MikroTik

KennyPowers

Hello, If I buy these two devices will it be possible link them with the SFP+ ports using S+AO0005 10Gbps Active Optics direct attach cable? Will it be also possible to USE the POE in Port for backup power and a backup link to the switch? Thanks for your help, I am looking at buying this set up tomo...

KennyPowers

To answer my own question Its a good idea to set up RoMON before starting. <Solution> SXTLTE Configure 2 VLANs on ether 1 (vlanLTE - 100, vlanMGT - 99) Assign vlanMGT an IP address something from the main router subnet. Switch menu add VLAN 100 to ether1 and CPU (Not sure if CPU is necessary) and do...

KennyPowers

Downgraded to Stable 6.34.7 - I will install again later and do that.

to which version you downgraded?
Could you provide a support output file from Beta version when it doesn't work and also from the downgraded version where it works.

KennyPowers

Have the SXTLTE configured for Passthrough on ether1 - when using the cell lock feature the main router does not get an IP address from SXTLTE downgraded and all working ok again.

KennyPowers

Hello, Any chance you can share your vlan management config? Thanks Hi Edit: have you tried with a phone, for same provider? I'm using SXT LTE kit for backup line. Just did a test and I can't complain http://www.speedtest.net/result/7861969630 . Do note that both up- and download are manually (queue...

KennyPowers

Anyone any ideas?

KennyPowers

Still trying to figure this out, should the LTE interface passtrough to a vlan interface also?

In the mean time I've set up RoMon on both devices which allows me access for anyone else stuck with the vlan like myself.

KennyPowers

Hello All, I have configured my RBSXTR with LTE Passthrough as per the wiki. My main router is RB3011. Could anyone explain how to set up a management vlan between the two as per below taken form the wiki I am using ether1 on both devices. It is suggested to create additional connection from the LTE...

KennyPowers

File sent

Thank you

KennyPowers

It was powered off all day I just plugged it in when I got home and tried connecting via winbox. When I switched it off the previous evening it was working. Powering the board with POE using the supplied adapter, also tried powering the board direct at DC socket. After reset the default configuratio...

KennyPowers

I just got home only to find the LTE interface is now gone, WiFi has also disabled itself. I have tried a factory reset, default config removing the sim powering off/on but I can't get it back. I also downgraded the firmware to the supplied firmware 6.39.2 still no luck. I also noted upon powering u...

KennyPowers

Thanks Uldis,

I never considered the different radio in the iPhone.

The old version there was an Info tab that showed all the information you mentioned but the new version this tab is gone. I am using webfig I will send a screen shot later and also check winbox.

Thanks again

KennyPowers

Hi Uldis, Both are using band 20 its an iPhone 7 Plus, I am now using wAP LTE on current build 6.40.3 no difference and the LTE package is installed. When I first set up the wAP LTE when I got it with the factory firmware the Status/Info on the lte1 interface was there, but after I upgraded to the l...

KennyPowers

Having the same problem very disappointing I was expecting big things from this product, did you find a solution?

KennyPowers

Hi All, When comparing LTE speeds on my new wAP LTE kit 6.41rc34 using the same band and in the same position as my iPhone the wAPLTE is always slower. Using speedtest.net with the same server and also trying horizontal and vertical position the wAP LET is always slower results below. is there any e...

KennyPowers

**Edit: Looks like this issue is something to do with the routing mark. Moved to bug fix 6.34.6 all working again. I have a VPN client running for some devices in an address list all was working fine before the upgrade now none of the devices can connect to the internet. The VPN is connected and if ...

KennyPowers

You can easily bridge different vlans together in ros. Thanks I was going to try that later, so will I just add VLAN 1 to ros and add it to the management bridge which contains VLAN 99, currently I have ether2 port tagged as VLAN99 in the switch chip for port 2 and switch cpu, will I need to remov...

KennyPowers

Hi All, I am using RB3011 I have all my devices tagged with VLAN management ID 99, But there is one switch where the VLAN management ID is set to 1 as default and this can not be changed. Rather then changing every device on my network to VLAN 1 is there any alternative? Is it possible to route VLAN...

KennyPowers

Where I was getting stuck was the 2 seperate switch chips you need to add your VLANs to both master ports and also bridge both sets of VLANs together for the whole switch to work along with bridging ether2 and ether6. Alternatively you could add all VLANs to interface bridge-local where ether2&e...

KennyPowers

When using the switch chip and CPU for VLANs should the VLANs be set up on the main bridge-local or the Master interface. I have them set up on the Master interface Ether-2 but I do't get an address from the DHCP server (Each VLAN has its won DHCP) but when I move them to bridge-local everything see...

KennyPowers

I have this working now, I have one issue I hope someone can help with. VLANS are all set up on master port 2 Bridge-local contains ether2 & ether6 All CAPs register and connect and the vlans get the correct ip when connected on ports 2-5 CAPs connected 6-10 register but the don't don't get an i...

KennyPowers

Ok so I got this working with bridges now to figure out the switch.

One problem all my vlans can see each other is there anyway to block this and stop them reaching the router admin panel?

KennyPowers

That's the problem I can't get this to work.

Yes I can manage the wireless centrally, but can I use Vlans on the ports so I can use the switch along with the wireless.
Sure you can use VLANs on the wired ports. Just login into your CAP device and set the required VLANs as usual.

KennyPowers

Yes I can manage the wireless centrally, but can I use Vlans on the ports so I can use the switch along with the wireless.
I don't need to centrally manage the Vlans on the switch (CAP) once they are set and working thats all I need.

KennyPowers

Allow CAPSMAN to add the switch ports on the CAP as interfaces

KennyPowers

Hi Guys, I asked something similar before but I just can't get it to work so I simplified what it was in the hope someone can give me a better understanding diagram attached. I have CAPSMAN RB3011 and the CAP RG951G all set up I can split the wireless devices by adding them to different bridges in t...

KennyPowers

I'm looking to do the same thing, any chance you could share a print of this config? In the meanwhile i got it work. I use switch-chip feature for VLAN-Tagging and forgot to assign both VLAN's to switch_cpu "port". Now everything works fine. ;-) Thx for your assistance! eMuell I've read yo...

KennyPowers

I had a look at the Mikrotik switchchip guide, I can't figure out how to use it in this instance whenever I enable it I loose access to everything. Any chance you would have a clearer example? Thanks Make a bridge on ether1 of the CAP If the CAP has an IP address or DHCP client on ether1, move it to...

KennyPowers

I am having the same problem, can you explain what you did to fix it? I fixed the problem with the help of Mikrotik support. The problem was that in my routes I had my Gateway set correctly but my Interface was pointing to my phisical connection. After I removed the Gateway interface everything work...

KennyPowers

I just upgraded from 100Mb to a 400Mb connection, without the Hotspot enabled I get close to 400Mb down and 40Mb up but when its enabled users on the Hotspot only get about 90Mb down and users not on the Hotspot get about 180Mb. Also the login page for the Hotspot has gone very slow. I am using a rb...

KennyPowers

I am trying to achieve this?

small.png

KennyPowers

Planned diagram attached can anyone help with the config for this or point me in the right direction.

network.png

KennyPowers

Using a RB3011 as CAPSMAN & RB951G as CAP with ether1 connected to RB3011 is it possible to use VLANS on the switch and ether1 as the trunk?

Thanks

KennyPowers

Hi Guys, Can anyone help me here I have my RB3011 set up as CAPSMAN (All working fine) with 3 RB951G's I wan't to set up 2 WiFi networks Public and Private and also set the switch ports on each RB951G to Public and Private so Port3 - Private Port4 - Public Port 5 - Trunk On the RB3011 I also need sw...

KennyPowers

Hi All, Could I ask someone to have a look at my firewall rules below and suggest any improvements, mistakes or additions. Thanks I've been reading up a bit and copied most of the rules form various sites. Support list is all local LAN 192.168.88.0/24 /ip firewall filter add chain=input action=accep...

KennyPowers

Hi all, I set up a VPN client as per this guide below, I route 3 devices out over this. When I dial in on the VPN server I can't connect to these devices or ping them if I take them off the VPN client they show up again. Can anyone suggest a rule I might be missing? https://support.hidemyass.com/hc/...

KennyPowers

Thanks but I dont follow how do I give bypassed users access? Also this is connected away from the main router via a switch also on the switch is a hot spot ap

KennyPowers

Hi Guys,

I hope someone can help out I have a hotspot network set up 100.100.100.1 and I have a server app running on it 100.100.100.100 is there a way only bypassed users can access this and block everyone else on the hotspot side?

KennyPowers

Hi Guys,

I have a device set up on the network wich is visible to all hotspot users, is there any rule I can put in the firewall that will only allow bypassed users to access the device?

Hotspot users range 10.10.10.50 - 10.10.10.250

Device IP
10.10.10.10

Thanks

KennyPowers

Hi Guys, I have VLANS set up as per this link http://wiki.mikrotik.com/wiki/Manual:Switch_Chip_Features#Example_-_802.1Q_Trunking_with_Atheros_switch_chip_in_RouterOS_v6 all seems to be working as in the correct DHCP address are handed out to clients on different VLANS. The only issue I can't figure...

KennyPowers

Was the LAN - WAN throughput issue fixed I found about a 40% decrease in speed on a 250MB connection vs 6.15 which always offered the full 250MB. This was all tested with default config.

KennyPowers

I had UDP port 53 blocked this was causing bypassed users to loose connectivity. Any ideas why it was just the bypassed users?

KennyPowers

Got it sorted needed to allow UDP on port 53

add chain=forward comment="Allow DNS" dst-port=53 protocol=udp src-address=\
10.10.10.0/24

KennyPowers

Hi, Here is my firewall the section with ip address 10.10.10.0/24 is the public hotspot I only want to allow ports listed and drop everything else which seems to work ok, Only problem is if I add a mac address to the IP Bindings section in the hotspot to bypass the login page they have no internet a...

KennyPowers

Can anyone help here, when I add a mac address to IP-Bindings to bypass the login page it works but they loose internet access. the hs-unauth rule the hotspot addes to the firewall seems to be causing this?

Does anyone know how I can fix this?

KennyPowers

It looks like the hotspot default firewall rules are blocking bypassed connections

hs-unauth

anyone know how I can fix this?

KennyPowers

Here is what worked for me, just copy and past into user profile, script - on login :local date [ /system clock get date ]; if ($user = "vip" ) do={ :local mac [/ip hotspot active get [find where user=$user] mac-address] :local host [/ip dhcp-server lease get [find where mac-address=$mac]...

KennyPowers

All the mac address I have added to binding as bypassed work for a few minutes then are blocked with no internet access. any ideas?

KennyPowers

Thanks for the quick reply, would you have an example I have no clue about Javascript.

Thanks

KennyPowers

Hi,

What would I need to change in login.html so the username is always sent as lowercase?

KP

KennyPowers

Here is what worked for me, just copy and past into user profile, script - on login :local date [ /system clock get date ]; if ($user = "vip" ) do={ :local mac [/ip hotspot active get [find where user=$user] mac-address] :local host [/ip dhcp-server lease get [find where mac-address=$mac] ...

KennyPowers

anyone know of a working script that will automatically add a certain user name/ or user profile MAC address to the binding profile after they log in?

KennyPowers

Hi,

How do I run these scripts I've been trying all morning with no joy running v6.15

KennyPowers

Is there anyway way when connecting to the hotspot, a mac address could be forwarded to a different lan?
The lan the hotspot is on, has most ports blocked in the firewall, I wanted some users to have unblocked access. is this possible?

KennyPowers

You are a legend thanks a mill

KennyPowers

All this can be done using hotspot although it may require a few tewaks to get it working per your requirement, I'm only after getting one of these myself so sorry can't I can't help more just yet still reading up on it.

Do a search on hotspot and you should find what you need.

KennyPowers

I upgraded from.V6.15 to V6.28 and found LAN to WAN throughput took nearly 40% speed decrease. Would anyone have a link to V6.15 so I can downgrade?

Thanks

KennyPowers

Hi, I have the following set up below and it seems to work ok, I would like to do this on the switch chip to spare the CPU does anyone know how I go about doing this? I Am using a Mikrotik RB951g-2hnd - V6.28 Thanks /interface bridge add comment="VLAN 100 Bridge" name=bridge-vlan100 protoc...

KennyPowers

Lets try.... The switch chip config is a little confusing... but I "think" it would look like this... /interface bridge add comment="VLAN 10 Bridge" l2mtu=1584 name=bridge-vlan10 protocol-mode=none add comment="VLAN 20 Bridge" l2mtu=1584 name=bridge-vlan20 protocol-mod...

Search found 59 matches