
Replies: 2
Views: 525

Re: Basic setup of CCR-1009-8G-1S router

What did u do and not work?
by kiaunel
Sat Feb 20, 2016 10:29 pm
Forum: Beginner Basics
Topic: VLans on Firewall Filtering
Replies: 14
Views: 2486

Make your firewall rules with interfaces blocking... Like that... IP firewall filter add chain=forward in-interface vlanx out-interface=vlany action=drop I wrote the rule from mind as i'm on phone now so hope I have not make any sintax error. Adapt that rule to your config and you should be fine. Se...
by kiaunel
Sat Feb 20, 2016 5:58 pm
Forum: General
Topic: how creat vlan in rb1100 ?
Replies: 7
Views: 671

No. How do you want to send internet? Make a scheme of your network.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Feb 20, 2016 2:33 pm
Forum: General
Topic: how creat vlan in rb1100 ?
Replies: 7
Views: 671

Then make sure interfaces are not bridged, or have none in the master port settings, ad ips to interfaces, if you need dhcp on them create dhcp servers assigned to every interfaces, then create rules in firewall to block traffic between interfaces. No need for vlan from what you said. Vlan only need...
by kiaunel
Sat Feb 20, 2016 2:05 pm
Forum: General
Topic: Connecting to inside servers fails
Replies: 1
Views: 322

Re: Connecting to inside servers fails

I think you need Hairpin NAT :http://wiki.mikrotik.com/wiki/Hairpin_NAT
You need to nat your inside packets
/ip firewall nat
add chain=srcnat src-address=172.16.239.0/24 \
dst-address=172.16.239.7 protocol=tcp dst-port=80 \
out-interface=LAN action=masquerade
by kiaunel
Sat Feb 20, 2016 1:25 pm
Forum: Beginner Basics
Topic: pptp routing
Replies: 7
Views: 706

Re: pptp routing

When you connect to your client do you get default route? there must be an option like "route all traffic to vpn server". Check that it is active. Also did not understant what is realy your pptp subnet. is 9.0/24 or 3.0/24? Anyway... Both subnets must be in masquerade assuming one is your lan and on...
by kiaunel
Sat Feb 20, 2016 1:13 pm
Forum: General
Topic: how creat vlan in rb1100 ?
Replies: 7
Views: 671

Add vlan to master interface or to the bridge, depending of your config. You did not explained in detail what do you want

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 19, 2016 3:40 pm
Forum: Beginner Basics
Topic: MikroTik Graphing-Restrict LAN users from viewing!!!
Replies: 9
Views: 1025

Re: MikroTik Graphing-Restrict LAN users from viewing!!!

In this situation only option 1 is for you. But, there is a way also, : configure a vpn server on mikrotik, give vpn client an address space diferent from your users and allow only that subnet to view graphs. Thanks. I have changed the port number from ip--> services. Now i have to view the graphs ...
by kiaunel
Fri Feb 19, 2016 3:16 pm
Forum: Beginner Basics
Topic: MikroTik Graphing-Restrict LAN users from viewing!!!
Replies: 9
Views: 1025

Re: MikroTik Graphing-Restrict LAN users from viewing!!!

In this situation only option 1 is for you.
But, there is a way also, : configure a vpn server on mikrotik, give vpn client an address space diferent from your users and allow only that subnet to view graphs.
by kiaunel
Fri Feb 19, 2016 2:41 pm
Forum: Beginner Basics
Topic: MikroTik Graphing-Restrict LAN users from viewing!!!
Replies: 9
Views: 1025

Re: MikroTik Graphing-Restrict LAN users from viewing!!!

There are two options.
1. change www server port in ip--> services , from winbox
2. drop from firewall access subnet to ip of mikrotik on port 80 but allow your ip
by kiaunel
Fri Feb 19, 2016 11:38 am
Forum: Beginner Basics
Topic: Problem with Multiple DHCP
Replies: 1
Views: 382

Make sure ports are not included in any bridge and dhcp servers are allocated to the right port

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 19, 2016 11:15 am
Forum: Beginner Basics
Topic: How do I stop MAC address access to router from Winbox on guest vlan
Replies: 3
Views: 2634

Re: How do I stop MAC address access to router from Winbox on guest vlan

I think you block traffic in forward chain. When you access router in winbox the packets are in input chain, they are destinated for the router itself. Others, for others devices are passing the router , this means forward. This is for ip. About mac access i don`t know if you can realy block... mayb...
by kiaunel
Fri Feb 19, 2016 11:12 am
Forum: Beginner Basics
Topic: Extend wireless to lan with map lite?
Replies: 2
Views: 1368

Re: Extend wireless to lan with map lite?

Is your map in station mode on wireless tab? Then change to station bridge.
by kiaunel
Thu Feb 18, 2016 8:56 pm
Forum: Beginner Basics
Topic: RB2011UAS-2HnD-IN - switch + wifi AP
Replies: 2
Views: 651

Or, to avoid double nat make ADSL bridge, connect with mikrotik directly to internet and if you want guests in separate network make an virtual ap with an separate dhcp server and firewall to avoid guest subnet to talk with your subnet.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Feb 18, 2016 3:46 pm
Forum: Beginner Basics
Topic: extending network range
Replies: 31
Views: 6294

All depends of what do u need. More bandwidth... Go to ac. If not 951g or 2011 series arevery powerful device for home use.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Feb 18, 2016 2:52 pm
Forum: Beginner Basics
Topic: extending network range
Replies: 31
Views: 6294

Re: extending network range

Second device you can make it bridge so the only dhcp server will be on first, and you will have the same subnet in your LAN . Also set up same ssid with same encription on both but different channels, for roaming clients.
by kiaunel
Thu Feb 18, 2016 2:46 pm
Forum: Beginner Basics
Topic: Absolute beginner with an RB2011UiAS-2HnD-IN
Replies: 3
Views: 418

Re:

There are two independent switches in 2011 so it is not possible to enslave ether 6-10 to ether2. Didn`t know that, sorry. So i gues there is a switch for 10/100/1000 ports and one for 10/100. Anyway the setup is still the same i think. Wlan1 bridged with one master ports remains for the routed par...
by kiaunel
Thu Feb 18, 2016 12:49 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Re: MAP2N - using ethernet 2 for internet input

This was a very basic config so you can start . a- you can forget about it it was from a test ... don`t input that line b- pool1 is the ip range dhcp-server will assign to clients, dhcp1 is the server itself. c- yes you should... like i said this was a very basic config to make things work as u want...
by kiaunel
Thu Feb 18, 2016 12:34 pm
Forum: Beginner Basics
Topic: Absolute beginner with an RB2011UiAS-2HnD-IN
Replies: 3
Views: 418

Re: Absolute beginner with an RB2011UiAS-2HnD-IN

The easiest way is to set up mikrotik as a simple router at the begining . Then you will have a bridge between ether2 and wlan1. Ports from ether3-10 will be with master interface ether2. Remove ether2 from bridge so the routing will be from ether1 to wlan1 and other ports like 2-10 will act as a sw...
by kiaunel
Wed Feb 17, 2016 8:09 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Re: MAP2N - using ethernet 2 for internet input

Ok, this is the config for you" /interface wireless set [ find default-name=wlan1 ] disabled=no mode=ap-bridge wireless-protocol=802.11 /interface bridge add admin-mac=00:11:22:33:44:55 auto-mac=no name=bridge1 /ip pool add name=dhcp ranges=192.168.88.3-192.168.88.30 add name=dhcp_pool1 ranges=192.1...
by kiaunel
Wed Feb 17, 2016 3:49 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Re: MAP2N - using ethernet 2 for internet input

It has nothing to do with mac on wan interface it is configurable on any ther by ip and default route. On what settings is rebooting or not allow you to access it? Keep in mind there are situations when deleting bridges or move ip from one interface to other when the device will not be accesible by ...
by kiaunel
Tue Feb 16, 2016 7:33 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Re: MAP2N - using ethernet 2 for internet input

Ok it`s very easy. In the ip tab on address double click on 192.168.88.1 and put on interface bridge1 or whatever your bridge name is . Like you said *IP address 192.168.88.1/24 is set on LAN port instead of lan port use bridge . Same thing in ip---dhcpd server -- double click on server1 and change ...
by kiaunel
Tue Feb 16, 2016 4:39 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

I'm on phone now and can not make an elaborate post. Later I will.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Tue Feb 16, 2016 2:20 pm
Forum: Beginner Basics
Topic: interface bandwith limit
Replies: 5
Views: 593

Re: interface bandwith limit

input as 30M don`t think will work.... instead use 30000
by kiaunel
Tue Feb 16, 2016 2:02 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Re: MAP2N - using ethernet 2 for internet input

Ok, now i think i understand. your wan port is ether1. Remove ether2 from bridge and for make ether2 wan move dhcp-client on ether2 that way you will get default route on ether2 and you need to make nat settings considering your out-interface will ne ether2. But, this wil be a router after router se...
by kiaunel
Tue Feb 16, 2016 11:34 am
Forum: Beginner Basics
Topic: LED on/off RB951G-2HnD
Replies: 20
Views: 2906

Re: LED on/off RB951G-2HnD

One led can only take one activity.... if you want to assing other activity to led1 delete default one and create other
by kiaunel
Tue Feb 16, 2016 11:06 am
Forum: General
Topic: Crazy issue: Router stops responding [seemingly at random]
Replies: 2
Views: 386

Re: Crazy issue: Router stops responding [seemingly at random]

Sounds like you have a loop in your network
by kiaunel
Tue Feb 16, 2016 10:41 am
Forum: Beginner Basics
Topic: LED on/off RB951G-2HnD
Replies: 20
Views: 2906

Re: LED on/off RB951G-2HnD

Yes, I know, but there is no Led1, Led2.... in LEDs
Not every routerboard have access to configure all leds. some have leds 1-5 + user led like mine 433 and others like 750 or hap lite has access only to user led
by kiaunel
Mon Feb 15, 2016 10:55 pm
Forum: Beginner Basics
Topic: LED on/off RB951G-2HnD
Replies: 20
Views: 2906

In winbox go to system -> LEDs. You can setup them there

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Mon Feb 15, 2016 10:30 pm
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

Re: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.

please be more specific... why is not working? syntax? or do not block your traffic? Make sure you inserted rule before forward accept all
for logging
sys logging add topics=wireless action=memory
by kiaunel
Mon Feb 15, 2016 10:21 pm
Forum: Beginner Basics
Topic: Implementing vlan in Different Ways
Replies: 5
Views: 668

Re: Implementing vlan in Different Ways

never made an setup like this but i think in first situation ether1 ans wlan are in trunk and traffic will be tagged and in second wil be an access port and traffic wil be untagged. Hope i`m not wrong. My setup is like this... Vlan 100 and 200 added to ether2 and ether 3 slave to ether2. This are tw...
by kiaunel
Mon Feb 15, 2016 10:14 pm
Forum: Beginner Basics
Topic: Dhcp on VLans [SOLVED]
Replies: 5
Views: 11430

Re: Dhcp on VLans [SOLVED]

ZeroByte is right you don`t need bridge or vlan0 on ether2. Just use ether2. Now for the trunk port in the other end is trunk configured?
by kiaunel
Mon Feb 15, 2016 10:06 pm
Forum: Beginner Basics
Topic: DNS - Ubuntu Bind Port Forwarding
Replies: 1
Views: 659

Re: DNS - Ubuntu Bind Port Forwarding

Move firewall rule to ccr02 becouse your clients request are not passing to your wan but from your clients lan to wan of ccr02 and to dns server
by kiaunel
Mon Feb 15, 2016 9:01 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Re: IP Camera Port forwarding

you`re welcome... anytime.
by kiaunel
Mon Feb 15, 2016 8:15 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

First of all is your map router or bridge? If it is router is normal to connect only from eher1 with default setup. Second... If u bridge wlan and ether 2 your map is a simple access point and ignore ether1. Now.... If only one device can connect this way change wireless mode on ubnt. I bet is stati...
by kiaunel
Mon Feb 15, 2016 6:07 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

What did u do?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Mon Feb 15, 2016 4:08 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Why don't connect cameras after mikrotik? That way it will be much easier If you can not do this remove dstnat from ADSL router and make sure land and wireless on DSL are bridged because you should have replys from camera on ping and move dstnat rules on Microtik. When you try to reach camera from o...
by kiaunel
Mon Feb 15, 2016 6:34 am
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Where is located the other router( non mikrotik)? Make a simple network diagram so I can understand your setup I mean how cameras reach mikrotik? I see you have 192.168.5.0/24 on eth1 eth1 is not wan port? ppoe is not connected to eth1? can u ping camera ip from mikrotik? Sent from my Lenovo K50-t5 ...
by kiaunel
Mon Feb 15, 2016 6:05 am
Forum: Wireless Networking
Topic: Cannot acces main network from second Access Point
Replies: 6
Views: 789

Re: Cannot acces main network from second Access Point

:)) is a tplink afterall....
by kiaunel
Sun Feb 14, 2016 11:13 pm
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

No idea but if you can connect with cable try to log wireless and dhcp maybe you will see what is happening.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 10:49 pm
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

What problems?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 9:31 pm
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

No it will not block internet connection. It will only block request coming from wireless interface to modem who want to connect to modem IP on port 80 witch is the management interface of the modem

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 5:50 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Yes you will access camera like this http://mikrotik.host:cameraport

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 5:10 pm
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

OK then block incoming connection from wlan to modem IP DST port 80 adapt this rule for you ip firewall filter add chain=forward protocol=tcp dst-port=80 dst-address=xxx.xxx.xxx.xxx in-interface=wlan1 out-interface=ether1-gateway action=drop you can use on dst-address=!youripaddress to block all sub...
by kiaunel
Sun Feb 14, 2016 5:00 pm
Forum: Beginner Basics
Topic: Flash Support?
Replies: 3
Views: 486

There is a x86 version to install on pc
http://www.mikrotik.com/download

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 4:12 pm
Forum: Beginner Basics
Topic: Flash Support?
Replies: 3
Views: 486

Re: Flash Support?

Yes, U model have support for usb storage
by kiaunel
Sun Feb 14, 2016 4:09 pm
Forum: Wireless Networking
Topic: Wireless and bridging
Replies: 8
Views: 1500

Re: Wireless and bridging

station can not work in bridge mode.
try station bridge or station wds
by kiaunel
Sun Feb 14, 2016 4:03 pm
Forum: Beginner Basics
Topic: help me pls
Replies: 8
Views: 843

Re: help me pls

this time i already can connect to inet from my mikrotik So you can ping from microtik to internet right? my question is how i can connect to inet from my modem adsl....?? help pls I don`t understant what means from "modem adsl"? Don`t u try connect to internet from a computer connected to mikrotik...
by kiaunel
Sun Feb 14, 2016 3:56 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Re: IP Camera Port forwarding

to use noip.com you have to use a custom script. Better use buildin dyndns : [admin@Gateway] > ip cloud set ddns-enabled=yes [admin@Gateway] > ip cloud print ddns-enabled: yes update-time: yes public-address: 89.137.xx.xx dns-name: 268xxxxxxxxxx.sn.mynetname.net status: updated [admin@Gateway] > It ...
by kiaunel
Sun Feb 14, 2016 3:38 pm
Forum: Wireless Networking
Topic: Cannot acces main network from second Access Point
Replies: 6
Views: 789

And disable dhcp server on tplink so it will be a wireless switch

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 3:24 pm
Forum: Beginner Basics
Topic: help me pls
Replies: 8
Views: 843

Re: help me pls

Was realy hard to understant what do you want to do. Why do you have on ether1 ether4 and wlan1 an ip from the same subnet as your modem. What is 5.0/24 netmask anyway.... modem subnet? if so 5.1 is not your modem ip? how do you connect to modem? dhcp? static ip? I think you should start over and co...
by kiaunel
Sun Feb 14, 2016 3:09 pm
Forum: Beginner Basics
Topic: LED on/off RB951G-2HnD
Replies: 20
Views: 2906

Re: LED on/off RB951G-2HnD

sys leds add type=interface-activity interface=wlan1 leds=user-led And the user led will blink when thereis wireless traffic on wlan1 You can set many options instead of interface-activity [admin@Gateway] > sys leds add type= Type ::= ap-cap | flash-access | interface-activity | interface-receive | ...
by kiaunel
Sun Feb 14, 2016 2:54 pm
Forum: Beginner Basics
Topic: IP Camera Port forwarding
Replies: 25
Views: 22022

Re: IP Camera Port forwarding

chain=dstnat action=dst-nat to-addresses=10.10.2.105 to-ports=8800 protocol=tcp in-interface=wan dst-port=8800 log=no log-prefix=""
Also make sure camera have internet access, i mean to set gateway on camera... this is a common mistake, not to set gateway on ip camera
by kiaunel
Sun Feb 14, 2016 7:17 am
Forum: Wireless Networking
Topic: Guest Wi-Fi on seperate Access Point hardware
Replies: 11
Views: 2747

Re: Guest Wi-Fi on seperate Access Point hardware

Oh, my bad. Then forget about trunk and set access port coonected to ap with vlan 200 . And on ap there is nothing to do.
by kiaunel
Sun Feb 14, 2016 7:00 am
Forum: Beginner Basics
Topic: Restricting access to router before MikroTik, and WiFi not working as it should... help needed.
Replies: 14
Views: 1038

Why don't you make modem in bridge and have the ISP connection on mikrotik? Or how the clients can access the DSL? It has not a password? You can d add a drop forward rule with source hotspot subnet destination gateway proto TCP dstport 80 if 80 is the port of web management interface of DSL. Sent f...
by kiaunel
Sun Feb 14, 2016 6:54 am
Forum: RouterBOARD hardware
Topic: How to reduce txpower on a RB912UAG-5HPnD ?
Replies: 11
Views: 1854

The moon has nothing to do with your network. Just try the solution czolo gave to you. To better understand it when you set antenna gain ros thinks you have a more powerful antenna and decrease the power on the wireless chip to maintain country regulations. But you will have the same antenna and wit...
by kiaunel
Sun Feb 14, 2016 6:48 am
Forum: General
Topic: Retrieving WPA2 key
Replies: 3
Views: 604

In winbox click on settings and remove passwords

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sun Feb 14, 2016 6:36 am
Forum: Wireless Networking
Topic: Guest Wi-Fi on seperate Access Point hardware
Replies: 11
Views: 2747

Re: Guest Wi-Fi on seperate Access Point hardware

You can not make the guest subnet reach internet without srcnat or masquerade. The setup will be like this : 1. Create two vlans on router assigned to the interface connected to ap This will be a trunk port.. For example vlan 100 will be your vlan and vlan 200 will be guest vlan.Make a dhcp server f...
by kiaunel
Fri Feb 12, 2016 9:55 pm
Forum: Beginner Basics
Topic: Help setting up my private/public network
Replies: 12
Views: 2067

Virtual ap can have different ssid from main. I don't know if roaming works between 2.4 and 5

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 12, 2016 8:38 pm
Forum: Beginner Basics
Topic: MAP2N - using ethernet 2 for internet input
Replies: 19
Views: 3257

Set on ether2 master interface ether1

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 12, 2016 9:20 am
Forum: Beginner Basics
Topic: Export configuration to another diferent device
Replies: 2
Views: 342

I just tried... Worked.... somehow
But ETH interfaces were switched... I mean plunged cable in ether1 but in ros the link came up to ether3 I think because the two wireless interfaces from 433 are missing in 750g.
Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Feb 12, 2016 6:54 am
Forum: Beginner Basics
Topic: Export configuration to another diferent device
Replies: 2
Views: 342

Export configuration to another diferent device

Hello,
I think I already know the answer but if I try to export the whole config from a 433ah to a 750g it will work?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Wed Feb 10, 2016 1:47 pm
Forum: Beginner Basics
Topic: How to instal router 950 G with v6.8
Replies: 4
Views: 732

Why do you want to use netinstall? The router is not booting?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Tue Feb 09, 2016 4:07 pm
Forum: Beginner Basics
Topic: required help to create DHCP for 1000 users
Replies: 4
Views: 3651

Yes

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Tue Feb 09, 2016 1:32 am
Forum: Beginner Basics
Topic: problem: authorization login page opening always when user connect to network
Replies: 10
Views: 775

Like as @Zerobyte said... As long the cookie is valid user get no login screen. Tested in my config also. Make sure cookie validity time is set equal to user authorization time.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Feb 06, 2016 11:31 pm
Forum: Wireless Networking
Topic: Wireless and bridging
Replies: 8
Views: 1500

Post your config here

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Sat Feb 06, 2016 1:58 pm
Forum: General
Topic: Feature request: Free packages / version selection for install
Replies: 2
Views: 288

+1

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Feb 04, 2016 11:56 pm
Forum: General
Topic: How can Drop - sharing internet program
Replies: 18
Views: 2314

Try to limit connections or packets. For sure you can see a difference between a normal client and those who sharing. This will not stop them to share but for sure will make them problems :) . Some years ago I was changing the TTL to 1 and luckily they did not know to increment it again . Sent from ...
by kiaunel
Thu Feb 04, 2016 9:16 pm
Forum: Beginner Basics
Topic: Hotspot Help
Replies: 7
Views: 1274

Set your plex server ip în the same subnet as your clients network. Then set eher2 as a slave to ether3.

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Feb 04, 2016 5:13 pm
Forum: Wireless Networking
Topic: Wireless and bridging
Replies: 8
Views: 1500

Do you connect to ap? If you put an dhcp client on wireless interface are u getting an ip? Then can you ping from mikrotik? If you can then simply add a bridge interface with wireless interface and one or more ethX. It should work. Before the bridge remove dhcp client. Sent from my Lenovo K50-t5 usi...
by kiaunel
Tue Feb 02, 2016 8:38 pm
Forum: Beginner Basics
Topic: Openvpn behind Mikrotik
Replies: 1
Views: 323

Somehow your packets from vpn server are passing to mikrotik who block them... Try allowing that packets source ip to their destination. Without your network topology there is not too much help you can get

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Jan 29, 2016 8:42 pm
Forum: Announcements
Topic: v6.34 [current] is released!
Replies: 91
Views: 23282

Re: v6.34 [current] is released!

Have attempted an update on two mibsbe devices, an RB450G and RB2011UAS-RM, both are now broken. Haven't been able to revert or recover them yet. Any one else have troubles? Had problems with wireless part mine was not dead. Try netinstall... It worked for me Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Jan 29, 2016 8:03 pm
Forum: General
Topic: RouterOS ~ Multiple Trunks
Replies: 2
Views: 376

Move port 6,7,8 to bridge vlan trunk as u did with port 9

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Fri Jan 29, 2016 9:01 am
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

Re: Wireless package missing....

Hmm, ok i`m used to be on the latest release... i can`t say i have any problems with 6.32.3.
Thanks for your support, anyway...
by kiaunel
Thu Jan 28, 2016 7:57 pm
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

Installed 6.32.3 from netinstall and wireless is working now. I've unistalled wireless and installed wireless-cm2 ans wireless still working but now i can not update to 6.33.5. It download files just fine reboot but no upgrade is done... The files still prezent în files tab. Sent from my Lenovo K50-...
by kiaunel
Thu Jan 28, 2016 5:06 pm
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

How can i manually install a package?

Sent from my Lenovo K50-t5 using Tapatalk
by kiaunel
Thu Jan 28, 2016 2:18 pm
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

Re: Wireless package missing....

Not even if i try to upgrade the wireless packages are not downloaded. See the screenshot :
2016-01-28 (1).png
by kiaunel
Thu Jan 28, 2016 2:09 pm
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

Re: Wireless package missing....

I can not enable wireless package becouse is missing from list.
It was uploaded to files tab but after reboot was not installed.
by kiaunel
Thu Jan 28, 2016 11:27 am
Forum: Wireless Networking
Topic: Wireless package missing....
Replies: 9
Views: 1979

Wireless package missing....

Hello, I have an old RB 433ah as home router. Yesterday when i tried to upgrade to 6.33.5 it was an error as wireless package is missing ... After this i tried to downgrade to 6.32.3 as i sow on forums this was the last version suppored to mipsbe arhitecture. Forums information is confusing... Is th...
by kiaunel
Wed Jan 27, 2016 2:09 pm
Forum: General
Topic: OpenVPN Server error: TLS failed
Replies: 43
Views: 78457

Re: OpenVPN Server error: TLS failed

changed the config and now it connect succesful.
now how to push default route?
by kiaunel
Wed Jan 27, 2016 10:36 am
Forum: General
Topic: OpenVPN Server error: TLS failed
Replies: 43
Views: 78457

Re: OpenVPN Server error: TLS failed

thank you for your reply. Indeed the was worng placed certificate myca intread of server. What i tried to do is create new certifiicates , with the name and common name my host name uploaded to client configuration and indeed the errors changes. Now my server certificate name is kiaunel.fiberdatatel...
by kiaunel
Mon Jan 25, 2016 6:38 am
Forum: General
Topic: OpenVPN Server error: TLS failed
Replies: 43
Views: 78457

Re: OpenVPN Server error: TLS failed

Thanks for your quick reply , but i don`t understand how i have to create my certs. I`ve crated with the lines in this topic" /certificate add name=ca-template common-name=myCa key-usage=key-cert-sign,crl-sign add name=server-template common-name=server add name=client1-template common-name=client1 ...
by kiaunel
Sun Jan 24, 2016 8:30 pm
Forum: General
Topic: OpenVPN Server error: TLS failed
Replies: 43
Views: 78457

Re: OpenVPN Server error: TLS failed

Hello, I try to set up an openvpn server on microtik and after i fallowed all in this topic i get tls error. I will post my configs and logs maybe someone can point me where i`m wrong. Microtik Log : 20:20:38 ovpn,debug,error,20076,29312,60348,61328,27884,20684,58064,60344,l2tp,info,60348,debug,79,6...
by kiaunel
Thu Apr 16, 2015 10:28 pm
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

Re: ipv6 don`t work with pptp?

Interface 54: VPN Home Internet Address Physical Address Type -------------------------------------------- ----------------- ----------- 2001:470:20c7::3 Permanent fe80::f Permanent ff02::1 Permanent ff02::2 Permanent ff02::c Permanent ff02::16 Permanent ff02::fb Permanent ff02::1:2 Permanent ff02::...
by kiaunel
Thu Apr 16, 2015 9:32 pm
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

Re: ipv6 don`t work with pptp?

i think yes I can not understand why the pptp interface is treated diferent than lan ... in lan i have a fully working SLAAC ipv6 dual stack. Also i did not manage to make dhcpd6 server work by asingning DUID for clients .. i get wrong duid ... but this is another problem.. for now i just would like...
by kiaunel
Thu Apr 16, 2015 8:02 pm
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

Re: ipv6 don`t work with pptp?

C:\Windows\system32>ping ff02::1%59 Pinging ff02::1%59 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for ff02::1%59: Packets: Sent = 2, Received = 0, Lost = 2 (100% loss), Control-C ^C C:\Windows\system32> C:\Windows\system32>p...
by kiaunel
Thu Apr 16, 2015 7:22 pm
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

Re: ipv6 don`t work with pptp?

Here is my ipv6 config maybe helps.... /ipv6 dhcp-server add address-pool=ipv6-pool disabled=no interface=lanbridge name=server1 /ipv6 pool add name=ipv6-pool prefix=2001:470:20c7::/48 prefix-length=64 /ipv6 address add address=2001:470:1f1a:233::2 comment="ip 6 extern" interface=sit1 add address=20...
by kiaunel
Thu Apr 16, 2015 7:15 pm
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

Re: ipv6 don`t work with pptp?

Hi,
I`m using /64 prefix with SLAAC both for non pptp clients and for pptp. It seems to not forwarding ipv6 packets becouse i cand not ping any ipv6 address and not the gateway. Routing has nothing to do with ping some address in the same /64 subnet
by kiaunel
Thu Apr 16, 2015 2:53 pm
Forum: General
Topic: Accessing Clients throw DHCP router
Replies: 3
Views: 876

What kind of reaching do you want? Port forward on routers behind microtik if i understand corectly
by kiaunel
Thu Apr 16, 2015 11:03 am
Forum: General
Topic: ipv6 don`t work with pptp?
Replies: 9
Views: 1754

ipv6 don`t work with pptp?

Hello, I have a rb 433 ah with ros 6.27. I managed to setup a tunnel for ipv6 and my clients get ipv6 conectivity. But pptp clients get only ipv6 address but link local default route in windows. What can be wrong? PPP adapter VPN Home: Connection-specific DNS Suffix . : Description . . . . . . . . ....
by kiaunel
Thu Jul 24, 2014 11:57 pm
Forum: RouterBOARD hardware
Topic: dead Sxt lite5?
Replies: 15
Views: 5724

Re: dead Sxt lite5?

Try change the power suply
by kiaunel
Thu Jul 24, 2014 7:27 am
Forum: RouterBOARD hardware
Topic: RB433 Ethernet 2
Replies: 1
Views: 559

Re: RB433 Ethernet 2

Assuming that you tried with a good cable working on ether3 and not working to ether2 and the problem is not on the other end of ther cable (a bad switch or network card) try this : interface ethernet set 1 auto-negotiation=no full-duplex=no speed=10Mbps If with this yoiu gor a link then you have a ...
by kiaunel
Thu Jul 24, 2014 7:19 am
Forum: RouterBOARD hardware
Topic: dead Sxt lite5?
Replies: 15
Views: 5724

Re: dead Sxt lite5?

Hello, this is almost the same situation as in my case. I have got an 411GL sometimes working 5 days, once just 2 minutes and then dead. Then i need to plugged off and back. So far i do not know what the problem is. I think this is not ROS problem.I am using 6.17 with 3.18 routerboot. I tried diffe...
by kiaunel
Tue Jul 22, 2014 4:49 pm
Forum: RouterBOARD hardware
Topic: dead Sxt lite5?
Replies: 15
Views: 5724

Re: dead Sxt lite5?

When you get it to boot with the button, you can upgrade RouterBOOT version (/system routerboard upgrade), as it looks like the problem lies there. Let us know if you succeed they are both funtional now but the problem was that they only booted with reset button pressed, the i upgrade firmware , re...
by kiaunel
Tue Jul 22, 2014 4:46 pm
Forum: RouterBOARD hardware
Topic: dead Sxt lite5?
Replies: 15
Views: 5724

Re: dead Sxt lite5?

bad Power supply? cable? rj-45 jacks?
did you tested them?
when i replaced the first one i`ve installed a new one with new power suply
by kiaunel
Mon Jul 21, 2014 8:09 pm
Forum: RouterBOARD hardware
Topic: dead Sxt lite5?
Replies: 15
Views: 5724

dead Sxt lite5?

Hello, i have a strange situation : i`ve installed two weeks ago a wireless link to one of my clients and after 3 day the sxt on client side was dead : no lan link no wireless response, no beep on boot. I changed then with another SXT lite 5 and after 5 days the same... no lan link no beep no wirele...