I can also confirm problem. Main router ccr1009 and hap ac established ipsec tunnel without any problem but without traffic. Then on my main router i disable firewall rule for input icmp drop, and everything is working fine. After that you can enable the drop rule, and tunnel is still working. But f...

So, i am really struggling to make this work but .... I am attaching configuration of both routers roadwarrior mikrotik is connected to the internet as wlan client with ip 192.168.0.6, over adsl router local address of road warrior 192.168.88.1 ccr has dinamic ip address .... xxx.ddns.net, local 192...

Hi all... I have 3 computers that are connecting like roadwarriors to ccr1009...it's pure ipsec...done with help of ppt from user meeting Now i would like to put one more mikrotik between to awoid separate connections.. New mikrotik is going to be behind nat, and those three computer would connect t...

+1 from me also. First i bought ccr1009PC and everything was fine with temp log. Then i moved to 1009+PC and temp checking script from time to time alarms about high temp but in health status everything was normal (i had a little script to check temp and sends email if it is getting too hot). After ...

If we set aside problem with powering (wireless powering wasn't seriously developed ever since Tesla failed to extort more money from J.P.Morgan), a wAP ac would make a good wireless hop. As both hops (2.4 and 5GHz) would essentially be point-to-point, I'd configure them as nstreme bridges. Powerin...

If the reason for avoiding LAN cables is fear for interference from power lines to UTP cables or fear for some power surges, then you could use fibre connection between the "main wireless hop" (building-2-building) and their hAP ac2 ... dumb media converters supporting multi-mode fibre an...

OK...things have changed a little bit. In the other building (where my sister lives) i have electricity on balcony. So if i wanna avoid lan cables, i suppose i could use 2wifi card hardware (or some other equipment combination) to connect my network, and on the other side her hap ac2. I need hardwar...

We have a 60m wireless wire link here with one end in a window, and the other outside which works fine.

However it may not work depending on the type of glass.

Regards
Nick

Ok...will try with 60ghz...
Any ideas for POE and slim cables?

There Are so small cables avaible that No Drilling is needed...

https://www.intos.de/produktuebersicht/ ... =5N9cjAIQM

What about POE on this cable? .... or any other slim cable?

No need for holes try something like This

https://rover.ebay.de/rover/0/0/99?loc= ... 3061020036

Use 60Ghz outside only !

very interesting solution !!!
But drilling through windows for cable is not an option.

I would look at their 60G product line. This would be the lowest cost option and it can be a window to window solution however, they do provide the following caution: "This device penetrates some windows depending on material." https://mikrotik.com/product/wap_60g They come as a pre-setup...

Hi all! Question about choosing best equipment... I want to connect two buildings, away maybe 70m. LOS perfect! Floor is on the same height! In first building is ccr1009, HFC 150/15 mbps, with ip range 192.168.32.0/24. In second building hap ac2, HFC 70/10mps, with ip range 192.168.34.0/24 and dhcp ...

Thx for your answers...

I will try with default android software and the above stated settings...

Hello everybody!
I have created my ipsec following this link...https://youtu.be/QlkIbx0Jpoo
With my laptop and ccr everything is ok, but i can' connect my mobile phone...have tried several programs from googleplay but nothing seems to work...
Software suggestin?

Bump.
Anyone?
I can explain in more details if necessary...

Thx

Hello! I have two wan connections. Vdsl on ether 1 (pppoe) and hfc docsis modem in bridge mode on ether 2 ( dhcp client). My question is if this is normal behaviour. When i open some web page (after dhcp client on ether 2 is enabled)...arp list is populated with enormus number of mac addreses. If pp...

Correct me if i am wrong...what you mean is to plug in crs both 28v and 48v adapters?

Anyone? I was searching a little bit... 1amper per port...at 28v...that is 28w per port max... Ccr is using 33w...hap ac...13w...cap 10w... So...if i have adapter 28v et 2.8amper...that is around 78w what adapter can produce... - 10w for crs...that is around 68w left... So i can power 2xhap ac,cap a...

Hello!
Simple question, not sure if i am doing in right.
I have above mentioned switch.
I want to poe ccr1009 pc sff+, hap ac x2, cap ac, and poe camera x2.
Is it possible with shipped adapter or i need to buy stronger?
Thx for your answers...

@nicob

New hex s is working ok...
Troubleshooting old hex s which is returned to seller...

I have received new hex s and everything is working fine...

When i was troubleshooting my hex i have tried only with sfp and without lan cables...problem still persisted

Ok...i have tried everything...nothing worked...
I have sent file to mikrotik support...
In meantime...will send rb to seller...
Thx for support...

Try with auto negotiate off and speed set to 1Gb/s.

I have tried that....nothing happend...no link

Hi! I have bought new hEX S and i am having problem with SFP link with other devices (also mikrotik). Sometimes it does work after a few hard resets...but usually doesn't work. I have tried with several mikrotik SFP modules (all are the same), with different haredware (CCR, hex poe, switch), and dif...

THNX !!!

Problem solved!!!

Hello! I have little problem which i don't know how to solve. I have created OPENVPN and client connection and that part is working fine. When mangle rule to route traffic over cable modem is enabled vpn client can't see NAS. Router ip: 192.168.32.1, NAS 192.168.32.3 port 6541 Client over VPN 192.16...

Hi all! I have been reading this forum for some time now, and it has been very helpfull, but i have one problem to solve. I posted my problem on this forum some time ago but i didn't find solution... I have main router 951g-2hnd with VDSL 40/8+4G E392 linked togehter with PCC - everything is working...

Hi all! I have been reading this forum for some time now, and it has been very helpfull. I have main router 951g-2hnd with VDSL 20/2+4G E392 linked togehter with PPC - everything is working perfectly. Problem is that my 4g signal is poor were my main router is located, and i have one 951g-2hnd sitti...