Can anyone confirm if these devices are safe to use outside at this date? It's such a weird design to have to point a device upwards to prevent water ingress. I live in Ireland and was thinking about buying these products, not sure if these devices would last long with the rain we get over here.
Hey guys, I have an LtAP device and having issues sending the longitude readings to a webserver, I can send the Latitude readings. If I use /tool fetch http-method=post http-header-field="Content-Type:application/json" http-data="{\"lat\":\"$lat\",\"lon\"...
Had the same issue today, sector went down last night and I drove to site with replacement wireless card but found that the gesp had water ingress and corrosion had set in on the pins. The grommet seems to trap the water once it gets in, this is not good as I have quiet a few of these in operation. ...
/interface vlan add comment="VLAN 1 - CCTV" interface=Trunk name=_CCTV vlan-id=1 add comment="VLAN 88 - PPoE" interface=Trunk name=_PPoE vlan-id=88 ether5 is named interface=Trunk and on ether2 is ppoe what port is ether2 been used for? it's named ppoe /interface pppoe-server ser...
Ok, you have your pppoe server set on a vlan and its set on interface Trunk which is ether5 from what I can see in your config. /interface vlan add comment="VLAN 88 - PPoE" interface=Trunk name=_PPoE vlan-id=88 Can you remove this /ip address add address=192.168.88.1/24 comment="PPoE ...
Have you tried removing the IP address set on the pppoe server? you dont need to have an address set for the pppoe interface just a ip pool for clients
What is Eero? :shock: mesh WiFi https://eero.com/ I have 2 in bridge mode. Excellent wireless coverage. I did order Audience to give it a try. Eero is what the guy who has NO BUSINESS AT ALL TOUCHING A NETWORK, is bringing into a commercial install. Sparky, "I use this all the time." Me, ...
It's possible that the antenna gain has changed on the radio to contry regulations reducing the power causing the signal to change. Did you upgrade both radios or just one?
6.46beta16 installed on hap mini (smips) using PEAR2\Net\RouterOS; api no longer works to login. PEAR2\Net\RouterOS\DataFlowException: Invalid username or password supplied. in /var/www/html/PEAR2/Net/RouterOS/Client.php:175 Stack trace: #0 /var/www/html/index.php(71):PEAR2\Net\RouterOS\Client->__co...
Set PPPOE to WAN interface and ether1 to LAN if it's an SXT device you are using /ip firewall address-list add address=0.0.0.0/8 comment=RFC6890 list=not_in_internet add address=172.16.0.0/12 comment=RFC6890 list=not_in_internet add address=192.168.0.0/16 comment=RFC6890 list=not_in_internet add add...
Have you tried removing the src-address=102.177.16X.X from /radius
add address=102.177.160.3 secret=XXXXXXXXXXXX service=ppp,login src-address=102.177.16X.X
Why don't you put routers at the towers and terminate the pppoe connections on the tower that the clients are connected to?
Are the VPLS tunnels back to the core with one PPPoE server and all your clients are terminating at the core?
Are you using the dns provided by the sim? try add 8.8.8.8 and 8.8.4.4 as the dns servers
You can remove the LTE dns from the LTE APNs menu untick Use Peer DNS and default route distance to 1
When you say "Access Mikrotik Router Externally" do you mean access from devices that are connected to the modem or from anywhere in the world? I use below rules on my Tik device along with port knocking and VPN In terminal copy paste below, It disables services except for winbox and www /...
You should just email or text the client and tell her that the internet will end on such a date unless payment is received and reconnection fee will incurr if payment is not made nake the text look automatic and robotic like
Open Terminal on router and paste firewall rules below /ip firewall address-list add list=Nextiva address=208.73.144.0/21 comment="Nextiva IP Range 208.73.144.0/21" /ip firewall address-list add list=Nextiva address=208.89.108.0/22 comment="Nextiva IP Range 208.89.108.0/22" /ip f...
You must be suffering from some kind of mac spoofing, if the clients are connecting to the hotspot from AP's, turn off default forward on the AP's If you try connect to the hotspot using your device and see if you can ping other devices connected to the hotspot, if you can ping the devices you will ...
When did this start to happen?
How are your clients connecting to the hotspot? wireless / wired
Is your hotspot running on a bridge?
What is the IP pool of the hotspot?
Ah ok now I understand your design, the SXT LTE kit has LEDS on it for alignment so you can just adjust it each time you dock. Why dont you try build a custom solution using below; mANT LTE 5o (LTE ANTENNA) 5dBi LTE antenna with 2 x SMA connectors x1 RBM33G Powerful OEM board with three Gigabit LAN ...
The WAP AC is an access point only, so you connect devices to it. SXT LTE is for internet, you could power up the WAP AC on the second POE port and put the WAP AC outside maybe setup a hotspot on a vlan for other dock users. You could put another indoor Tik device inside the cabin, if you need hardw...
Do you have a fibre terminal ont with fibre in and ethernet cable out to run to ISP modem? Can you remove the ISP modem and just have the mikrotik device? Alot of fibre connections run on vlan10 so it would just be a matter of you creating a vlan10 on ether1 and request dhcp client using vlan10. You...
The Groove 52 ac has only single chain and is L3 device, L3 meaning you can only connect one device to it.
If you need the access point to be outside and waterproof you would be best off going for
The SXT 4G kit and a wAP ac (wAP ac duel band 2.4 - 5ghz outdoor or indoor device)
Disable "allow remote requests" on DNS unless you add a firewall input rule to drop port 53 from wan side You have a vlan 10 on bridge, what is this vlan to be used for? /interface vlan add interface=bridge name=vlan10 vlan-id=10 What type of internet connection do you have i.e. FFTH. FTTC...
R2 side UltraDishTM TP 550 with MikroTik RouterBOARD RB922UAGS 5HPacD 802.11ac 866Mbps
R4 side UltraDishTM TP 400 with MikroTik RouterBOARD RB911G 5HPacD 802.11ac 866Mbps
AP on R4 is QRT AC L4
Detect Radar is causing a lot of issues with frequency selection
5785/20/an(33dBm) is R2-R4 PTP link 5745/20-Ceee/ac(33dBm) is an AP on R4 facing opposite direction to the PTP R2-R4 link R4 AP was set to AUTO frequency and it set itself to 5745/20-Ceee/ac(33dBm) The AP is running routeros-mipsbe-6.42.11, do I need to change installation is set to "Outdoor&qu...
PPPoE server on R4 see image attached I left MTU blank on the pppoe server. The client cpe I have it set it to 1480 The client is having the traffic shaping done on R4 and I see very few packet drops in the queue tab, its set to wireless default queue type. The connection to the client cpe is a qrt ...
R1-R2 5805 5Ghz only AC 5805/20-Ceee/ac(33dBm) Tx / Rx Signal Strenght -29/-28 dBm distance is set to dynamic but the link is 1KM in distance TX fluctuates up and down between 50 to 80% and the RX is fairly consistent between 80% to 90% there is always traffic going through the link Signal to noise...
Hey Petrb, R1 - R2: 802.11 ac wireless R2 - R4 is set to NV2 as I was creating self interference on the R1 - R2 link NV2 is all I can use on R2 - R4 as nstreme drops to many times due to interference. The link is passing over a small town and is picking up alot of access points in the 5ghz band. I c...
Hey guys, I'm using this firewall on wireless clients CPE's, anyone have anything else that I should include into it? /ip firewall filter add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked add action=accept c...
Hey guys, Just a question in relation to the CCR1016-12S-1S+ PSU. Is it possible to remove the second power supply and connect the pins to a din rail DC 24v 4A output supply? I have the option of battery supply and would like to be able to use it with the CCR1016-12S-1S+ in case of mains power suppl...
Hey guys, I'm having issues with my network, if anyone can take a look at the design layout and may be able to help with below issues. Bandwidth tests between routers R2-R1 Download speed 100M + (R2 - R1 is over wireless) R4-R2 Download speed 100M + (R4 - R2 is over wireless) R4-R1 Fluctuates betwee...
Hey guys, I have a LHG XL 5 ac with ROS package v6.42.11 on clients premises. LHG XL 5 ac upgraded with v6.42.11 Client speed is set to 20M download 5M upload download but cannot pass 10MB on the speedtest.net app or website. Bandwidth tests from CPE to Main router show 20M download 5 Upload, so no ...
The SXT you are using is has a licensed 3 so the wireless will be set to "bridge" mode for one only one wireless device to connect which is the workshop device. The script below has set the wireless security to workshopconnect so on the TP device in the work shop you will need to search fo...
Ok, what is it you are trying to do with the SXTsq Lite2?
Is it possible for you to reset the device and remove the default setup script.
I can assist you to setup the device without the help of quickset.
Can you do a command export file=PTP-AC hide-sensitive in the terminal of the SXT
Open the file with notepad++ and copy paste contents here or attach the file.
Anyone have the correct API to update a current profile to another profile without deleting the existing one. Here is what I have so far; <?php // Receiving variables from filled form @$device_name = addslashes($_POST['device_name']); @$profile_select = addslashes($_POST['profile_select']); use PEAR...
Hey guys, i require help removing a device using the Pear2 api Two lines of code below that I am using to remove the device. I have a form created to get the name of the device to be removed that passes the variable $device_remove $addRequest = new RouterOS\Request('/ip kid-control device remove'); ...
Hi Johannes33, pub and skins are OK in the files, just look out for the mikrotik.php file, also any scripts or schedulers you did not add yourself. Go to IP > SOCK and disable if active. Go to Users and delete any user you did not add, make a new user in a different name other than "admin"...
I think I fell victim to this attack yesterday, my clients had problems watching netflix and appeared to have two IP addresses. One IP was fake and one was the real IP address. Netflix reported the IP as using a proxy or VPN and denied the clients access. My main router was breached before because o...
Good morning Normis, I amended the Nat rules on the main router to /ip firewall nat add action=src-nat chain=srcnat out-interface=<Public> to-addresses=<Public_IP> on the clients cpe's I have chain=srcnat action=masquerade out-interface=pppoe-out1 log=no log-prefix="" unless they have a st...
Clients are showing they have two IP addresses instead of one on whatsmyip.net, one real IP and the other IP's are fake here is three IPs that showed up 66.249.81.232, 66.249.81.228, 66.249.81.234. They are not using VPN;s or proxies. I changed the IP of the main router for now and added firewall ru...
I masquerade my clients out behind one IP and for some reason Netflix has banned that IP now.
error message
Whoops, something went wrong.Streaming error.You seem to be using an unblocker or proxy. Please turn off any of these services and try again.”
Ok not sure if it's a bug but when I check "add default route" it auto adds route with the office public IP into route list as dst.address x.x.x.x and as gateway x.x.x.x and is unreachable. I have to add static route 0.0.0.0/0 gateway l2tp-out1 which is reachable, now the vpn is working co...
The issue I'm having is that LTE device is using its own public IP instead of the public IP of the remote office when browsing the internet. When I visit whatsmyip.net when the vpn is active on the LTE device, the IP is not the IP of the remote office. 0.0.0.0/0 via L2TP gateway or 0.0.0.0/0 via 172...
The SPF port failed on my RB3011 today, it was working for about 6 months straight. The setup was SC fibre with opton 125G SM WDM31 S3D modules. The RB3011 was connected to a mikrotik powerbox by fibre, I had the sfp port bonded with an ether port but no Ethernet cable connected to that ether port. ...
Strange thing happens when I try to use the add default route with the ppp dial out add default route. The office public ip is added to the ip routes but is unreachable. It adds a route Dst gateway x.x.x.x Gateway x.x.x.x which is unreachable so the public ip is been used as the dst address and the ...
Hi Bram, What kind of dns settings do you use? /ppp secret print Flags: X - disabled # NAME SERVICE CALLER-ID PASSWORD PROFILE REMOTE-ADDRESS LOCAL-ADDRESS ROUTES 0 test l2tp 1234 default 172.16.0.10 172.16.0.1 172.16.0.0/12 LTE reachable now via 172.16.0.10 LTE local network 192.168.1.0/24 Office r...
Still no luck with the nat rules. When I enable mangle on the LTE device for the private network, I cannot access websites but I can see dns requests populating on the office router
I can reach all devices on the remote office network. I want the LTE device to have its public IP address cloaked as the office network public IP and use the office router as the main gateway for all internet traffic
I can see the dns populating in the remote office router cache but the websites won't load, I have remote requests turned on for both routers, and the dns on the LTE is 172.168.1.1 which is the private ip of the remote office router
Have you created a loopback bridge with a /32 IP address on it and add the IP address to the PIM RP
On the PIM interfaces you can change the interface IGMP version to the version you need.
I can winbox into both routers from each end, Remote office side and LTE side.
When I enable the mangle rule on the LTE device the only thing that I cant do is browse a website or ping 8.8.8.8 from the lan PC
Winbox still works from each side
I can see the traffic going out the L2TP gateway with torch, when the mangle rule is enabled on the LTE device.
On the remote office router dns cache I can see the LTE devices requests in the cache.
Anyone have any input as to how I can get this working?
I setup a L2TP VPN on a mikrotik LTE device to access my office router Lan. The tunnel is established and I can ping both sides of the tunnel and reach the office router via the LTE device. I want to be able to use the office connection as the main internet connect for the mikrotik LTE device, send ...
Has anyone developed any kind of handheld tool to meter align up CPE's? This could be something similar to a Satellite Meter or CCTV Meter with an LCD touch screen, with Android OS with the Tik App / other network tools, speedtest etc.. running on it. If a company hires staff to do installs, maybe c...
Sindy, I disabled all configuration to do with pppoe-out2. Current Setup IP Route 0.0.0.0/0 pppoe-out1 Gateway Distance 1 Gateway pppoe-out1 for below Rules dst-address=a.a.a.a-IPSEC-Gateway/32 action=lookup-only-in-table table=via-wan-2 dst-address=b.b.b.b-Webserver/32 action=lookup-only-in-table t...
Mikrotik version 6.42.6 (stable) When I enable the pppoe-out1 and run command /put [resolve cloud.mikrotik.com] failure: dns name does not exist When I disable the pppoe-out1, VPN IPSEC PEER and all Policies /put [resolve cloud.mikrotik.com] 81.198.87.240 /put [resolve webserver.domain.com] b.b.b.b ...
When Peer is disabled and I run the three commands I get "failure: dns server failure" on both
/put [resolve cloud.mikrotik.com]
/put [resolve the-name-of-b.b.b.b-server]
Same results when the Peer is enabled and tunnel is established
z.z.z.z is Public IP 1 m.m.m.m is Public IP 2 b.b.b.b Webserver a.a.a.a IPSEC Gateway Results of /ip route print detail /ip route rule print /ip firewall nat print /ip ipsec policy print /ip route print detail Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o...
Have you tried adding trial to the hotspot profile on the mikrotik hotspot device, if you are using a custom login page you will have to add the trial code to a login but in the code of the page
Good morning Sindy :) Below are the results; z.z.z.z is Public IP 1 m.m.m.m is Public IP 2 b.b.b.b Webserver a.a.a.a IPSEC Gateway 0.0.0.0/0 pppoe-out1 Gateway Distance 2 0.0.0.0/0 pppoe-out2 Gateway Distance 1 Route to both are disabled in IP routes b.b.b.b Webserver a.a.a.a IPSEC Gateway Once Pref...
Still no joy with that change, thanks for your help today Sindy. I get "no phase 2" but the admin requested my static IP for his end to create the VPN, the m.m.m.m (of pppoe-out2) is showing up in the "Installed SAs" this couldn't be right as it would have to be the Public IP 1 f...
/ip route print detail /ip route rule print /ip firewall nat print /ip ipsec policy print /ip route print detail Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit 0 A S dst-address=0.0.0.0/0 gatewa...
z.z.z.z is Public IP 1 m.m.m.m is Public IP 2 b.b.b.b Webserver a.a.a.a IPSEC Gateway The nat rule was set to translate the 192.168.0.0/24 to Public IP 1 , which is static ip. add action=src-nat chain=srcnat comment="Public-Ip-1 Src-Nat" src-address=192.168.0.0/24 to-addresses=z.z.z.z The ...
z.z.z.z is Public IP 1 m.m.m.m is Public IP 2 b.b.b.b Webserver a.a.a.a IPSEC Gateway[/b] /ip route rule print 0 dst-address=a.a.a.a/32 action=lookup-only-in-table table=via-wan-2 1 dst-address=b.b.b.b/32 action=lookup-only-in-table table=via-wan-2 /ip firewall nat print 0 ;;; Wan Src-Nat Public IP ...
I could try the two public addresses active route first and if that fails, I will try the calculate 32 subnet prefixes solution. if all fails then it's at there end
z.z.z.z is Public IP 1 m.m.m.m is Public IP 2 b.b.b.b Webserver a.a.a.a IPSEC Gateway No default route for Public IP 2 Default route for Public IP 1 is 0.0.0.0/0 gateway pppoe-out1 /ip ipsec installed-sa from your z.z.z.z to their a.a.a.a to count packets and bytes but the one for the opposite dire...
I have an IP address that is for the VPN use only and not to browse the internet. The IPSEC VPN is used to access the remote webserver login portal page securely, not to browse the internet under the VPN. But when I use the IP of the webserver it will show that I can reach webserver and I can ping i...
So to recap: With tunnel down, you can access web pages by name and ping the servers by name, except the server for which you needed the IPsec, yes With tunnel up, you can access web pages and ping the servers by address, including the server for which you needed the IPsec, yes/no? no, I cannot acce...
It might be possible to do with the ether1-poe-in-long-cable, but I dont think you can power a device out ether1, think only 2-5 ports
Good idea about the media convertor, I never taught of that before
Hi Sindy, I am able to ping the webserver domain name and it translated the domain to the IP address. The dns server settings are auto giving to my via PPPoE on the mikrotik and I have remote requests on with the router IP 192.168.0.1 added to the dns list. If I turn off PPPoE "Use Peer DNS&quo...
Hi Sindy, Thank you for your very helpful detailed reply, I added /ip ipsec policy add place-before=0 action=none src-address=0.0.0.0/0 dst-address=192.168.0.0/24 place-before=0 I can now open up webserver in browser with the IP of the webserver, but when I try to go to the actually webserver domain...
Hey guys, I'm currently having major issues setting up an IPSEC vpn to remote Fortigate router. My setup SXT Lite5 ac cpe running pppoe on wlan for internet Lan is on ether1 with dhcp 192.168.0.0/24 IPSEC Configuration SRC. Address 0.0.0.0/0 DST. Address 0.0.0.0/0 SA SRC. Address my-public-ip SA DST...
Your printer is on a different network to your PC? Printer IP 10.31.10.10. PC IP 10.31.0.101
Why don't you just use the RB692 as a wifi-switch and let the CCR do the routing?
Remove IP address from Bridge and DHCP server with IP pool along with firewall rules.
Is it correct to have 0.0.0.0/0 in Src. Address and 0.0.0.0/0 in Dst. Address, looking at the wiki guides local private network address and remote private network should be used. I wasn't given a remote private network address to use and the tunnel wont establish unless 0.0.0.0/0 in Src. Address and...
I managed L2TP/IPsec server, so there is not need in accept NAT rule. Just try to ping Tik IPsec gateway from remote server and then try to ping your PC behind Tik in LAN. Also you have to be sure that remote server have a static route to your LAN via ipsec gateway IP. Hi Anumrak, When IPSEC is ena...
Note: It is recommend that the IPSEC address is NATed to public IP addressing. My nat rules /ip firewall nat add chain=srcnat src-address=192.168.0.0/24 action=src-nat to-addresses=x.x.x.x out-interface=pppoe-out1 /ip firewall nat add chain=srcnat src-address=192.168.0.0/24 action=src-nat to-address...
When the IPSEC tunnel is established, I have no internet on PC that I am trying to ping from, so I cant actually ping anything I guess or even browse to the remote webserver.
When I disabled the IPSEC tunnel internet returns to normal.
The admin said everything is in order at there end and can see my pings hitting the webserver from the mikrotik router, but I cant ping from my PC or reach the webserver via browser. VPN requirements; Route Based VPN's are the standard VPN build i.e not Policy Based VPN's. VPN selectors should be 0....
Hey guys, I have been having trouble the past few days trying to setup an ipsec vpn to a remote location, somebody might be able to point me in the right direction. I can get the ipsec connection to establish on phase2 and can ping the remote server from the mikrotik device itself but not from my pc...
Hi Guys, I have a question regarding setting up a routed network using two SXTs and two Routers. Do I have to bridge both ether1 and wlan together or is there another way without bridging interfaces using IP routes? SXT1 Wireless bridge mode IP on Lan interface is 10.0.0.2/29 IP on Wlan interface is...
I enabled proxy arp on interface sfp1 on R1 and proxy arp on interface sfp1 on R2 Then on R2 in /ip arp menu, I added the static address I wanted to give to the client on interface sfp1 Then added the static route to PPP remote address and now the client gets a static IP The client is now reachable ...
Maybe you should assign this address in ppp secret user profile as remote address? Hi Anumrak, Thank you for your reply, it was late last night when I wrote this post so I left out the stuff that I did try to solve this. I added the static IP to the ppp secret as remote address and in gives the sta...
Hello Guys, I require some help. I've received a /29 allocation of IPv4 addresses from my ISP. For sake of discussion, I will call this the 100.0.0.168/29 network. This IP space is divided as follows: 100.0.0.168/29: Subnet 100.0.0.170-174: Give out to customers 100.0.0.169: Gateway 8.8.8.8 DNS 8.8....
I had issues before with the router not picking up dns settings from ISP Check to see if the input fields are empty or contain DNS IP's Go to IP > DNS You should have DNS IP addresses in the dynamic input fields, maybe update the router to the lastest bugfix if the inputs are empty System > Packages...
Hi guys, Just wondering is it possible to use a form to increase the Hotspot http-cookie-lifetime via input field I am using below code but no joy with it. ===Form Code=== <form id="cookie" class="form-horizontal" action="cookie.php" method="post"> <input type...
If you put the web server IP address into the browser address bar on your device does it not bring you to the web-server? Are you looking to give your web-server an address like mywebserver.dns.com or something like that? if so you need to put the IP address into the STATIC DNS settings of the mikr...
If you put the web server IP address into the browser address bar on your device does it not bring you to the web-server? Are you looking to give your web-server an address like mywebserver.dns.com or something like that? if so you need to put the IP address into the STATIC DNS settings of the mikro...
Hey guys, I need some advise on a new network design, I'm currently going with OSPF, MLPS/VPLS, and a PPPoE server on CCR router, Clients use PPPoE client to get IP address when connected to AP's and radius server to manage queues, bandwidth and accounts etc... I was told by an advisor that PPPoE is...
Connect the fibre to your core router then connect the switches to router with cable and connect the APs to your switch, bridge the Aps and get the same SSID for all of them In router run a pppoe server and make a account for client or you can other config that you like for your network My only iss...
I guess you could try using the new REP wireless package, an extend the signal from one room to another using 2 hAP lites, that way you will have wireless and ethernet in the desired room
Have you tried to use ethernet power plug, something like "Powerline (One Tenda PA202 + One Tenda P202) Wireless Power line Adapter Extender WiFi hotspot 200Mbps Ethernet Network Adaptor" this might be an option
Ok that's great, looking forward to hearing your progress, remember to backup all your scripts when you have your network complete using the /export file and save on your comp
Here is a new script, I need you to reset your config on the RB951G without a default config System > Reset Configuration Tick "No Default Configuration" Press "Reset Configuration Button" When that is all done, winbox back into the RB951G New terminal and paste below script /int...
Ok I need you to reset your config on the RB951G without a default config System > Reset Configuration Tick "No Default Configuration" Press "Reset Configuration Button" When that is all done, winbox back into the RB951G New terminal and paste below script /interface bridge add a...
You are using the whole RB951G router as a hotspot, all ports bridged with wlan. Run the hotspot setup on bridge instead of the wlan. If you can post the RB951G config here, go to terminal /export file = hotspot Drag file from router to your desktop Open the file using notepad++ or sublime text edit...
You need to make sure your facing your Groove at the Harbour AP, adjust it until you get optimal signal using the scanner on the wireless card to search, maybe buy a mesh dish and stick the Groove onto instead of an Omni for better results
If the interface is called "ether1-local" /ip firewall nat add action=masquerade chain=srcnat comment="default configuration" \ out-interface=ether1-local if you still dont have connection try disable the "drop" firewall rules Use tools ping to test internet connection ...
Ok now I need you to winbox in and reset device and tick no default configuration Now edit this script and add in the ssid and password in the slots to match the Harbour When edits are complete, I need you to copy and paste script back into the new terminal on winbox /interface wireless set [ find d...
Ok If you can winbox in and go to terminal and type in
export file= harbour-script
Drag the harbour-script from files in winbox onto you desktop and open it with notepad++ or sublime text editor, copy and paste the content here, hide any passwords and any other private info you want to
Ok, you need to reset the Groove using the reset button, When it reboots keep using the default config script, Go to Wireless on left navigation bar Find security tab and add a new profile call it harbour, Add the Harbour wifi password into the profile. Interface tab Select the wireless card Use the...
Nope ignore everything I said before, follow below only Open Winbox System > Reset Configuration Tick "No Default Configuration" Now press "Reset Configuration" Winbox back in when GrooveA 52HPn reloads Select Quickset CPE > SSID OF HARBOUR AP Enter Password Configuration Tick Ro...
Ok might be best to ignore Quickset for now Open Winbox System > Reset Configuration Tick "No Default Configuration" Now press "Reset Configuration" Winbox back in when GrooveA 52HPn reloads Select Quickset CPE > SSID OF HARBOUR AP Enter Password Configuration Tick Router Mode In...
Ok can you go into Winbox Left Navigation Menu ----------------------------- IP > Firewall Filter Rules Tab ------------------------ Disable all Rules Go to Nat Tab and check you have rules ----------------------------- General = chain srcnat Out. Interface Wlan1 Action = Masquerade ----------------...
Cool, so if you connect the GrooveA 52HPn via ethernet cable to your desktop you have internet access but if you connect the GrooveA 52HPn to another Router/AP your wireless devices have no internet access? What is the Router/AP you are using and do you know if its in Bridge mode or Router mode and ...
Hi, Do you know the password of the AP on the harbour you want to connect your GrooveA 52HPn to? If answer is yes, you need to winbox into the GrooveA 52HPn Reset the GrooveA 52HPn to default again with the reset button or via Winbox, Use default setup config Now Select on the left navigation menu Q...
You are using dns servers 8.8.8.8 you need to remove that and let the router use the dns of your ISP and all you are running a script to disable and enable the wifi at a certain time this could be causing a problem if you don't have the NTP servers setup
Just had a look at the script, since this is a free hotpot for guests, you might be better of letting the guest login via trial profile, also you have radius enabled
I setup freeradius along with daloradius to manage users on my Hotspot network, it allowed new users to make a payment and create their own accounts then login into the network. Made life alot easier for me as all I had to do was make sure the internet stayed working. New user scans and finds Wi-Fi ...
Ok guys I think I got the login to work for facebook but the page needs styling, add code to your current login page and it should work. It also posts to facebook aswel see attached file, Edit the index.html with Notepad++ or dreamweaver Look for the below lines and change the appid to yours ======...