Hi, I have followed this article: https://www.watchguard.com/help/docs/help-center/en-US/Content/Integration-Guides/General/Mikrotik%20VPN_firebox.html however regardless of whatever settings I try, on Mikrotik side I get PH2 State : no phase 2 and on Watchguard side: I get no response for IKE_SA_IN...

Hi,

I would like to think that I have solid understanding of VLANs. I have managed to get this working in a different way using Mikrotik.

Settings on my Cisco switch are fine and everything flows as it should tagged or tagless. Its purely from the management side I was having issue.

I am not using VLAN1 and I know its a default vlan on most devices.

As an example in WG, its pretty simple to configure an interface to pass traffic for tagged vlans and the also tell it to allow Untagged traffic for one particular vlan which is what I am trying to achieve here.

I meant "lose" or "lost" connection if that helps. I suppose the easiest way to put this would be, If I were to plug a device straight into bridge port on Mikrotik, I expect it to get an IP from native vlan 9 if that is set correctly. At the moment this isn't working when I set i...

So I have a RB2011iL fairly standard setup I have a cisco switch sitting behind it VLANs as below: VLAN ID = 9 management VLAD 1D = 10 Business PCs My trunk port on Cisco switch works fine when I leave it on native vlan as 1 however I want to set this as vlan 9 native When I change native VLAN 9 on ...

thanks for the input guys. @Sindy Am I correct in understanding your solution as below: Create a Bridge lets say AllLANs and add may be 4 ports to it. I then allow VLANs to that bridge. On the switch(es) side, I have a TAG port for VLANs traffic and then a TAGLESS port for LAN traffic 1 x cable each...

Hi, I wonder if someone can help me. I have following scenario 2 Bridges Mgmt Bridge contains port 2,3,4 VLANS Bridge contains port 7,8,9 I have a LAN with IP 192.168.155.1/24 and DHCP server runs on it and assigned to Mgmt Bridge - WORKS OK THROUGH ALL PORTS ON THE ROUTER I have 2 x VLANS with IPS ...

Thanks, I will give it another look

bump can someone advise
thanks

Hi Guys, I am having a strange issue. I have 2 identical Mikrotiks 3011. Router ONE I have 2 WAN interface (Port 1 used ) and working okay This router is a PPTP Server) Router TWO I have 3 WAN interfaces configured and used I have setup PPTP client I can see VPN gets connected I can ping all IPs fro...

hi sorry, unable to see the screenshot?

To help others .17 was providers device and has /28 on it.its in modem mode so passes all config to mikrotik which is configured to handle everything. I also have an fttc on wan2 to fail over to when wan1 is down.I am considering a load balancing setup in the future.if anyone is in same situation th...

Hi sorry for a late reply. I got it working after rebooting the router post proxy addition on wan interface.thanks.

Sent from my SUPER using Tapatalk

You just posted a question where you need to setup SRC and dst mating correctly.if you post up your static range I can help you setup corrdct translations.

Sent from my SUPER using Tapatalk

thanks for such a quick reply to give you full picture, this is what I have done to 62.30.5.16/28 range I have chucked it into 62.30.5.18/30 and named is WAN1 Router then I have chucked the rest as below 62.30.5.19/28 62.30.5.20/28 - - to 62.30.5.30/28 and added them as addresses on WAN1. Have I don...

Hi Guys, Apologies, if its a very direct approach however being self trained on Mikrotik and taking over a mess from predecessors' doesn't help. I have a following situation. Router: RB3011 UiAS-RM I am in need to set this up. It also has a local LAN for test i have created. it is 192.168.77.0/24 IS...

all sorted, not to worry

its all right.
I got it working.
I was configuring default route wrong

or If I rephrase the question. Do I need to assign VRRP to WAN or LAN interface?

tried that, doesn't give answers to my specific question about what IPs to assign on what interfaces

Hi, Wonder someone can clarify some things for me. I am wanting to setup a H/W failure between 2 Mikrotik. My setup is as below: Mikrotik 1 DHCP enabled Port 5: LAN : Range 192.168.41.15 - 192.168.41.30 IP: 192.168.41.1/24 Port1 - WAN >>> This goes to a switch which is connected to a gateway for int...

hello evince,
many thanks.

If I plug the cable from router into Port1, it automatically adds the route of 192.168.0.4/24 to it.
I have tried with route of 192.168.0.1 and it doesn't work.

Also, correct me if I am wrong, I have the following IP address assigned to Port2
192.168.0.0/24

thanks

anyone ??

Hi, Wonder if someone can check this for me. I have very basic setup. I have 2 internet lines coming into the office Port 1 >>> Main Internet Port 2 >>> ADSL As it stands, I am wanting to get ADSL working on Port WAN2 of Mikrotik RB2011 iL iN model and I am failing The cable from ADSL when I put it ...

at least, I am not alone going mad. I have already replaced one with a brand new similar model thinking it was hardware but it isn't. My router is now hanging up randomly so it can be hours or minutes before it goes down again. Has any one been able to find a solution. I inherited this setup from my...

Hi, This is my second post so please bare with me. We have a DC and we use the above. We are seeing the router just stop servicing completely and the only way to get it back up and running is to power cycle it. As it is on a remote location, so i am wanting to run some troubleshooting to find out th...

checked those, enabled / disable, no difference.

I am scratching my head on this one. It is something very foolish but I can't work it out. We have a virgin 100 Meg line which then goes into a Draytek and then into Mikrotek. If I plug straight into Draytek or Virgin (both have fixed IPs), I am getting full 100 Meg but the moment I am going through...

cheers. that got sorted long ago.

looks like I have got it working somehow.

Hi I wonder if I can get some advice please. I am familiar with mikrotiks but having a nightmare. I have recently moved a datacentre to another one and the servers in questions are hyper-v replica servers. I have managed to get them on the internet and dns records are pointed to the right IP. I have...