Easy, in the mangle pre-routing rule exclude the ip of the Roku as source address. Or create an address list and exclude it in the mangle pre-routing rule
Last week i was using it in vacations. Uptime of 2 weeks without any issue.
The modem was flashed with the last release available from huawei previously to mount it in the waplte just for beeing up to date.
Ordered the modem on aliexpress for a cheap price
Hello I've this setup and don't know how to achieve my target. I've 3 routers (Router A, B, & C) in different locations connected through a VPN connection over Internet to a centralized router. I've OSPF lmplemented so any device of one site is able to ping and see any devices of another site. I...
Just received my brand news woobm.
In the console i'm unable to do copy and paste.
do you know how it is doable or if it's going to be a future feature ?
thanks
Hello, i have two questions about the automotive connector of the wAP-LTE :
1/ What input voltage range is support on this connector (9-30V as the Jack) to power the router?
2/ What is the usage of the Aux-In Aux-out/control cables ?
The config is quite conplicate for a beginner with no network knowledge. 1 wan is easy to setup with webfig. The second one needs to change the configuration through cli or winbox with policy routing.
The config is quite conplicate for a beginner with no network knowledge. 1 wan is easy to setup with webfig. The second one needs to change the configuration through cli or winbox with policy routing.
Have a vps with a vpn from your mtk which forwards all incoming traffic to the mtk. But it can be expensive depending of your vps provider. CHR is available on aws for example.
i'm using a couple of them and i'm not complaining. very good product. You don't need to power through both ports. only one is enough.
also check this thread : viewtopic.php?t=104540
The problem is that your lte connection may be natted by your operator. You wo'nt get a public adress. Yes you can setup a dmz is this dongle. Only 35$ on AxIEXPRESS
I reverse the ordre. I put the main wlan interface as ap bridge and setup manually the frequency according to the frequency of the ap i want to connect with a virtual interface acting as station. I find the frequency doing a background scan.
When i monitor the port without the POE injector i see this [admin@Home-RB3011] > interface ethernet poe monitor numbers: 0 ;;; Wifi Wap name: ether10 poe-out: auto-on poe-out-status: power-on but the wAPac doen't start (all leds off) if i intercale the POE injector, all is working. I use the provid...
Hello, I have a wAPac connected on ether-10. the wAPac is powered by the POE of this port. All was working fine After rebooting my router today my wAPac did'nt power on. Changed cable but still no power. I retrieved the POE injector provided with the wAPac and connected it. The wAPac started working...
You can also set the ip address og the mtk as a dmz server in the huawei router. Like this all incoming traffic will be redirected to your mtk wan port.
If you use Linux then go to command lines. There is no profitable interest to port winbox to linux. Have you ever developped graphical interfaces on linux ?
On wapAC after upgrading from 6.37.1, it was unable to get a dhcp address lease. I needed to downgrade back to make it have a lease again. It's a wAPac so no master slave ports !!! my wAPac is configured as a CAP. eth1 is configured as dhcp-client. 6.37.1 i get a dhcp lease 6.37.2 i don't get a dhcp...
Hello, I'm trying this setup Hapac-Lite connect to a wAPac. wAPac is connect on port 5 through POE. I use a 24V 1.2A powersupply. to power that. After a couple of minutes, the hAC-lite is unresponsive and bricked. I've to restore it to make it work again. (Netinstall) but it crashed again. I don't k...
I see a performance diference between ports. My setup is the following SFP=> Wan (down 800Mb/s up 250Mb/s bandwith) eth1 Master of eth2-5 eth6 Master of eth7-10 bridge eth1 & and eth6 Speedtest with a cable from eth1 ==> 780Mb/s down 240Mb/s up Speedtest with a cable from eth6 ==> 650Mb/s down 1...
If you check the diagram of the CRS, all ports are connzcted to the cpu through only one 1 gb/s link. I use the sfp port with one copper gigabit and i m able to route all my bandwith. Almost 800Mb/s
Sfp can't be master. It's not on the switch. I'm using it as the wan port with a sfp and i'm getting around 700Mbps download an 200Mbps upload on speedtest which is my current isp allocated bandwith.
For a WISP mode : I've wlan1 as a ap-bridge and second as (virtual AP) as pseudobridge /interface wireless set [ find default-name=wlan1 ] band=2ghz-b/g/n channel-width=20/40mhz-Ce \ country=france disabled=no distance=indoors frequency=2437 \ frequency-mode=superchannel mode=ap-bridge name=wlan1-lo...
Set the fist wlan as an ap bridge and the second as pseudobridge. First we be the ap and the second the client
If i do the contrary i am unable to connect to the ap
On ROS 6.3.3, After resetting the configuration in winbox, i couldn't get the default configuration.
The only way to have it it's using netinstall.
Is this feature missing in 6.33.3 ?
Hello
I'm resetting my hap lite ros 6.33.3 and i couldn't get the device to have the default configuration. The router restart with no config. Is it an issue ? Thanks for your support.
Just a stupid question, i understand the benefits of using Fasttrack. Where can we found a simple explanation on how to implement it with some examples?