MikroTik

trace323

Your config is wrong.

trace323

You might want to change your username and password.. Only way they are infecting the Mikrotik again.

I have over 5000 Mikrotiks in 6.43.8 no issues at all with getting infected..

trace323

Hello All,

I haven't gotten a response back .. SO yeah

This sucks a lot..

trace323

Please write to support@mikrotik.com and describe the problem in more detail.

I have emailed support.

Thanks,

trace323

Mikrotik has mentioned few times, bandwidth test should not be performed on the router itself. In your case, maybe some changes were done to generator logic making it more heavy... -- Nothing has changed on my end. I am runinng the test from my Mikrotik to the the Btest Mikrotik, which I've done so...

trace323

There is to ways around this. It's an easy fix. I had the same issue but I was able to come up with a fix.

Thanks,

trace323

My friend has AT&T Giga Fiber. he had to set their device to bridge mode and it worked without issues.

trace323

Hi All, I have been using Mikrotiks for a very long time and I am started to notice a trend when I am running a bandwidth test off my Mikrotiks. For example, lets say I have a 500/500 Fiber Connection. I would normally run a bandwidth test first for the download and get 520, and upload 500. Then I w...

trace323

Remove that low quality RB3011.

Need to piut a CCR-1009.

trace323

Has the issue been going on for a while? What kind of Mikrotik and OS firmware version?

Also, I have roughly about 3000+ Mikrotiks and I dont have that issue. I use a hotspot as well.

trace323

Based on what you said below, they're not getting the portal page to agree to the terms? Or are you saying they can connect to the AP and then get dropped off?

Or get connected to the AP and wont get online?

Can you give more info regarding your config/ layout

Thanks,

trace323

You need to change the the router to a CCR. A CCR will handle it without issues. But lately with the new firmware I have notice there is speed issues now days.

trace323

The btest process itself uses quite a bit of CPU. Results will always be lower than the device supports if the CPU is being maxed out or nearly maxed out by the btest process. This is false. the CCR only goes to 1%. I notice they are issues with the CCR with speed now days. I have a 500/500 Fiber P...

trace323

Any other ideas?

How should the rules be? Can you provide an example?

Thanks,

trace323

Hi All, Hope all is doing well. I need some assistance . We are using a Mikrotik for our PBX System. We are going to be using SIP trunking. We have two phone systems internally on 192.168.1.2 ( First one ) and the second 192.168.1.3 They're requesting for our 192.168.1.2 - through specific wan IP ad...

trace323

Check computers, servers etc. behind your router if they are sending emails. Just observe connections in the firewall or torch WAN interface. The problem is I have an ISP With 600Mbps I can't manually observe the traffic. Can I just block a specific port or something that may send spam emails? Plea...

trace323

It seems your Mikrotik is infected. You need to locally login and disinfect that Mikrotik.

It's giving me an error 'Could not connect (port 8291) - connection refused.

I am sure password and username are correct.

How can I log on again through winbox please.

trace323

Hi nabilx,

Your Mikrotik Router is infected. You need to disinfect and change your password.

-

trace323

Hi, I believe your Mikrotik is infected. Please export the config, but of course hide all sensitive information. @3firs, Did you get it figured out??? I have been having the same trouble here too, some customers say they get that error as well. Obviously Netflix sends them to the ISP (me), but i hav...

trace323

Hello.

It seems your Mikrotik is infected. Look at your config..

Check IP>SOCKS
IP> WEB Proxy

You might want to look at your filter rules and NAT rules. There's a rule there catching all that data..

trace323

Hello

Anyone else experience is this as well?

trace323

I found a way around this. It works like charm and have no issues.

trace323

I am puzzled by your problem, have routers (my own home router for example) doing software VLANs for years, zero problems. If you're using latest ROS, latest firmware, and have netinstalled the router, and still experience the problem, generate a supout in that same moment and send it to support wi...

trace323

Anyone???

Anyone??????

I need some help on this.. People say they've had similar issues and some people say they dont...

trace323

Hello,

Can anyone help on this?

I mean hopefully someone is experiencing the same issue as me.

No firewall rules, plain and simple hotspot.

Anyone?

Thanks

trace323

Hello All, I have a simple setup . CCR1009 ETH1-WAN ETH8-LAN I have a hotspot running. Guest first have to agree to terms and condition page. Once they agree they can get online. I've notice a lot of my complaints guest can't use there VPNs while behind the MT Hotspot.. I don't have no firewall rule...

trace323

Yes, I did edit the export. I removed the unnecessary stuff from it. I have done a dhcp debugging. It seems the Mikrotik dhcp does the offer but nothing back from the user. Not sure if the packet is going all the way through or not. Ofcourse i cant do wireshark on a user laptop. Yes , I do add vla...

trace323

What firmware are you running on? If so anything above 6.33.3 firmware causes that issue. it's a bug..

trace323

What firmware are you running on? If so anything above 6.33.3 firmware causes that issue. it's a bug..

trace323

Same problem here on late IOS and stock android 6 devices. Anyone with a smart idea? Hello All.. I have the same issue. This is the not a Mikrotik issue. This is a OS Android issue. By default browser on the the Android device it will do that/ Don't ask why but there is NO fix at all for that.. Do ...

trace323

Any?
Anyone else?

trace323

It's gets very irritating because I have a lot of sites where I have Mikrotiks deployed and I have this issues in a lot of them. I have different users throughout the world. I hate removing the vlan and readding the vlan because I really shouldn't have to do that. I'm not sure if anyone else have t...

trace323

As long as the ip, dhcp server and hotspot server are all set on either the same vlan or bridge interface it shouldn't make no difference vs using a bridge with just the vlan por added. BTW, why horizon=1? I have never experienced the problems with vlan interfaces you mention. What is the CCR firmw...

trace323

jul/01/2016 22:22:19 by RouterOS 6.32.2 # software id = # /interface bridge add name="Guest Bridge" protocol-mode=none /interface ethernet set [ find default-name=ether1 ] l2mtu=1588 name="ether1 - WAN DHCP" set [ find default-name=ether2 ] l2mtu=1588 name="ether2" se...

trace323

Hello All.. I have a CCR1009 on a property. I have a 350/20 TWC Connection. I use a hotspot a simple hotspot config. I use vlan 100 for wireless traffic. CCR Setup ETH1-DHCP (TWC) ETH7 - MGMT Network ( 192.168.0.0/24 EHT8- LAN (192.168.10.1/21 Core Switch 26 POE Port. I have 1-15 Ruckus AP's. All...

trace323

Go to Bridge > Ports > Select one of the stuff u have here > then for Horizion put 1 on each one. That will isolate all of them from each other.

trace323

Hello.. Please go to IP>DNS> Remote request and uncheck it. This will solve any issues. Also you can do this as well. /ip firewall filter add action=drop chain=input dst-port=53 in-interface="ether1 - WAN" protocol=\ tcp add action=drop chain=input dst-port=53 in-interface="ether1 - W...

trace323

Make sure to uncheck " allow dns remote request" .. Also do this /ip firewall filter add action=drop chain=input dst-port=53 in-interface="ether1 - WAN" protocol=\ tcp add action=drop chain=input dst-port=53 in-interface="ether1 - WAN" protocol=\ udp This is the best wa...

trace323

This could be many reasons why it's doing that.

Vlan.
guest might be disconnect/reconnecting
guest is not able to obtain an IP address to due Vista.

Vista and Mikoritk are known to have issues. I have this issues alot my self.

Do you have a hotspot running?

trace323

At first glance there seems to be an issue with DHCP when running on a bridge. When an interface is slave to a bridge it seems that it doesn't respond to DHCP client requests. What's really weird is that I have numerous installations with bridges and DHCP server running on them without a problem wh...

trace323

I really don't think it's that. I will be doing more trials this week on several Vista PC's. I will trying without a bridge, with a bridge, without a hotspot. with one. I will also try just trying a default config and see how that goes.. I will post the results.. I know it's something with the Mikro...

trace323

How would I disable that?

Thanks

trace323

I really think Mikrotik staff needs to get involve with this... I seriously think it's an issue with Mikrotik itself, not a config issue.

I have tried several things and still had no success..

Anyone else trying to mimic the same thing? Anyone has any input on this?

Thanks..

trace323

I have ditched the guest bridge and same thing. I am running into the same thing with and without the Guest Bridge. The reason why I have a guest bridge it's very easy to manage things well in my aspect. It should work fine with the Guest Bridge, this shouldn't affect the DHCP. Since I do have a hot...

trace323

Maybe you're missing something when creating the bridge.. So this is the way I have it.. ETH-1 WAN ETH8-LAN goes to a GS728TP Switch. I have 10 APS here, no VLANS. I go to bridge > add bridge > create the Guest Bridge > Than go to IP > Addresses > add new > 192.168.8.0/21 for the IP and the interfac...

trace323

I understand now, my apologies. When I mean they don't get a valid IP address , I mean they get a self-assigned IP address of 169.254.X.X . This is consider a self-assigned IP address and not receiving a proper IP address from the DHCP for example : 192.168.10.40 255.255.248.0. 192.168.10.1 They sho...

trace323

How can it be my configuration? If i can simply remove the Mikrotik and put a basic router and they get a valid IP address from my DHCP Server? I have over 50+ Mikrotiks deployed and when users come to the property and they're running on Windows Vista and Windows7 Enterprise they cannot obtain an IP...

trace323

DHCP Bug with Mikrotiks.. Hello Everyone.. Hopefully Mikrotik staff reads this as well.. I have over 100+ Mikrotiks deployed and I have issues with the majority of them. After carefully going through each Mikrotik and looking at them Mikrotik has a HUGE/SEVERE Bug in the DHCP. I have a CCR 1009 ETH1...

trace323

Hello Everyone.. Hopefully Mikrotik staff reads this as well.. I have over 100+ Mikrotiks deployed and I have issues with the majority of them. After carefully going through each Mikrotik and looking at them Mikrotik has a HUGE/SEVERE Bug in the DHCP. I have a CCR 1009 ETH1- WAN ETH8-LAN Goes to a G...

trace323

Sorry for the late respond, But i'm still having a major issues with this. I notice this a lot on my properties

I will attach a picture here to see what I see on my end. I just find it weird. I only get issues with Win7 Enterprise and Windows Vista .. No other OS have issues..

Example1.PNG

trace323

trace323

I use a lot of Mikrotik in a lot of my sites. I've had alot of issues with Windows Vista Issues obtaining IP address. Usually they way around for them to see my portal page, I manually assign them a static IP address and than they can see my portal page and get passed it and get online. Lately I've ...

trace323

So it seems there's a huge problem here with thise two versions of OS. Mikrotik Layout > ETH1 > WAN ETH9> MGMT ETH10> LAN From there we have APS and switches. It's very simple. It seems in different properties, people that have Vista and 7 Enterpersie won't pick up DHCP from the Mikrotik. We have to...

Search found 53 matches