MikroTik

CRS328-24P-4S+RM have had voltage set option from almost the beginning of production.

Voltage set option is useful in cases, when PD support high voltage passive power source, but does not support IEEE 802.3at/af.
https://wiki.mikrotik.com/wiki/Manual:P ... t_Settings

Version 6.43rc32 has been released. *) dude - fixed client auto upgrade (broken since 6.43rc17); still need to upgrade dude client manually. Client crashes after each upgrade via client ui Thank you for a report, but can you please confirm that your Dude client (executed with the administrator righ...

Hello, sorry for my English. Could someone please tell me what would be the correct way to ground the connected equipment in a Powerbox Pro using the outgoing POE function? The housing has a connector apparently for that purpose, but it is not attached to anything, just threads in the plastic. Rega...

Since mentioned cameras support PoE (802.3af Class3), you should be able to power them from hEX PoE using a 48-57V power adapter: https://mikrotik.com/product/RB960PGS Since cAP AC supports Passive PoE-Out up to 57 V, you can try to power cameras, it might work. more information about high voltage p...

FANs speed depends from the PoE load, so in your case, if a very little PoE load will be used, you will hardly hear the FANs. About the SwOS - The FAN control is set to spin at least with middle speed, so it just not as advanced as in the RouterOS, but we plan to add the same FAN speed control to ne...

Got my WAP LTE kit today. both has loose heatsink. Luckily I inspected mine before powering it up. the heatsink is rubbing against solder, parts and antenna. pretty sure it will cause overheating or short. We haven't seen similar reports, can you please send us the serial numbers of these units to ...

atlanticd - Yes, that is the fix for the problem. Please test it and report back to us with the results. Hi strods, I can confirm that the RouterBOOT firmware upgrade to 6.42rc46 works, and it is not causing boot loop anymore. However I noticed that after firmware upgrade (and only after Firmware u...

Both standards have their pros and cons and affect only non-standard PD which support only one of these modes. If PSE supports only mode B (non-standard mode-A PD will not receive power) If PSE supports only mode A (non-standard mode-B PD will not receive power) In the same way, by using another ven...

Please note that CRS112-8P-4S-IN uses af/at mode B standard, passing PoE over 4,5 (+) and 7,8 (-) pins https://mikrotik.com/product/crs112_8p_4s_in However in this case it seems that Doorbird is not fully compatible with the standard, because: PDs that implement only Mode A or Mode B are specificall...

If you want to do this FROM the RouterOS, then you can use fetch to send a simple GET request to the specified web page: /tool fetch url="www.domain.com/url.php?id=2" keep-result=no More about the fetch command: https://wiki.mikrotik.com/wiki/Manual:Tools/Fetch Similar example based no HTT...

hello everybody i need some help i have mikrotik and 75 radio vendor "ubnt" i want get just identity from /ip neighbor and use command "put" in terminal to show the radios as list with just identity name and here is my code { :local identity [/ip neighbor get value-name=identity...

Ok so the problem here is that mAP and wAP products state that they can go up to 57v from DC-in Jack. This is false advertising as we have attempted to feed proper conditioned positive 54v from a meanwell power supply that effectively burned both mAP and wAP that we have tested. We have also tested...

You can use PPPoE server monitor command to see this value in CLI:
/interface pppoe-server monitor <pppoe-user> once do={:put $"interface"}

And store it in the global variable
/interface pppoe-server monitor <pppoe-user> once do={:global i $"interface"}

First of all I would suggest to use tools which are specially designed for traffic testing: Bandwidth Test: https://wiki.mikrotik.com/wiki/Manual:Tools/Bandwidth_Test Traffic Generator: https://wiki.mikrotik.com/wiki/Manual:Performance_Testing_with_Traffic_Generator If you still want to use describe...

By default you should see red LED only if the PoE-Out is set on forced-on or powering interface on auto mode.

If the LED lights without both two mentioned states, upgrade your RouterOS to the latest RC version, to see the PoE status in the logs.

There is not confirmed hardware problems related with the PoE-Out on these devices. PoE out status is dependent on multiple factors, for example, the voltage drop on the wires which powers your PowerBox, and the voltage drop in the wires that goes to the powered devices, both will cause current flow...

I'm not sure if the following is possible, I certainly have failed to make it work with my limited scripting knowledge, and was hoping someone can point me in the right direction or tell me it's not feasible. I'd like to track MAC-Address to port's for reference, and to avoid manual lookup when nee...

Hello, I need some script to read info from System Log and sent to value and use to other scripts. I need to read this parameters: RSSI and HCSQ. For example: /log get... not work. Maybe other solution? Thanks https://image.ibb.co/h5oiRk/gsm.png :foreach log in=[log print where message~"RSSI&q...

Thank you very much for reporting, we found that there might be some "protected routerboot" issues on RB750Gr3 (hEX r3), and only on some specific backup booter versions. If you have any related problems, please write to support@mikrotik.com Updated bakup BIOS for RB750Gr3 (hEX r3) can be...

Thank you very much for reporting, we found that there might be some "protected routerboot" issues on RB750Gr3 (hEX r3), and only on some specific backup booter versions. If you have any related problems, please write to support@mikrotik.com Updated bakup BIOS for RB750Gr3 (hEX r3) can be ...

New current version have been released. Changes in v6.38.3: *) Fixed - winbox/webfig ping probe used retry interval in retry count field. *) Fixed - wireless registration table didn't show values in all fields. *) Fixed - Device tree notification system were not working properly. *) Fixed - Client s...

What version of Dude are you using ? Please test with the latest version.

Quick tests didn't show problems. Make sure that you are dividing only integers.

Hello.
What policies i need to set for ping from Dude?
Group full make it.
Thank you.

Try with enabled test policy

Changes in v6.39rc17: *) Fixed - wireless registration table didn't show values in all fields. *) Fixed - Device tree notification system were not working properly. *) Fixed - Client started from shortcut with added arguments tried to use 2210/2211 ports joanllopart - at the moment I can only sugges...

Use only "(data-path)/files/" directory. All other directories have read only permissions
http://wiki.mikrotik.com/wiki/Manual:The_Dude_v6/Files

Hi there, i been looking at dude settings and i couldn't find anywhere how to set default Network Map for user that has only Read rights. What am trying to achieve is, to have separate user that has read rights, and once that user logins to The Dude he will load by default Network Map that has all ...

Does anybody have an idea how to change the map or submap of the device? The idea is that i have a map with devices, a little bit later a had made submaps and wont to move some devices from main map to submaps and i can't find where anf how to do that At the moment it's not possible to move devices...

At first I would suggest you to use only latest release version, e.g. 6.37.4
Make sure you are running the same version client, and connecting to winbox port

Did you take a look at this article:
http://wiki.mikrotik.com/wiki/Manual:The_Dude_v6/Files

The SNMP problem with other vendor is know, we will try to fix it. Please try latest bugfix version 6.37.4, can you repeat the SNMP issue ?

Tell me why it is missing "execute on server" ?
dude.png
Dude server is running on chr.

What Dude version are you running ?

Please do so that you can select multiple types of devices Tools
You mean to allow specific tool for multiple devices ?
dude.png

At the moment you can also specify device type. By this way you can allow tools only for specific device group.

Network = Mikrotik router 6.38.1 tage vlan125 -> taged valn125 TPLINK managed switch taged vlan125-> taged vlan125 Mikrotik router WIFI 6.38.1 WIFI router ether1 -- vlan125 wlan1 BRIDGE --vlan1 --wlan With brodge rstp or stp cant get DHCP or connectivity. without protocol mode all are OK. IT is OK?...

I have made a virtual mikrotik x86 and installed the last dude on this VM. The snmpwalk is working I see the list about the oid numbers, but if I put the numbers in the "Appearance" menu nothing happens. I will try it later with a Cambium device too. Please test 6.37.4, can you repeat the...

what about memory eating od HEX ROS v 6.38.1 and older too - after 1day uptime is memory 27MiB free and drain continue until HEX reboot (because of watchdog timer) Make sure you have fast storage drive (USB/SD card), if the storage drive will be too slow, data will not be saved in time, and will sl...

If there is no set password, you should be able to restore it with blank password:
/system backup load name=<name>.backup password=""

Please do so that you can select multiple types of devices Tools

You mean to allow specific tool for multiple devices ?

dnelson - Where do you see 4GB limit ? You can set your custom link speed under Links => Types nje431 - some quick tests didn't show any problems using Webfig Dude>Server Config (6.38.1) from Chrome/Firefox. Can you repeat this from different PC ? honnnza - Can you please write mail to support@mikro...

joanllopart - Seems like there is a small bug with SNMP and UBNT devices, can you please test with just releases 6.37.4 version ? If you get the same results, then its not related and we would need remote access (support@mikrotik.com) Chupaka - Only [CTRL]+[V] will not show > sign, you will see it i...

When will you add support for custom fonts (cyrillic)?

The problem is known, at the moment can't promise you any dates.

When will you add support for custom fonts (cyrillic)?

The problem is known, at the moment can't promise you any dates.

"If" line looks good, check logs with /log print, maybe it's Winbox log display bug (fixed in winbox 3.9) Its not a /log problem, because i have the same issue when i replace logging by using a global var: :local date [/system clock get date] :local time [/system clock get time] :global t...

Hello there
i want to get in print command only the one column results.
ip interface print , BUT to get only the NAME
or
ip hotspot user print , and AGAIN ONLY the usernames
How is that possible?
Thank you!

foreach a in=[/interface find] do={:put [interface get $a name]}

I use v6.38 (stable) ----------------------------------- Sorry, im a new in scripting, but if i run a simple script(system-scripts-run script), there's nothing in the log: my script: :log info ("Test: start script.") :if ( true ) do={ :log info ("Test: from if.") } :log info (&q...

Any idea?

Please write to support@mikrotik.com
MIB file and remote access will be needed.

I just bought a hEX to allow me to offload the Dude server from my CCR, so I can get and use all the Dude fixes in the "experimental" releases without compromising my production edge router. I did an export-db on the CCR, FTPed the file to the hEX, and did an import-db, with no errors. Wh...

I am using version 6.39. I have already tried with version 6.38 and also did not work, the SSL gets very high and the CPU goes to 100%. I am using a virtual machine and running on x86.

Please write to support@mikrotik.com
We will need a remote access.
Thanks.

HI Just moved to Dude 6.38 from 3.6, everything working smoothly so far except one issue, On some devices, if I select the Router OS option, I get the following error: recv failed: Connection reset by peer(104) (6), next attempt at 15:08:42 This only happens on some devices, I've ofc made sure pass...

Dears

I need to know which programing language use to make own tool with using variables like [Device.FirstAddress]

And can i use with batch file (.bat)

Thanks

You can use any which can accept arguments.
This means you simply need to specify how much arguments your .bat will accept.

Changes in v6.39rc13: *) Fixed - winbox/webfig ping probe used retry interval in retry count field. aTan - Administrator rights is necessary just in case, if your Dude client fails to update (so far haven't seen problem with using the Dude without administrator rights). Percanta, Chupaka - Disabling...

Changes in v6.38.1: *) Fixed - Tool fetch didn't work with notification - execute on server *) Fixed - Link type speed was not recognised *) Fixed - Broken Simple queue edit/delete feature *) Fixed - Dude showed only part of all Simple queue *) Fixed - Submap icon wasn't placed on map if "New M...

Problem is fixed in the latest release.

mschreiner - so your request would be to create hierarchical map structure with parent/child map tree structure ? Where parent map notifies about all issues on their submaps ?

Changes up to v6.39rc12: *) Fixed - Submap icon wasn't placed on map if "New Map" option was used. *) Fixed - Custom tool wasn't accessible from Devices-> List *) Fixed - Device -> RouterOS didn't show interfaces in interface dropdown list *) Fixed - Error was displayed when tried to edit ...

You have to point the Dude client to a folder on the Windows PC. You have "/disk1" in there, this does not seem like a Windows path. You must use something like "C:\\" Thanks Normis, this clears it up. What I will have to do is inform other users that they must store their mikro...

Try with enabled FTP policy

asik - thanks, reporeted.

pitersss2 - To avoid some problems related to Dude, follow these suggestions:

*) It is suggested to use only ext3 file format for the Dude data directory, it's more stable for the Dude.
*) Store your custom files Only in dude/files directory

On a system x86 based, I have some problem of memory leak using dude v6.38....every minute dude eat lot of ram until router crash...someone has this issue??

Some server crash is fixed on 6.38, but just to be sure that it's the same problem, please send us supout file

Yes, the license level will not affect your Dude performance/functionality, you will get the same features.

SSH command output can be saved with "output-to-file" option. Any other script/command output you can save with :execute command: For example - save output of your script: The script: /system script add name=ScriptExample source={ /system clock print } Execute script, and save output: {:lo...

My problem persists, does anyone have the solution?

Should be fixed in 6.38
What version are you using ?

Chupaka - Thanks, but I wasn't able to reproduce. I can reproduce it via WinBox from 2 PCs and via WebFig: as soon as I change Retry Interval and press 'Apply', Retry Count is set to that new number. it's x86, checked v6.38 and v6.39rc7 (two different routers). will supout help you? or I can give y...

AiroSam - Thanks, Interface dropdown will be fixed in next rc version. Also the server crash on 6.38 is fixed, and will be included in next 6.38.x version. maviaelsilva - Default Winbox tool is removed, please use tools to specify path to your Winbox.exe file: http://wiki.mikrotik.com/wiki/Manual:Th...

Your scheduler does not have the same policies as your script.

If you don't need to enable some specific policies, you can simply add wireless disable command without script:

/system scheduler add interval=1D on-event={/interface wireless disable wlan1} disabled=no start-time=22:30:00

rzirzi - to see last time the device was online (to see if it is used at all). It can be seen in Device -> History graph, or in Services -> Outages (show down times) Also you could make notification, and apply to this device (log, email...) Would you need some additional way ? - schedule an update i...

Hi All, Long time passed since I have been to this forum. A lot has changed, but relying on the Dude server in my work has not changed till now. Now I need to install the new version (windows version started to fail multiple times), hoping it is more robust than the windows version. I know it now n...

The last version with syslog is the 4b3. Not the previous like you wrote. And it is well known. Mikrotik promised to put it back somehow one day... You can still use Dude as syslog server. The difference is that the syslog messages will be stored under Log section. https://s30.postimg.org/40y30875t...

Dude can't be installed on RB2011UiAS-2HnD (MIPSBE)

The Dude server can be installed on following platforms:

ARM (RB3011)
TILE (CCR line)
CHR
X86 RouterOS
MMIPS

If you are using Windows, then the easiest way would be to install the CHR with Dude server on virtual machine.

Please test it with the latest Dude 6.39rc, there are fix related to tool fetch. Let us know if the problem is resolved.

Currently it's not possible to use HTTP POST method from Dude/RouterOS, so here is some workaround example how to use Telegram, to send messages using HTTP GET method:

http://wiki.mikrotik.com/wiki/Manual:Th ... am_Example

Suggestions / requests will be appreciated.

At the moment we can't promise any date about CLI Dude.

AiroSam - Please update your Dude server to the latest RC (6.39rc7), and check if device Status=up and RouterOS Status=ok

Changes in v6.39rc7: *) Fixed - Tool fetch didn't work with notification - execute on server *) Fixed - Link type speed was not recognised *) Fixed - Charts made some strange peaks *) Added - Right click tool option under Devices -> RouterOS -> simple queues *) Fixed - Broken Simple queue edit/delet...

Netinstall should work if your VM is bridged with your network. Netinstall on Linux can be used with wine. At first try to netinstall this device with option "Keep old configuration", this will leave your old configuration. Also please try to start the board with the Backup BIOS by holding...

Version 6.38 is released

Full changelog and discussions will be on this topic:
http://forum.mikrotik.com/viewtopic.php?f=21&t=116356

Version 6.38 has been released. Major changes: *) Added - AES encryption method for snmp v3 *) Added - Dude now have configuration interface in Winbox/Webfig *) Added - Network maps now are viewable from web interface (Webfig) *) Agents - Now any RouterOS device can be used as The Dude agent. It no ...

Hello everyone, I want to report a problem with the upload file function in v6.38RC52 on mmips RB750GR3 - in this version and with this device, traditional "drag and drop" does not work, but there is a new button "upload" http://pawinski.info/PLIKI/up123.png because the device h...

Quick test didn't show problems, if the monitored device is reachable from Dude server.
Just in case try to update your Dude server.

If problem remains, write to support@mikrotik.com

macsrwe - Yes you can also place your custom folder under dude/files sparrow - check if you can receive RouterOS data from that device - under RouterOS -> Interface. You should see the same results as in your link label https://s24.postimg.org/4bzkmtred/Router_OS.png "?" will be shown if n...

I can confirm our map background images randomly disappear from disk, too. We are on 6.38rc40 and have had to replace a background image twice and it ultimately disappears from disk. It is missing again now. 1. Please update your Dude server to the latest - 6.38rc version 2. If you can reproduce th...

Devs: thanks for all the work so far, appreciate it! Sorry I didn't reply with update to email notification issue not working. Original email problem (post #104) was resolved. Was originally on CHR. Loaded new x86 VM and email notifications started working so seemed to be something with that specif...

Should be fixed in next release: %HOMEPATH% variable resolve from Dude tool Typo: "Authetication Failed Winbox->Dude->Notification->Command: Reported: bandwith_test - auth. fail aTan - Autoupgrade tested with multiple devices, multiple versions, should be something specific. asik - background i...

Is the Dude client autoupdate functional? I've tried it with several 6.38rc and it downloads something and then just shutdowns.

Should be fine to autoupdate from all recent versions, just make sure that you run the Dude as administrator. Does anybody else have seen similar problems recently ?

Version 6.38rc52 has been released. Changes since last version *) Removed - Since default Winbox used in the Dude wasn't fully compatible with all RouterOS devices, we removed it completely. *) Fixed - Increased default ping packet size to 54bytes - there was some devices who wasn't able to respond ...

Check if you have permissions for dude user, the port is not restricted with firewall.
If this does not help, send supout to support@mikrotik.com

Also remember to update your RouterOS version to the latest.

Try 6.38rc
Also send mail with report to support@mikrotik.com

Version 6.38rc51 has been released. Changes since 6.38rc41 *) Fixed - Changed SSL connection timeouts. SSL connections caused CPU overload *) Fixed - Minor changes in Dude fonts *) Added - Dude icon in Winbox/Webfig The SSL problem should be fixed with this version, please test and report if problem...

Changes since 6.38rc37 *) Fixed - File upload to dude/file directory caused client crash *) Fixed - Background images could disappear on version change *) Fixed - Snmpwalk was not working properly in recent versions asik At the moment it's not in schedule, but the request is stored, thanks. dcolli F...

New current version is released! Changes in v6.37.3: *) Fixed - Broken auto update on dude client *) Fixed - Memory leak caused by dude server *) Fixed - Client radius authentication *) Fixed - Device tooltip windows wasn't able to show all info *) Fixed - Dude client might stay in 'getting stuff' s...

With this command you will also see event logs on your Dude server RouterOS logs.

/system logging add topics=dude action=memory

Version 6.38rc37 has been released. *) Fixed - default files will be stored in dude files folder if the file system does not support symlinks (fat32) *) Fixed - avoid going into loop (Dude client could get stuck in loading phase) Note ! Since dude has received major changes in recent versions, some ...

Version 6.38rc35 has been released. Changes since v6.38rc32: *) Fixed - Dude client stuck on "getting stuff state". *) Fixed - Disk name were changed on RB hEX if the dude was used on USB flash or mSD card. For security reasons it's suggested to make backups before upgrade. http://wiki.mik...

New current version is released 6.37.2. !!! Please note that the Dude client auto-upgrade to this version will not work. To update Dude client manually use installation file from http://www.mikrotik.com/download Changes in v6.37.2: *) Fixed - History charts graph issues on popup window. *) Fixed - N...

The changelog is updated, thanks.

The Dude still works in version 6.37.2, but the auto upgrade will not. This means you can still upgrade your Dude server, but for Dude client you will need to use manual installation.

6.37.2 Client can be found here:
http://www.mikrotik.com/download

This will be fixed in 6.37.3

Thank you for correcting the snmpwalk. I found other bug in rc31: missing graph captions in device history panel. Very good, thanks, and can you please clarify, is this problem only in device pop-up window (history graphs), or you also see the same in device > history charts ? Seems like there is i...

Changes since v6.38rc29: *) Fixed - Snmpwalk was broken starting from 6.38rc27 *) Fixed - Dude db-import failed if dude wasn't enabled amt - such error is showed if the connection is restricted from the router side, I wasn't able to reproduce such problem, maybe it's because of monitored device conf...

Asking for Metal9 support in Spectral Scan tool in the Dude.

Thanks!

Thank you for suggestion, this feature will be included in the next RouterOS RC version.

Changes since v6.38rc25: *) Fixed - Error on dude RADIUS authentication. *) Fixed - In some setups dude server caused memory leak on X86/CHR. *) Added - Dude server now supports spectral scan up to 7Ghz. Hello, I upgraded from 6.37.1 to 6.38rc29 and moved from CCR router to vSphere x86 CHR VM becaus...

Thank you for reporting, seems like the backup save time needs a fix. But I did not saw any problem with the session from time. Can you give more examples ?

Sessions/logs/reports show correct from time, if the customer time zone is set (6.37.1/6.38rcX)

Hello, i still trying to figure out how i can make the dude server to read RouterOS info on a RB device that dont use the default Winbox Port There are two opttions available to read RouterOS info: 1) Use default Winbox port. 2) Make firewall NAT rule on your monitored RouterOS device, to redirect ...

Thanks for reporting, links are updated now.
http://www.mikrotik.com/download

New release candidate version (6.38rc24) is available! http://www.mikrotik.com/download Changes since v6.38rc19: *) Removed - Link label will not change colour on link speed change. *) Fixed - Allow users without FTP policy to connect to dude server (access to files will be restricted). *) Fixed - D...

Starting from 6.37 file upload option is removed from dude, for the file management use Winbox, Webfig or ftp.

At first make sure you are using latest RouterOS/Dude server and dude client version, make sure you are using winbox port.

raffav wrote: Yes i know but i dont use default winobox port 8291 for security reason it will be very nice to be possible to tell dude on witch winbox port connect You can specify probe port under device settings => Services => routeros mangement => Probe Port Lakis wrote: If Dude lose connection t...

Thank you all for testing and reporting. For some reason Dude stop reading values from device - Dude cant reprobe or cant get new values from the Device These values will keep updating, but it might take some time, we will see if we can improve it. Another thing on Device label as u can see two from...

Some variables in notifications seem to be missing, for example :
[Service.Status]
[Service.ProblemDescription]

Thank you. The fix for this will be included in next release.

Changes in 6.37rc42 *) Fixed - network label scaling issue, when movied. *) Fixed - minimap issues. *) Fixed - incorrect link graph data, when interface was changed. *) Fixed - shown wrong interface on link menu dropdown. *) Fixed - various server/client cashes - Disabled upload and drag&drop fe...

Winbox 3.5 is released! Please upgrade.

Continue discussions here:
http://forum.mikrotik.com/viewtopic.php?f=21&t=111719

What's new in v3.5: *) fixed file upload via Upload button; *) do not disconnect from router if none of the windows are open; *) report error if telnet failed; *) handle properly romon authentication failures; If you experience version related issues, then please report them to support@mikrotik.com....

:put [/interface ethernet get ether1 rx-bytes]

For example - check with if there exists user with name "*adm*" :if ([:len [user find name~"adm"]]>0) do={:put "exists"} Or for those setting where you are not allowed to add same records - catch run-time errors :do {user add group=full name=admin} on-error={:put "...

To get "last-ip" from every connected device us foreach loop:

:foreach w in=[/interface wireless registration-table find] do={
        :put ([/interface wireless registration-table get $w]->"last-ip");
    }

What does log says after reboot ? Make sure you are using power supply with inaf output power, also install the latest RouterOS on your device: http://www.mikrotik.com/download If the problem repeats, generate supout file after reboot, and send it to support@mikrotik.com http://wiki.mikrotik.com/wik...

Are you using same power source - when connected to PC and Switch ?

Best option would be to generate supout file after reboot, and send it to support@mikrotik.com
http://wiki.mikrotik.com/wiki/Manual:Su ... utput_File

Please try to install the latest RouterOS bugfix version, there are several improvements for RB3011, including port flapping fix.

No this device comes without a beeper.

Doesn't this accept it before it gets to that line? chain=forward action=accept in-interface=ether3 log=no log-prefix="" You have to add accept rule for allowed (knocked) ip, and the interface should be your external (pppoe-out1) Here are good port knock configuration example: http://wiki...

Hello All, As it is mentioned in the wiki " The backup RouterBOOT version can not be older than v3.22 version. A special package is provided to upgrade the backup RouterBOOT (DANGEROUS). Newer devices will have this new backup loader already installed at the factory." However, what is the...

:put (“concatenate” . “ “ . “string”);

or

:put ($var . “string” . $var2);

http://wiki.mikrotik.com/wiki/Manual:Sc ... _Operators

body=("Interface=".$name." TX is ".$tx-bits-per-second);

:local filename;
:foreach file in=[/file find where name~"mikrotik"] do={
:set $filename [/file get $file name];
/tool fetch src-path=$filename ............
}

/interface wireless info allowed-channels <Wlan iface> Will show you all available settings depending on your current configuration, but /interface wireless info hw-info <Wlan iface> Will show all possible settings allowed by hardware, the output will be: ranges: 2312-2732/5/b,g,gn20,gn40 Where &quo...

Please read this article:
http://wiki.mikrotik.com/wiki/Manual:Netinstall

Also use only the latest Netinstall and RouterOS from:
http://www.mikrotik.com/download

Thanks for the correction, the wiki page has been updated to: As an emergency recovery option, it is possible to reset everything by pressing the button at power-on for longer than reformat-hold-button time. Even if reformat-hold-button time is forgotten, holding the reset button for more than 300s ...

This page should help you:
http://wiki.mikrotik.com/wiki/Manual:In ... figuration

You will still be able to reformat these devices by holding reset button more than XYX value.

If you are using included 24v 2.5A power adapter, then with enabled "forced-on" mode and ether1-poe-in-long-cable, all powered devices should work stable.
http://wiki.mikrotik.com/wiki/Manual:Po ... ed-on_mode

Hi, i'm new here and using mikrotik, i'm looking for a script that eliminates certains user of my hotspot on the date i choose. For example: I've created the user "William" today, I want to (if it's possible) put a script that automatically eliminate that user the 2 of march of next month...

PowerBox comes with 24v 2,5Amp power supply, which is completely fine to power four mAPL. While PowerBox output voltage is the same as input voltage (24V), one mAPL at max power consumption will require 0.145A

http://routerboard.com/RB750P-PBr2

Hello! I also got one device. Can anybody explain why this device consumes so much power 3,5W. I planned to use PowerBOX to connect 4 mAP lite, but it looks like that in this case it is not possible to use it. Even original power supplier provides 2000mA. I'm right? If so what the best practice to ...

Thanks for reporting. This problem will be resolved in next RouterOS releases.

What if you use: && instead of & ?
/ip firewall connection remove [find protocol=udp && dst-address=192.168.250.100 && .........

This link could be useful for you:
http://wiki.mikrotik.com/wiki/Policy_Base_Routing

Swithing menu can be found under this link:
http://192.168.88.1/index.html#forwarding

Check if all SFP checkboxes are marked (from - to)

In your example, if ip firewall address-list is empty, then [/ip firewall address-list find ] will return nothing - "", so conditions for: :if ( [/ip firewall address-list find ] = "") will be TRUE. Find command won't output any result to the terminal, to do so - use command :put...

:put [/interface get ether1 link-downs ];

/interface ethernet set sfp1 mac-address=AA:AA:AA:AA:AA:AA

Are you using original power supply to power 3011 ?

Please try to enable forced POE mode on RB3011:
/interface ethernet poe set ether10 poe-out=forced-on

http://wiki.mikrotik.com/wiki/Manual:Po ... ed-on_mode
(Note that the power will stay on until this mode will be changed to auto or off )

There will be no Date if log is created in current day.

You can also use simple command to change queues with unset max limit:
/queue simple set [find max-limit="0/0"] max-limit=8M/8M

Or do foreach loop:
:foreach i in=[/queue simple find where max-limit="0/0"] do={/queue simple set $i max-limit= "8M/8M"}

Here you can see step by step instructions how to use Netinstall to reinstall you router. http://wiki.mikrotik.com/wiki/Manual:Netinstall Configure your PC IP address manually, use same subnet on both - Netinstall and PC. If the board will successfully start etherboot mode, you should see "ethe...

Where must $ comming in the line? Can you make the last line please :if ($thishour = "23") do={:execute $voltreport} $voltreport is the second script or function which is not defined here. Here you will find step by step instructions how this script works: http://wiki.mikrotik.com/wiki/Mo...

This command will add all received ping src addresses to address list called "PING" /ip firewall filter add chain=input action=add-src-to-address-list address-list=PING protocol=icmp Scheduler will start the script at startup /system scheduler add start-time=startup on-event={"Your sc...

There is an error in last line:
:if ($thishour = "23") do={:execute voltreport}

if voltreport is supposed to a variable - then it is missing $ and also it is not defined.

If you change this line, then the script works fine in 6.33.5

Thanks PaulsMT, but I need an install package for smips... jan/01 00:00:04 system,info verified protected_routerboot_v3_24_enable_6_29_1_mipsbe.dpk 13:36:09 system,error can not install protected-router-6.29: it is not made for smips, but for mips 13:36:09 system,info router rebooted [admin@RB941-2...

To enable protected RouterBOOT, you have to update board backup BIOS to v3.24. This backup BIOS package can be downloaded here: http://www.mikrotik.com/download/share/protected_routerboot_v3_24_enable_6_29_1_mipsbe.dpk More info here: http://wiki.mikrotik.com/wiki/Manual:RouterBOARD_settings#Protect...

You can try the following things to make 260GSP work more stable: Use only original power supply 24v 2,5 A. In most cases when input or output voltage is not stable (caused by unstable PSU, using long cables which causes voltage drop, or by powered device), the PoE In long cable can fix the reboot p...

Find command - Returns list of internal numbers for items that are matched by given expression: To get values, you can use get+find command: :put [/ppp secret get [/ppp secret find name="myPPPOEClient"]] of "if" operator: :if ([:len [/ppp secret find name="myPPPOEClient"...

Since RouterOS 6.x simple queues target-addresses and interface parameters are joined into one "target" parameter. This code will work if there will be target with adrress=(192.168.100." . $i."/32) and total-bytes more than 5242880 { :local traf; :for i from=1 to= 254 do={ :if ([...

First please try to boot the board with backup BIOS: Enter BIOS settings while board boots (Press any key within 2 seconds to enter setup), and press: b - booter options 2 - force backup-booter loading And exit bios (x - exit setup) If the board is able to find kernel, log in and update your BIOS to...

Wireless-cm2 is the latest wireless package, it contains more optimizations compared to the wireless-fp. We suggest to use cm2 package if it's possible.

Using AP-bridge mode you have to simply create a bridge, and add both - wlan and ether to this created bridge: /interface bridge add /interface bridge port add bridge=bridge1 interface=wlan1 /interface bridge port add bridge=bridge1 interface=ether1 If you want to bridge from station side, you also ...

Are you using default wireless settings on both sides ? Check if there is set max channel-width, also look if on both ends is enabled fastest bands, try to repeat tests with whole range of supported frequencies. Check if both chains are enabled (tx-chains=0,1 rx-chains=0,1): /interface wireless prin...

With original power supply RB260GSP should power these devices without problems.

Note, that there can situations, when powered device requires more current at the starting moment, then on regular load, in such situation you should set PoE Out to "on" mode.

Stable issues have been seen in cases when 260GSP are powered with weak power supply, and in cases when powered devices are attached with long ethernet cables.

In combination with the original power supply and enbaled long cable feature, it will be completely stable.

Instruction here is correct, if there is problem with reset button, you can also use CLI to reset the board: /system reset-configuration and if this is not possible, use jumper hole to erease configuration : http://wiki.mikrotik.com/wiki/Manual:Reset#Jumper_hole_reset If the reset button is working ...

You can use "hw-info" to see all possible bands, channel widths, and frequency ranges of device:

:put [interface wireless info hw-info wlan1]

WHOLEY FANTASTIC-NESS!!!! it works on 6.33 but not on 6.29 I suspect some weird version bug... but that gets me in the right direction. curious if it will append...for me but , I'm not complaining.! Thank you :execute is a new feature, you will find it only starting from RouterOS 6.30 By the way, t...

You can also save console output with :execute command. With this example you will get 5 second traceroute output saved to TRACEROUTE.txt.

:execute {/tool traceroute 8.8.8.8 duration=5} file=TRACEROUTE

I've upgraded bridging RB750UP to 6.33.2, Power-Cycle-Ping is fixed -- THANKS MT! I wonder how often powered devices are pinged? Power Cycle Ping Timeout value? What if my device starts to reply ping in 5-10-15 minutes after powered on (f.e. Cambium heater applied when cold weather), but I want to ...

Can you please provide steps how to repeat this issue? I didn't found any problems using Webfig with RouterOS 6.33.3

Please try to add email debugging:

/system logging add topics=e-mail,debug

Run email send command from terminal, and with scheduler, look at the log output.

Also please check if server address is still the same in /tool e-mail print

Also please check IP phone POE-in pinout, if it differs from Mikrotik used standard ( 4,5 (+) and 7,8 (-). ), you should use a crossover cable.

If this does not help check the output of:

/interface ethernet poe monitor [find]

Should work with:
{
:local dhcpIP [/ip dhcp-client get [find interface=ether1] gateway];
:local Gateways "$dhcpIP,192.168.10.1,192.168.10.2"
:put $Gateways
}

Check with
:put [/ip dhcp-client get [find interface=ether1] gateway]

(in your case interface=ether1-gateway)

At the moment fix for this bug is available in our RC version, and also will be included in the next bugfix version.

Thanks for reporting, I just reproduced this bug. We will try to fix this soon.

If you don't use snmp, you can get these values with scripting. Use this script as an example, modify it to send the output over sms, email or other..: { :local iname; :local monitor; :local speedRX; :local speedTX; :local mbpsRX; :local mbpsTX; :foreach interface in=[/interface find] do={ :delay 10...

This should work: { :local re :local relo 99 :foreach i in=[/ip arp find interface=bridge2wew] do={ :local address [/ip arp get $i address] :set $re [/ping address="$address" size=1500 interval=20ms count=100] :if ($relo > $re) do={/log info "IP $address Received $re"} } }

Your NAT rule will capture only port 80, coming from interface ether2, with source address 192.168.13.0/24. Make sure that NAT parameters are set correctly.

Web proxy should work fine.

With 2 wireless cards you will get simultaneous dual band.

PeterDoBrasil - You should try with 6.33 version. Another bug? 2015-11-09 16-56-23 Скриншот экрана.png Why does it reboot my PoE device while it's online? And what about "grace period" to NOT reboot while device is starting just after power cycle and before it become ready to ping reply? P...

You can use this as an example, Here is down script - will start count timeout in seconds: { :global work true :global timeout 0 :while ($work=true) do={ :set $timeout ($timeout +1); :delay 1s; } } Up script, will stop down script loop by changing $work state, and read timeout value, if uptime is mo...

This should fix the problem:
http://wiki.mikrotik.com/wiki/Hairpin_NAT

In your case:
/ip firewall nat add chain=srcnat src-address=192.168.88.0/24 dst-address=192.168.88.252 protocol=tcp dst-port=3128 out-interface=<SERVER INTERFACE> action=masquerade

Try to reinstall this device with Netinstall:
http://wiki.mikrotik.com/wiki/Manual:Netinstall

After installation upgrade board BIOS:
/system routerboard upgrade

/ip firewall nat add action=dst-nat chain=dstnat dst-address=202.59.70.90 port=<ANY PORT> protocol=tcp to-addresses=192.168.5.155 to-ports=5551 Also add masquerade or src-nat rule for returning packets, for example: add action=masquerade chain=srcnat out-interface=ether1 Mikrotik NAT: http://wiki.mi...

It is possible to see the board default configuration with command: /system default-configuration print You can do little changes in this script to change WAN and LAN ports, after modifying the script do: 1. remove any configuration you have: /system reset-configuration skip-backup=yes no-defaults=y...

Try to use latest Netinstall: http://www.mikrotik.com/download The board appears, try to reinstall with latest RouterOS. If you are able to login to your board, you can try with command: /system routerboard settings set boot-device=try-ethernet-once-then-nand Restart the board with connected ether1 ...

Please read this article:
http://wiki.mikrotik.com/wiki/Hairpin_NAT

$IP&0.0.0.255 Very cool!!! IMHO, this should be documented in the Wiki, preferably with some example like that. Right now, the bitwise operators give off the impression they work only for integers, and not between two IPs (which I understand are treated as integers "under the hood", b...

The problem here is with pick command - picking from 6th digit to 9th digit works fine with "8.8.8.x" but it fails with higher IPs because starting from 6th to 9th digit for IP "192.168.16.x" will give you different output (6.1) Best solution is to use Bitwise operators to only t...

First you should configure your email: http://wiki.mikrotik.com/wiki/Manual:Tools/email Then use script, you can also add any other information or file to this script... { :local uptime [/system resource get uptime]; /tool e-mail send to="xxxxxxxx@xxxxx.com" subject="Some text" b...

So you want to print only AllowInet lists ?

Can do this with
/ip firewall address-list print where list=AllowInet

You can do this with scheduler:

/system scheduler add name=SSTP start-time=startup on-event={/interface sstp-client set sstp-out1 disabled=yes}

So on every startup SSTP will be disabled

You can forward already forwarded packets from your ADSL router, if the specified destination address/port will match, then the packets will be forwarded: 1. Packet from public network will reach your ADSL router with destination-ip= <ADSL public IP> on port 7777 2. Packet will be forwarded from ADS...

Do you get the same results if you create manually TCP traffic (downloading files...)? Are you using latest rOS ? You should check if the configuration and test conditions are exactly the same on both devices. If you still see queues performance differences, you should write to Mikrotik support, wit...

You can also set lease time to very small time interval, it should solve the problem.

for e.g.
/ip dhcp-server set lease-time=15s

Configuration is correct if you send packets trough ether1-gateway

/queue simple
add max-limit=15M/15M name=queue1 target=ether1-gateway

I have tested simple queues with iperf and also with regular TCP traffic, and on 6.32.3 everything seems to be working correctly.

Can you please specify in more detail about this issue, which RouterOS verision are you using, how the board locks, are you unable to connect the board trough wifi and ether ? The board stops responding to pings. On the DynaDish, it will stop passing traffic and be non-resposive to anything other t...

By default all CRS interfaces are switched, this allows you to use wire speed switching, also this means that packets will not bet sent to CPU, and your RouterOS configurations will not apply to switched ports. To use all RouterOS features on CRS you have to send packets to CPU, or tu use regular ro...

I have one 6.81km (4.23mi) link going right now. I have had it up for a month or two. I would say that it performs about as well as the rest of our MT BHs. We generally use ARC dual polarity panels in an ARC integrated enclosure with RB922s. I do like the mount for the DynaDish. The capability to a...

Please try to use latest RouterOS version:
http://www.mikrotik.com/download

Also enable wireless-cm package:
/system package enable wireless-cm2

If the problem remains, write to Mikrotik Support:
http://www.mikrotik.com/support.html

Yes it's possible, you only have to download NTP package:

More info can be found here:
http://wiki.mikrotik.com/wiki/Setup_local_NTP_servers

Extra packages can be downloaded here:
http://www.mikrotik.com/download

Guys I am so much frustrated!!!! I have DWM-157 Hardware revision D (latest) I also have RB951G-2HnD with latest RouterOs (6.32.3) on it... I can't get it to work... I can see the device under System->Resources->USB However there are no new ports created, and I can't do anything else. I have tried ...

which version is best installed on the router (MikroTik RB951Ui-2HnD). I need a stable job, once set up and forget. It is the current version (6.33RC36) stable and reliable? or better put 6.32.3 :?: :) Definitely the most reliable version is the bugfix version, it has all known bugs fixed. Here is ...

First you should update your board to the latest RouterOS:

If the problem repeats, paste your log output here, or send the supout file to Mikrotik support department:
http://www.mikrotik.com/support.html
http://wiki.mikrotik.com/wiki/Manual:Su ... utput_File

UDP on port 53 is a DNS requests which goes to server 74.116.184.28

Check this topic if requests continues:
http://forum.mikrotik.com/viewtopic.php?t=73057

All you need to do is 1. Put both interfaces in one bridge /interface bridge add name=bridge /interface bridge port add bridge=bridge interface=ether1 add bridge=bridge interface=wlan1 2. Change IP address interface from ether1 to bridge interface. 3. Create or change DHCP server on bridge interface.

You have to remove "http://" from $line,with this command you can leave string starting from "www" { :local line "http://www.google.com" :local nline ([:pick $line [find $line "www"] [:len $line]]) :do {:put [resolve $nline]} on-error={:put "DNS Does not ...

{ :foreach i in=[/ip hotspot user find where email~"@"] do={ :local mail [/ip hotspot user get $i email] :local mac [/ip hotspot user get $i mac-address ]; :put ("$mail" . " $mac"); } } This will check only users with typed some email address, and will get email and mac...

Traffic generator packet sizes can be changed with command /tool traffic-generator stream set packet-size= Also to make test more close real life, use random ranges feature in traffic generator, to simulate multiple streams with different source addresses/ ports: This example show how to create conf...

You can use multiple drop/accept rules with multiple time parameters

/ip firewall filter add time=

Time format is described here:

Time ::= Start-End,Day
Start -- 0s..1d (time interval)
End -- 0s..1d (time interval)
Day ::= sun|mon|tue|wed|thu|fri|sat[,Day*]

Search found 282 matches