Hello, thanks for the response. The company is going to make an upgrade, the mikrotik ccr1009-7g-1c-pc with this configuration can go? I am not an expert in mikrotik and the configuration was not made by me. Even with CCR1009 you still dealing with slow network. because your configuration is not op...

Is winbox telling you wrong pass or Could not connect?
can you connect with Ether 2.
we can not answer you unless we know more about this situation

Your configuration should be lot more optimized than what its here. There could be lots of reason for your cpu exhausting problem with this kind of configuration. I would just name one of them because it takes time to review all of them. You should not use content in the way you are using it. using ...

Hello, I have been tasked to propagate a VLAN across 2 different routers. The easiest way that comes to my mind is to connect both routers with a cable and configure the required VLAN on both ports. For some reason I haven't managed to make it work so far and I was wondering if I am missing somethi...

I've just bought a Mikrotik HAP AC. I want to setup VLANs. As I gather there are many ways to do vlans, am I correct. But I read that the recommend method for the hap ac is to use the switch chip vlan. If the other methods work aswell please let me no and how to configure it. How do I create vlans ...

Hi All, I recently bought a RB4011 and after unboxing hooked in a Mac into ethernet port 2. The DHCP is not able to assign me an IP add the laptop results in a self assigned ip. There is no Wireless network being transmitted as well (starting with 'MikroTik...'). Are there any additional steps that...

Hi guys, Finally I have failover with recursive routing working (attached). Used mainly Tomas Kirnak approach (many thanks!). I have a question about it. I notice that not always come back to main connection, let say, router goes to isp1 which is main, primary connection, fast but unstable, when mi...

This is wrong. You can check it with simple scenario 0% - 50% available traffic used - green 51% - 75% available traffic used - yellow 76% - 100% available traffic used - red The truth is green - a class the actual rate of which is equal or less than limit-at. yellow - a class the actual rate of whi...

update is very nice

/ip pool add name=IPSECVPN ranges=172.31.0.2-172.31.0.31 This is the Best and simple config for apple device /ppp profile add change-tcp-mss=yes local-address=172.31.0.1 name=ipsec remote-address=IPSECVPN use-encryption=yes /ppp secret add name=test password=test profile=ipsec /interface l2tp-server...

/ip pool add name=IPSECVPN ranges=172.31.0.2-172.31.0.31 This is the Best and simple config for apple device /ppp profile add change-tcp-mss=yes local-address=172.31.0.1 name=ipsec remote-address=IPSECVPN use-encryption=yes /ppp secret add name=test password=test profile=ipsec /interface l2tp-server...

/ip pool add name=IPSECVPN ranges=172.31.0.2-172.31.0.31 This is the Best and simple config for apple device /ppp profile add change-tcp-mss=yes local-address=172.31.0.1 name=ipsec remote-address=IPSECVPN use-encryption=yes /ppp secret add name=test password=test profile=ipsec /interface l2tp-server...

I have gor problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

I have gor problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

I have gor problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

I have gor problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

I have gor problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

I have got a problem with mikrotik ip sec for Apple ios
the log :
Failed to get valid proposal
Failed to pre process ph1 packet(side :1,status : 1)
phase1 negotioation failed

what shall i do ?

you can see http://www.imfirewall.us/ to find all of the regular expression
example for viber : ^.*viber\.com$.
/ip firewall layer7-protocol add comment="" name=viber regexp="^^.*viber\.com$"

tnks