MikroTik

G2Dolphin

From the Quick Guide of that beast:

This device needs to be upgraded to the v7.0.2 or the latest software version to ensure compliance with local authority regulations!

Looks like MikroTik is preparing something powerful to announce... 👀

G2Dolphin

It could be used for running some scripts in RouterOS. You could set it in "System-RouterBOARD-Mode Button" menu. (RESET button as well, as you could notice in the RouterBOARD menu)

G2Dolphin

*) m33g - added support for "/system gpio" menu (CLI only);

I don't have M33g, but... does that allow us to play with unused GPIOs for simple stuff like turning some load on and off with relays or having additional status LEDs? That would be awesome! :D

G2Dolphin

Don't know if that is related to this particular update, but RB3011 couldn't boot anymore after updating from 6.47.6, being restarted every time after "Starting services" stage. I've tried NetInstall to 6.47.8 and 6.47.7 without and with config wipe — no success. Long story short — I've re...

G2Dolphin

. ? someone did this before ? ... looks viable ... but I'm 55-60 bucks away from knowing for shure ... . I've successfully used mAP 2nD with 3G USB-modem powered by USB OTG Y-cable. The power from male USB-A goes into female USB-A port and OTG-microUSB, and the data pins from last one goes into fem...

G2Dolphin

Can't believe my eyes. L3 HW offloading and Linux kernel v5.6.3, what a jump from v4.14. What's next, WireGuard and HW NAT?

You're amazing, guys! Gonna play around with spare RB3011 to test everything.

G2Dolphin

BTW, just because there is 0 printed on it, don't assume it's 0 ohm.

Be that what it may, as others have said... There's way more wrong with your RB than a blown resistor. There's a reason why it blew.

I've measured it before posting.

G2Dolphin

0 Ohm.

20200213_230404.jpg

G2Dolphin

Have any special instructions been given? I see a netinstall and an npk, do you need to use netinstall or is it enough to upload the npk and reboot? Is it limited to certain ARM devices or can it be used on all of them? (I have an unused LHG ac that I could try it on) No other instructions was give...

G2Dolphin

I can't read that!

* 7.0beta1 available for testing.
* For 5G-devices and other modems
* More information on MikroTik.com

G2Dolphin

From Russian MUM 2019. Currently available for downloading from http://mt.lv/v7.

G2Dolphin

You should buy mAP-2nD, an upgraded version with 802.3af support on both ports (ether1 for receiving power, ether2 — for powering other devices).

G2Dolphin

Nowhere to proof it have jumped over 32-bit counter (cmon, MikroTik, you're trying to fix that almost for 10 years

), but that last link up time from the future...

121 days + 497 days of counter limit = 618 days as for now.

uptime.PNG

G2Dolphin

RackMount.

G2Dolphin

Haven't plugged it yet. You are from the "don't turn it on - take it apart" clan? (Dave Jones) No, I'm from "posting right when I saw" one. Besides, I've answered there's no other differences on the second post, where I got home and turned it on. Отправлено с моего Redmi Note 3 ...

G2Dolphin

Any hardware changes? Switch chips now both Gigabit? CPU upgrades? Wifi upgrades?

Haven't noticed any.

These changes have also affected the RM variants as I've posted before with a full size USB port now provided.

Oh, great news. I hope we start getting them soon.

G2Dolphin

What can I say? FINALLY. Haven't plugged it yet. RM version too, please. Also, slightly redisigned font on the box. https://uploads.tapatalk-cdn.com/20170419/870b2dcddb8e74657445b63109341f07.jpg https://uploads.tapatalk-cdn.com/20170419/efef029d6a04d7ffdb0ffbe0af077a9c.jpg https://uploads.tapatalk-c...

G2Dolphin

Never seen that big changelog yet.

Thank you, and a have a happy New Year!

G2Dolphin

I bought it two weeks ago, but it can be an old stock item. I also wish to know, how to distinguish the "new" revision of the board. If this is a "fixed hardware", then i have a bad news IMG_20161222_1631442.jpg I also have this on the MB, but testing via multimeter shows everyt...

G2Dolphin

Mostly 6.35.4.

G2Dolphin

I think it's better to give some freedom to users via some "button"-assignment menu, just like you can assign different statuses for different LEDs. Maybe this is what MikroTik is already doing, if you can remember some unusable MODE buttons on new boards.

G2Dolphin

I agree. While "require safe-mode" policy in user management can be somewhat hard to implement, I believe another tiny Winbox checkbox that would simply click the safe mode button for me in the beginning is really useful and easy implementation of that idea. And if this really will came ha...

G2Dolphin

I wish Mikrotik devices had usb type-c usb-pd compatible power input. I wish too, but, to be honest — microUSB on the mAPs and etc doing it's work as good as it needs to be. But the questions of durability of connector, yes... mine old mAP2n had some connection issues and reboots if I'll move USB-c...

G2Dolphin

OMG, what a beautiful design! I'm really surprised by mAP lite, hAP lite TC and hAP AC lite TC designs...

G2Dolphin

hellow :D Im Rangga from Indonesia.. i have 4G LTE Huawei modem E3372, but it dont work in Mikrotik router RB951G-2HnD, the router can't found LTE interface of modem.. can u help me please ? tell me how to flashing my modem into a HiLink mode Plenty of information. Personally I've used russian 4PDA...

G2Dolphin

So, in summary, can we pass 802.3af PoE in to the mAP2nD and get 802.3af PoE out of it?

Not sure about 802.3af in ether2, but an active PoE device turns on instantly and works well...

IMG_2016-11-17_215324_HDR.jpg

Снимок22.PNG

G2Dolphin

Never use quickset

That's enough in 90% times.

G2Dolphin

is the smaller device with dude server feature.

RB750Gr3

G2Dolphin

Yes
https://routerboard.com/RB3011UIAS-RM

Sent from my C6833 using Tapatalk
RB3011UiAS-2HnD-IN
UiAS 2Hnd IN

It is too. Delayed.

G2Dolphin

mAP 2n and mAP 2nD http://uploads.tapatalk-cdn.com/20161021/d3b94d14bc323a32f96a8cc3a960564e.jpg http://uploads.tapatalk-cdn.com/20161021/a194575e025482804eac3a7a9a773629.jpg http://uploads.tapatalk-cdn.com/20161021/6843a14187dedbf2011120561368bd06.jpg http://uploads.tapatalk-cdn.com/20161021/6d3f06...

G2Dolphin

RB750Gr3 available for order in F-Center in Moscow (No tech details in the list though).
Going to have one tomorrow.

Thanks for information! Probably gonna take a look too. Thinking of replacing 951G with it.

G2Dolphin

Old versions will be able to connect to 6.38 as well?

G2Dolphin

Try to force-set 1G speed on the SFP interface.

G2Dolphin

Oh, that's why I got an mmips architecture package some time ago when downloaded all archs of some ROS version... What a nice HW upgrade.

G2Dolphin

So you're added fixes from 6.38rc too... nice, gonna test today.

G2Dolphin

Now with the old versions download links. Nice job.

G2Dolphin

MikroTik works with 100Mb/s link on SFP? O____o

G2Dolphin

Looks like there's an upgraded version incoming — mAP-2nD. Probably it will.

And it arrives! Interesting that mAP2n dissapear from official routerboard.com site.

Some differences besides dual-chain WiFi and more faster processor (QCA9531 on the new, AR9331 on the original)?

G2Dolphin

netinstall works only on ether1. nowhere else.

Did you notice the words "alternate methods" in the topic name?

OP try to explain it all in support via e-mail, it will be faster and probably Tik techs will help you in another way to reflash it.

G2Dolphin

Just a simple LED that shows power receiving, no matter of connected device and it's status.

G2Dolphin

mAP2n and other routers won't work as Ethernet adapter, though I as an mAP2n owner thought about this too.

G2Dolphin

That's okay. 6.36+ is more "hungry" to sector writes due to "refreshing" feature that keeps data integrity in place.

G2Dolphin

Looks like there's an upgraded version incoming — mAP-2nD. Probably it will.

But honestly dunno how it can support it while being able to be powered on from USB.

G2Dolphin

Today i receve my hAP AC. I have cooper sfp module 10/100/1000 like this one http://www.kst-bg.com/shop/hi-tech-man/sfp_copper_10_100_1000 and it's not working. I try to force ethernet of the sfp to 100 and 1000 but it's not working. I guess it's a compatibility issue. Anyone using a cooper sfp ? M...

G2Dolphin

Use a Passive PoE feature and a 24V — 5V converter, for example. Passive PoE can be turned on and off too, and "stupid" enough just to give voltage without any devices.

G2Dolphin

From where is listened thar sounds when works on 5ghz ? From router inside ?

Yeah, I haven't tested it without case. Probably drossel or something.

G2Dolphin

Just got my hAP ac, here is the detailed photos of the inside. Click to fullsize photos. http://s12.postimg.org/4coh08czt/IMG_8317.jpg http://s12.postimg.org/slizy72rt/IMG_8318.jpg http://s12.postimg.org/wfcg7ck3t/IMG_8319.jpg http://s12.postimg.org/v98g8jvt5/IMG_8320.jpg http://s12.postimg.org/nvt2...

G2Dolphin

any suggestions are greatly appreciated!

Check you have wireless-cm2 activated in System - Packages.
And yes, this is hAP ac topic, it's an another device.

G2Dolphin

I'm sorry for the dumb question but I've never used MikroTik products before. Is there a way to use 1st port on the LAN side to power the router over PoE? Thanks. Yes, just add it to your LAN bridge. Or, if using chip switching, use master-port. I'm using this in 2011UiAS. LAN device powering route...

G2Dolphin

Who can provide result of performance testing?

http://routerboard.com can.

G2Dolphin

I see that the new hAP AC unit supports poe-in @ 11-57 volts. Anyone know if it will support proper 802.3af/at?

Looks like no.

G2Dolphin

Hehe, even MikroTik themselfs posted a link. %)
$129 is quite high though... even hEX as a router is cheaper and more powerful (BTW, why? They have the same CPU, aren't they?).

G2Dolphin

LTE package enabled
wat
For MIPSBE there is an extra package available: lte-6.xx-mipsbe.npk.
On my RB750G I had to load that package first before I could use my LTE stick.

Thanks, never noticed it... very interesting.

G2Dolphin

Not a very elegant solution, but for ocasional use try 'clusterssh'. For a more robust management API or scripting will be your best bet. You can also set up SSH keys and issue commands via SSH: ssh -i private.key yourusername@192.168.88.1 '/system resource print' Hmm, seems like a solution. I'll t...

G2Dolphin

Why so? I have the hAP ac at home as my access point. In our country, we get speeds 100-500Mbit at home, so even just for an AP you need power. I also have a few devices with no WiFi, so the extra ports help. My idea is using hAP ac just as AP is overkill. I count it as a dual-band router. WAN comi...

G2Dolphin

God, people, this is an access point - an ACCESS POINT. Access point doesn't need FIVE gigabit ports, 128MB of RAM, SFP ports and a PoE-Out in most cases. cAP is an access point. mAP lite is an access point, and even SXT HG5 ac is a better AP. If "hAP ac" have "AP" in the model ...

G2Dolphin

Run a script or API which connects to each router and executes the command.

Thanks for answer. Yeah, thought about that, but I probably won't be able to create it. Do you have one?

G2Dolphin

Happy that it's finally here, but I'm a little disappointed to see a 3 year old SOC used, for an AC product it's really late to market. Hopefully now that MT have experience with developing consumer AC devices we can see more powerful products in the future on a faster release cycle as new SOCs are...

G2Dolphin

Is it possible to execute the same command on multiple routers, using The Dude, some SSH scripts or other tools?

If it's not possible on Dude, it's a nice suggestion, huh?

G2Dolphin

Hi, I am trying to send the WOL command from ssh as follows: /tool wol mac=MY:MAC:ADD:RESS interface=ether2 tool wol mac=MY:MAC:ADD:RESS interface=ether2 /tool wol mac=MY:MAC:ADD:RESS tool wol mac=MY:MAC:ADD:RESS when I take a tcpdump on the target machine, I get no response [root@localhost ~]# tcp...

G2Dolphin

Could be something with bad sectors. Try reinstall with Netinstall and then see if upgrade works

Yeah, except I wrote in that post that this is fresh NetInstalled device:) can you advice something else, please?
It's a MUM device, if that counts...

G2Dolphin

All uploads and upgrades go into the RAM. You don't need big NAND for uploading and upgrading. What about this, Normis? http://forum.mikrotik.com/viewtopic.php?f=3&t=101670#p515982 I have something wrong with mine hAP lite? Sorry for offtopic. input voltage is between 11V-57V ... will it also s...

G2Dolphin

the image looks like there is a switch or something right behind the USB port - unless that is part of how the enclosure latches together? I'm curious about what that is. RESET button. ...and exactly how you gonna utilize that memory in router targeted for endusers? If you need more storage for sur...

G2Dolphin

Thanks for naming ports "1-2-3-4-5" on the case. I just can't get used to these "Internet-2-3-4-5" namings, especially remembering RouterOS multi-WAN capabilites. By the way, it's a new top length of device "internal" name — RB962UiGS-5HacT2HnT. %) UPD: "Storage ty...

G2Dolphin

Definitely hardware. You have power problems (power supply or some internal components failed) — the BOARD just can't start it booting process.

G2Dolphin

Pins on motherboard

Well, using that single photo on this thread, look like these pins are on bottom left.

G2Dolphin

Anyone knows which are the serial ports?

Do you have any in System - Ports? If not, what exactly are you looking for?

G2Dolphin

Facepalm.

But thanks for the useful for another members info, strods.

G2Dolphin

btw: it seems storage has increased since few months/years to 128 MB ? I saw people complaining about the space available on the device.

Decreased to 16MB on some boards.

G2Dolphin

Of course, I can buy RM version, but the case is too long, and it's inconvenient to buy additional parts from different sellers to set up Wi-Fi.

By the way, you can't. It's impossible to add WiFi to rackmount version because of missing PCI-e.

G2Dolphin

I think "The Dude" is better for your solution. This is a monitoring tool by MikroTik itself.

G2Dolphin

I Got it. It's so tiny. Great product !!!

Photos? Tests? Screenshots?

G2Dolphin

passive PoE is cheaper to implement no need for expensive injectors and or switches, that's why mikrotik uses passive PoE to make devices and implementation more affordable. It's always better when device supports 802.11af too. If you don't have PoE infrastructure -- add splitters and use passive P...

G2Dolphin

Wanna know too. Heard about some script to connect to each SSH and execute commands, but can't find it. And, maybe, there is a better way? Is it possible with Dude?

G2Dolphin

RB3011 line doesn't have any fans.

G2Dolphin

Hi,I don't understand where I can download The Dude,can someone help me?

New version of Dude is a ROS package for x86, CHR and tile devices. Select "Release candidate" chain and a proper architecture, there will be "The Dude server/client" links.

G2Dolphin

Hi,

I think you can disable the led's by removing all entries under system ---> led's menu

hAP lite have only "user-led". I've seen only one device, when ALL leds can be configured (except power, of course) — mAP.

G2Dolphin

Needs a managed switch. With "dumb" switch only link reservation is possible, and even a loop without proper setup.

G2Dolphin

I think some of you are forgetting it's name... hAP... as in Access Point. Despite the name, APs doesn't need an fire gigabit ethernet ports and really big cpu power, sometimes even SFP too. hAP ac obviously is more than just an AP, seems like it's positioning is to replace old 951G, and I want fro...

G2Dolphin

Have you bought them directly from MikroTik?

G2Dolphin

http://routerboard.com/RBmAPL-2nD What a beauty! Looks like this is best designed MT router for me. It doesn't have a USB host? In that form-factor it can be really useful. Seems like original mAP-2n will be upgraded soon to dual-chain mAP-2nD too. Maybe this time with not-passive PoE too? :) UPD: ...

G2Dolphin

It's "Mikrotik certified consultant" asking us?

I can only think of VLANs and using secondary router as a switch, but MikroTik doesn't have special software to stack routers, and even possibility to do this as some other vendors do.

G2Dolphin

i think thats too much (for "budget", low-cost SOHO device) im okay with SPI, but see 2x or 4x increase in size - Reasonable(for safety purposes). but prefer SLC-alike tech in it, like "SuperMLC" announced recently or SLC itself. 30x-40x more flash resource ? for "only"...

G2Dolphin

just delete that package from files in the package list use the check for updates button off course be sure hap lite has internet access Please, don't count me as an idiot. I've specially installed "bugfix" 6.32.3 firmware to show people what's happening. This is fresh hAP lite without an...

G2Dolphin

If nothing changes, then only option will be to reinstall this device with Netinstall:
http://wiki.mikrotik.com/wiki/Manual:Netinstall

Topic starts with "Cannot netinstall"...

G2Dolphin

You definitely have some other then default packages installed, with default bundle package everything is ok. Снимок.PNG What I definitely have is a strange hAP lite out here. This is a good example of fresh NetInstall'ed device, but after some time HDD space isn't usual 8.2MB free, something near ...

G2Dolphin

Waiting for hAP AC to have Gigabit Ethernet ports...

Definitely will have. I'm hoping for 128MB flash storage, not these cheap 16MB NAND's.

G2Dolphin

Correct file paths please.

Read whole thread please.

slaystin - It is done for purpose (something like double check) so you could see that wireless package will be lost after upgrade. If we would remove it automatically then only notification about it would be changelog.

G2Dolphin

i think is a good idea to reboot device before upgrade to free ram I'm not even talking about RAM. I had enough of it to update, but only 4k KB in NAND -- so it failed in downloading. I have a mAP2n with "flash" folder -- no problems, what goes in root -- goes to RAM, but my hAP lite does...

G2Dolphin

RouterOS is upgradable in-place from RAM - update files are not saved on flash.

Say that to hAP lite. :/

G2Dolphin

Yes, I do have a device on this port.

Do you use PoE feature for this device? If not, try to switch it to "forced off".

G2Dolphin

It isn't possible. Maximum you can get is use a capable virtual OS on CCR devices with tileGX architecture, when metaROUTER will be available (possibly in RouterOS v7).

G2Dolphin

Is something connected to ether10 port?

G2Dolphin

Sometimes you need to clone an ONU ID and a password to connect too. But this is impossible on ONU from MikroTik.

G2Dolphin

update to latest Linux Kernel ???

Dunno last or not, but MikroTik updating Linux kernel only in major versions.

G2Dolphin

IS-IS is not supported in the Kernel

Well, we're expecting an kernel update in ROS v7.0...

G2Dolphin

I'm successfully used backup dual-WAN setup couple of times, routes was set up as: WAN1 route with 8.8.8.8 as Dst.Address, with Scope: 10. Main WAN1 route with 8.8.8.8 as gateway, with Distance: 1 and Check Gateway: ping WAN2 route as usual, with Distance: 2. This setup pinging Google DNS using firs...

G2Dolphin

There's mine similar topic down out there http://forum.mikrotik.com/viewtopic.php?f=3&t=102895
The most similar product in words of upgrading is RB3011UiAS-2HnD, in words of 3X3 ac — hAP AC.

G2Dolphin

Does wireless settings are identical in both cases? Probably the TX-power setting and external antennas of 433AH can cause this problem. Too high signal.

G2Dolphin

The arm (or RB3011) version of ROS seems like really unfinished... LCD menu troubles, Partitions, now Profile...

G2Dolphin

Mikrotik supports only Atheros-based cards. 7260HMW is an dual-band (not dual-radio) card, so you can choose to use 2.4Ghz OR 5Ghz but not both at the same time. I haven't seen dual-radio mPCIe card, so I think dual-radio RB3011 is impossible. Well yes, that example wasn't very good, okay. :) So......

G2Dolphin

I would rather see possibility to run two separate radios in 3011 at once than to be able to select one or another radio, even if it could be dual band. Yes, that's what I meant too -- 2.4 and 5 Ghz at the one time wit some miniPCI-e card. Just like hAP AC (lite) models -- wlan0 is 2.4Ghz radio, wl...

G2Dolphin

If i Separate the Powering Pairs from the Data Pairs & use the Power Pairs as an input on a Step-Down Converter (24v 0.5 A -> 12v 1 A) Won't that work?

This should work, because MikroTik just gives out power, no matter what is connected... if even connected.

G2Dolphin

I'm just an average MikroTik user, but quite interested in new 802.11ac devices incoming -- hAP AC and RB3011 models. Seems like hAP AC is still doing it own way to market, but we already have a rackmount version of RB3011, so, I assume, desktop 2HnD is incoming. Because of useful miniPCI-e slot, I ...

G2Dolphin

Hi! Thanks for Your Previous reply! I Just had a Continued Question: Can I use a Step Down Converter (DC-DC 24v -> 12v) to reduce the voltage to 12v and then use it to Power the Device? I am running RB2011 on Adapter only. Shipped adapter was 24v 0.8A. Router is not able to Power another device if ...

G2Dolphin

do you use untouched 'from box" windows or real-world boxes affected by Windows Update ? Second ones, sequently updatable by Windows Update. Last time I used it on Win10, just run it as administrator, set up the device's IP (hAP lite), and after powering the hAP lite in netinstall mode I've se...

G2Dolphin

I heard they changed something in SIP helpers on last firmwares, so I can advice you to upgrade to the latest 6.33.3 and test it again. Oh and change "/ip firewall service-port set sip disabled=no". This is that SIP helper I'm talking about. ----- Помню они что-то упоминали про SIP в одной...

G2Dolphin

Mine E3372h is working well with RouterOS after flashing it to a HiLink mode. I have a LTE interface appearing, and after getting DHCP address from modem's internal router I have access to the Internet.

G2Dolphin

I hadn't often use Netinstall, but never had any troubles on Win7/8.1/10. I don't turn off any services and just allow Windows firewall to add it in whitelist.

G2Dolphin

So it won't have any settings regarding ONT authentication — password or SN change possibility?

G2Dolphin

I agree. Sometimes asking someone to push a button is easier, than travelling to the router by yourself. At least there will be a good reason to use these LCDs.

G2Dolphin

10/100Mbps Ethernet port

Meh, I can't see a reason for this device to exist without 1Gbps port. Yes, cheap, but why do we need 802.11ac PtP then?

G2Dolphin

is it somehow related to this?

What's new in 6.34rc1 (2015-Nov-06 15:50):

*) new product support added

I think this is about GPON SFP.

G2Dolphin

I understand that is the switch chip, not the CPU.

So in RB750Gr2 as a CPU, and in RB3011 as a switch, CPU just goes offline?

Or two gigabit switches like this, one with one CPU core = dual-core unit?

G2Dolphin

taken from catalog

http://download2.mikrotik.com/2015-Q4.pdf

3011.jpg

Notice the CPU — it's Atheros QCA8337-AL3C, with MIPS architecture.

G2Dolphin

prices on pre-orders in most web-sites tend to be "approximately" and usually tend to be put "slightly optimistic" for marketing reasons(i guess:) ;) as for hAP prices in particular shop - thats perhaps old stocks from times when RUB cost 2x more in $. they one of 3-5 biggest MT...

G2Dolphin

You can use VLANs and a smart switch to "extend" one RB port for many smart switch ports.

G2Dolphin

A russian webshop has the RB3011 in preorder here:
http://www.lanmart.ru/mikrotik-rb3011uias-2hnd-in.html

It's the version with a 2 GHz wireless card.

If i'm correct they sell it for 8662 RUB witch is approximately €120,-

And hAP AC for 3000 RUB (less than $50), aha.

G2Dolphin

When is it coming to market?

When this questions' counter will reach 9000.

G2Dolphin

Any news about the release date of the HAP AC?

November approx.

G2Dolphin

How does it look like? Old 2011 or crs fasshion ? There's quite much info already on this forum, photos included. :) It's 2011 predecessor, "outdoor" differences is full-size USB3-port and gigabit ports 6-10 (PoE on port 10 still there). I could see an mini-PCIe wireless card inside. No o...

G2Dolphin

All you RB´s are GBit now, but you can't deliver proper POE Devices?

RB3011, by the way, will have PoE-capable gigabit port... Thinking about this, maybe some kind of gigabit-PoE device is incoming too.

G2Dolphin

do you have hap ac (no lite) winbox like this screenshots?? No. I couldn't connect to it with default login and password, and nobody knows (or wanted to told me) a password. :? By the way, hAP ac have reeeeeeeeeeally long board name (RB***) Other thing I've seen live (and in winbox) is RB3011, and ...

G2Dolphin

LTE package enabled

wat

G2Dolphin

NetInstall tool can save your configuration and upload any RouterOS version to your hardware.

G2Dolphin

1GB of RAM, by the way, as it was seen on MUM in Winbox.
Seems like a little overkill...

G2Dolphin

Do you have a source for this info?

Russian MUM. I've seen dual band hAP ac lite and hAP ac in live, Janis and Sergejs said that it's in sertification state and will be available approximately in November.
They have USB 2.0 interfaces and two wlans in Winbox.

hap_ac_lite.jpg

G2Dolphin

Till November, guys.

G2Dolphin

Now I have 2 options; 1. When I finish the work I have to close each window one by one to get a clean state again (and then of need open only these needed for for the desk girl.) 2. I just close the session with all its windows, or it gets closed because some event, and next time I open the session...

G2Dolphin

No, it's okay for me (RB2011UiAS-2HnD). I don't think this is software bug in your case. You can reset configuration and Netinstall RouterOS "from the blank page", but this is probably all you can do.

G2Dolphin

By the way, MikroTik, why not to add this, really useful on some installs, feature?
Just some days ago wished I could rotate LCD interface.

G2Dolphin

So... 6.33rc5 now, still no changes on this topic. MikroTik, will you do something with these rules, or they're solid now?

G2Dolphin

*) ethernet - added support for new ASIX USB Ethernet dongles.

Which ones? AX88179 USB3.0 Gigabit adapter isn't working.

G2Dolphin

By the way, had an 2011UiAS which heated up to 80°C after 10 minutes of first time boot... reboot fixed that problem.

Working for months now.

G2Dolphin

option to change the behaviour of that LED

Every LED (except Power, of course) on the mAP2n is configurable.

G2Dolphin

I'm missing nothing. If I'm on 6.31 and set it to "bugfix only", it should NOT download 6.30.2 (we are in the upgrade menu, not downgrad). It should download bugfix updates of the CURRENT INSTALLED release, that would be 6.31.1. So since this version is not available, it shouldn't downloa...

G2Dolphin

Will these firewall fasttrack dummy rules be allowed to be switched off?

G2Dolphin

Tools - Traffic Monitor isn't working. did it work in previous version? Personally I can't answer this question, because I found how it can be useful just yesterday... but regarding to this post http://forum.mikrotik.com/viewtopic.php?f=21&t=98370&p=490761&hilit=traffic+monitor#p490761 ...

G2Dolphin

Tools - Traffic Monitor isn't working.

G2Dolphin

It's great that you have so much attitude, thanks for that. Maybe if you look at the other thread, someone started it in the wrong forum. The RB3011 is a RouterBoard product, and therefore the reason for starting a thread in the "RouterBOARD hardware" forum. But hey, thanks for that great...

G2Dolphin

It's great that you have so much wondering to start an another topic, but there are enough ones about RB3011. Why just not to ask there?

G2Dolphin

I can advice you to wait for RB3011. Or hAP ac, if you need a faster WiFi too, but it have a slower processor.

G2Dolphin

it will be cleaned up in a future release, but maybe not in 6.30.x .

Why not? It's not a really complex problem. But it's MikroTik choice anyways — to remove it, or not.

G2Dolphin

http://routerboard.com/RB951Ui-2nD Now we got 951Ui- 2HnD and 951Ui- 2nD . :D And the old 951Ui-2HnD looks slightly better... 128MB of RAM vs 64, more powerful WiFi and slightly wider range of receiving power... versus 650Mhz newer processor at lower cost. But, of course, this model replacing the 95...

G2Dolphin

Not only these rules are mess for some people (including me), they are just cannot be deleted! Considering everything (obviously excluding some deep system things) in ROS can be set up by us, this is a step backwards. I can understand these rules if they were unique. But they are just showing the sa...

G2Dolphin

Please, add a checkbox for disabling dummy fasttrack rules.

G2Dolphin

Had an config-reset on 951G an year ago after power loss, and a "bricked" (I had to use NetInstall to revive it) mAP 2n after many losses in a couple of seconds (bad quality of power-jack used to power). After this all I'm trying to use a shutdown command every time I can.

G2Dolphin

Please, add a checkbox for turning off these dummy statistic rules for FastTrack. I don't understand, why do we need them, since we have this counter on IP - Settings.

G2Dolphin

Nice one, I'm voting "yes" too.

G2Dolphin

How can I switch off the default dummy fasttrack rule in the filter? What sense in it anyway, we have the same counters in IP-Settings...

G2Dolphin

Add this as first filter rules, if your firmware is 6.29+. /ip firewall filter add action=fasttrack-connection chain=forward comment=\ "FT established/related connections (forward)" connection-state=\ established,related add action=fasttrack-connection chain=input comment=\ "FT establ...

G2Dolphin

Had some config resets after power loss on 951G and mAP 2n... so I'm preferring to shut down the router properly.

G2Dolphin

You can use a smart switch and VLANs...

G2Dolphin

I'd prefer to have some way to downgrade or upgrade firmwares.

NetInstall, I think... but this isn't a good way, yes.

G2Dolphin

Now, I'm clueless what to do to disable webfig on the public ip.

/ip service set www address=192.168.88.0/24

This example restrict WebFig only for clients from default MikroTik LAN.

G2Dolphin

Upgrade of a legend, huh? I really like it's coloring.

G2Dolphin

quick qustion: is there a way i can program my AP to start and shutdown on a defined hour? for example durring the night i would like to have it off. Yes, just a little scheduler script, for example, "/interface wireless enable wlan1" at certain hour, and "/interface wireless disable...

G2Dolphin

So, is there an option to PREVENT RoS to get power from PoE/Ether1 ?

No options like this in ROS. You can configure only PoE-OUT options.

G2Dolphin

Great news! I really waiting that release... after buggy 6.28.

G2Dolphin

I guess the Winbox main icons has been changed as well.

No, the Winbox haven't changed since 3.0rc9. But just after installing RC of 6.29 I saw them.

And there are still old icons when connection to some older firmwares.

G2Dolphin

Noticed new action icons on the "Firewall - Filter Rules"... and they are damn pretty! Does all icons will be new, just like them?

G2Dolphin

For downloading any firmware, copy link for current one and just change version number in the link by yourself.

You shouldn't lose any configuration, but, of course, it's better to do backup and an export of configuration.

G2Dolphin

This will be fixed in 6.29. Install an 6.29rc20, if you don't want to use 6.27, it's already fixed out there.

G2Dolphin

A. Long time to be detected by WinBox Mine is not... B. No access from Winbox to mAP with default config - via IP and via MAC Then how did you manage to set up it?.. Never seen that too, though. And the biggest problem: G. Backup files vanish after reboot so there is no possibility to make backups....

G2Dolphin

I have a RB951G-2HnD and it's almost perfect for what I'd like to use it for. With the following modifications/additions it'd be perfect: - Additional 5Ghz radio (it only has 2,4Ghz) - 1 POE-out capable port instead of POE-in - Slightly -even- thinner case (it's just a tad too thick to fit nicely i...

Search found 165 matches