Community discussions

MikroTik App

Search found 8 matches

by zabullet
Sat Nov 22, 2014 8:39 pm
Forum: General
Topic: graphs deleted after reboot on v.5.0 / slow NTP sync
Replies: 52
Views: 16260

Re: graphs deleted after reboot on v.5.0 / slow NTP sync

I still get this behaviour on 6.22.
by zabullet
Sun Jul 27, 2014 11:02 pm
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

Re: HELP: VLANs on WLAN

Sigh! This is a very humbling experience.....still no luck!

Anyone want to spot what idiotic thing I'm getting wrong?

Regards,

zb
by zabullet
Sat Jul 26, 2014 7:03 pm
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

Re: HELP: VLANs on WLAN

Several more hours and I'm pretty sure I'm getting closer.... I simplified my AP config to the following /interface wireless set 0 disabled=no mode=ap-bridge mtu=1600 channel-width=20/40mhz-ht-above bridge-mode=enabled band=2ghz-b/g/n wireless-protocol=any /interface wireless add area="" master-inte...
by zabullet
Fri Jul 25, 2014 11:16 am
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

Re: HELP: VLANs on WLAN

:( Nope. I've checked all the values for the MTUs are *all* > 1500 *and* VLANs match, but still not working. Conceptually I think I understand what I need to do to get it working, so I'll tinker this weekend and probably simplify the setup. If I don't get it working I'll post some more config. Regar...
by zabullet
Thu Jul 24, 2014 11:46 pm
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

Re: HELP: VLANs on WLAN

Still not working, but feel I'm getting closer. Thanks. 1. I set VLAN on my eth of my laptop and plugged into RB951 and I got the expected behaviour. i.e. it worked 2. I checked the hosts on the RB951 and MAC for the RB750 can only be seen on eth1/bridge1, which suggests an MTU issue (not sure how t...
by zabullet
Wed Jul 23, 2014 7:44 pm
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

Re: HELP: VLANs on WLAN

:( You are correct on your assumption that ether1 of RB951 is connected to the RB750GL....still no dice! By default the wlan1 is disabled if you factory reset with no config, so in the end I ran the following. /interface wireless set 0 adaptive-noise-immunity=none allow-sharedkey=no antenna-gain=0 a...
by zabullet
Tue Jul 22, 2014 11:09 pm
Forum: Wireless Networking
Topic: HELP: VLANs on WLAN
Replies: 8
Views: 1909

HELP: VLANs on WLAN

Hi Guys, I'm really struggling with completing my network setup. I have the following *working* setup ADSL Modem <-PPPoE-> Router (RB750GL) <-> Ubiquiti AP On the Router I have 2 VLANs 3 DHCP pools + servers /interface vlan add interface=ether2-master-local l2mtu=1594 name=vlan_100_25Low vlan-id=100...