In the Manager tab where you enable the capsman you will see that there is a section that says "Upgrade policy". It should appear as "none". The CRS112-8P-4S-IN model has MIPSBE architecture while the CAPac has ARM architecture. If you keep "Upgrade policy" as "req...

Hello,
Make sure that in the configuration of the capsmanager you have configured "allow any version". most likely you have configured "requires the same version"

hello, for 50/60 clients Wap AC is a good option.
All access point are wired ?

Everything is wired yes. No mesh or anything like that.

Thanks in advance.

Hello,
you configure capsman on rb4011. If all configuration is well, you shouldn't have problems.

hello, for 50/60 clients Wap AC is a good option.
All access point are wired ?

Metal 52 ac is only 1x1 and does not support 2,4 and 5 GHz simultaneously.

Hello,
How many clients will the installation support ?

Hello,
if you have VLAN configured in the installation because you have segmented traffic, then if you need to specify the VLAN.
If you do not use VLAN, then you only need to add the MAC of the host and it is not necessary to specify the interface or the VLAN
Regards.

Hello Heidarren.
I think you should configure hap ac2 and cap ac as CAP and configure another router to act as manager.
Regards.

Hi. How about your experience with Mantbox 12s? I am planning to install some equipment in a hotel zone and I would like to know if you have given good results. Greetings.

After upgrading to version 6.43.3rc my Huawey Yumo reaches a data rate of 65Mbps-20MHz / 1S. With previous versions, it only reached 54 mbps.
Thanks Mikrotik!

Hello, I had the same problema.
I solved it by disabling extension channel un channel tab.

I had a pending installation with Cap Lite but in the end I will opt for other equipment because I have the same problem.

Hello Stef84,
Did you manage to implement the installation?
What speeds do you offer customers with Cap lite?
I am thinking about installing them in a small hotel with 30 rooms and I would like to know what result they have given you.

Greetings.

Hi!
I maked a ptp with this anntenas in 10 MHz and I pass 30 mbs with nstreme. Distante 11 km.

Hello Pukkita, When I connect with the mobile the map lite shows a connection of 54 mb in tx and 72 mb in rx and I can not exceed more than 20 mb doing a test of speed.I tested it with a unify ac lite and with the Movistar router and the speed test shows 40mb more or less. It is as if for the downl...

Hello Pukkita, When I connect with the mobile the map lite shows a connection of 54 mb in tx and 72 mb in rx and I can not exceed more than 20 mb doing a test of speed.I tested it with a unify ac lite and with the Movistar router and the speed test shows 40mb more or less. It is as if for the downlo...

Nobody knows why this happens ?

I think it is not normal when access point shows me data rates 54 mbs tx and 72 mbx rx.
Does that mean that my smartphone download conects in 802.11g and upload in 802.11n ?
How is that posible ?

I have the same problema.
I have fiber 300/30 but in the speed test it shows 20 mb download and 30 mb upload.
The connection shows 54 mb tx and 72 mb rx. I have tried with wap, map lite and hap lite.

I have the same problem. I have done several tests with different smartphones in map lite, wap and groove. I have tried changing the settings several times but I get the same results.
My smartphone shows only 54 mb in reception and however shows 72 mb in transmission.

Hello,
first, you must create a new configuration profile
Then add the new profile in section provisioning as slave configuration.
All your caps must be provisioned to obtain the new configuration.

Sorry for my English !

Hello,
Have you associated vlan to an interface before ?
I'm not sure but,I think you must add the bridge in the corresponding Datapath of the vlan 600 and 700.

Hi, I tried to set the load balancing group Capsman. Use 2 access points (wap and Map Lite). My problem is the next: - When I have a computer connected Wap and another in the Map Lite does not allow me to connect a third computer to any of the access points. In the logs shows the following: mac @ in...