Found an interesting piece of information. While running iPerf tests, the download will time out during the last half of the test which drops the whole speed test. Almost like a queue or something is filling up. The weird part is we see the same issue on locations that dont run any queues.
Doing more testing, We see the issue on a CCR1009 and a RB4011. The RB4011 has 1 queue defined and the network we are testing from doesnt even use the queue. I dont believe this is a queue issue. We can't use fasttrack because of needing to throttle. No firewall rules or anything. Just simple NAT. O...
We have been having an ongoing issue with slow downloads on our Mikrotik routers. This does not seem to happen with our Cisco or Ubiquiti routers. We have simple queues setup to limit bandwidth to typically 100M/100M. Download rates are around 20M while the uploads are around 95M. CPU is between 2 a...
We have a CCR2004-1G-12S+2XS router with a Cisco SFP28-25GSR-85 SFP28 connected through a breakout cable to a Cisco Nexus9000 C93108TC-EX with a Cisco QSFP28-SR4-100G. We are unable to get a link on either the Mikrotik or Nexus. This setup works well with a 40G breakout cable on the Nexus to a 10G S...
We tried esx 6.7 but never could get actual throughput over 7Gb. Loopback testing was 61Gb. We are testing debian 10 with frrouting right now and are getting 38Gb throughput and around 25% load across all 20 cores. No core is loaded more than 30%. We much prefer the mikrotik interface but as of righ...
We are working on getting our new CHR's tuned and configured. We have used the bandwidth test to the internal loopback interface with good success. We are getting different results on testing between the 2 different CHRs. Is this to be expected? We have tried disabling VMQ, offloading, upping the qu...
We have not had any trouble in the last several releases until 6.45. We always watch the forum to see any issues that other people have before updating. I think the issue is coming from that they tried to push the 6.45.1 release out quickly cause of the cve and then tried to push this one out quickl...
Not as easy when you have a few hundred vlans. Not bad to script but would be nice to have a simple checkbox to automatically have all interfaces as passive and then add the ones you want.
Same issue just happened to us. RB4011 running OSPF, BGP and MPLS. Timeout while waiting for program filled the logs, random numbers. Also error dhcp1: failed to give out IP address: unknown pool mixed in. Reboot resolved the issue. BGP is offering default routes only, OSPF is providing 202 routes. ...
We tried that and no change in ccq. We changed from nv2 to nstream and we are currently running at 99% ccq. Signal level dropped to around 57. This link is rocking now. Currently ordering more netmetals to replace more links.
Unfortunatly Mikrotik does not have OIDs for BGP. We use LibreNMS for monitoring and was able to use the nagios plugins and the Mikrotik BGP plugin from here https://github.com/ohitz/mikrotik-tools Works pretty well.
We actually just replaced our AirfiberX with the Mikrotiks. Getting double the bandwidth currently. We have heard that version 2 is alot better than version 1 but after the issues with the link we are reluctant to spend that kind of money if the Mikrotiks perform well. Signal on the Airfiber was -73...
We have setup a 34km link, signals are bouncing around between -65 and -48dBm. CCQ is running between 40 and 64%. We dont see much in the way of interference. Anyone have any ideas on how to tune this link? We spent around a couple of hours finely tuning the alignment. Both radios are a NetMetal 5SH...
We are not running eBGP as of yet but I will post numbers as soon as we get this implemented.
Your getting better performance with Hyper-V? I have heard others talk about better performance with ESXi. We could go either way. I'll post back numbers.
We will be assigning a couple of our ESX licenses for this. We like the idea of running 2 physical servers instead of 1 just in case of hardware failure. We are currently running a couple CCR1072's but we have not brought up our second 10Gb trunk up yet or received full routes from either carrier.
We are working on new replacement routers for our core network. We will have 2 independent 10Gb peers and full tables from each. What would be a good low cost server to run CHR on? I will admit that I have not been in the server field for several years and I am almost lost on all the new options. We...
Had another outage last night that spiked the CPUs on the CCR1072 core to 100%. We disabled BFD on all OSPF and BGP links. Hoping that doesn't happen again. The one test link stayed connected but could not route since the CPUs was maxed.
We have a central core and several border routers that randomly go offline. We have noticed that all OSPF connections report down at the same time. We have 1 big MPLS circuit connecting everything together but we created a VLAN per site (currently 28 sites but planning on adding another 20) and setu...
Thanks for that link. That is something we are watching. We will have rough 20 PPPoE connections max per edge router. With over 100 edge routers, this is why we dont want to dedicate a subnet per site. Instead we want to use the /32. It would be nice if the Mikrotiks had PPPoE Relay like the Ubiquit...
I am trying to create a script that when a client connects through PPPoE, their remote address is added to BGP networks. I created a ppp profile and added the following scripts to it but they never seem to get called. On Up /routing bgp network add network=$remote-address/32 synchronize=no On Down r...
How well would the RB450Gx4 perform with MPLS/OSPF/iBPG? We are looking at using these for our edge devices. We are setting up a full MPLS backbone using OSPF internally and then using iBGP to route public addresses. The only other thing it might be doing is NAT. Expected throughput will be up to 20...
After help from /u/Dankleton, we changed the MPLS MTU to 2020, l2mtu to 2024 and IP MTU to 2000. This helped but we have discovered that the hardware in the CRS112 is not up to the task of running MPLS at all. The CPU will peg 100% when trying to push more than 100Mb. We went with these since we nee...
Could we get a sanity check on our config? We have our Core router CCR1072 with a 10Gb uplink to the internet (sfp-sfpplus1 vlan 803) . We have a 1GB fiber connection from the Core router (sfp-sfpplus3 vlan 3000) to SW1 CRS112 (ether1 vlan 3000). We then have a wireless Ubiquiti rocket AC lite link ...
This may be my tired brain thinking way too hard and not seeing things clearly. I am wondering if I could setup a VPLS tunnel between the 2 core routers and run VRRP between them. Maybe a really bad idea, lol cant think. Headed to bed.
Sorry about that. I meant to put in more detail but had a quick service call come up. We want all our traffic to go out upstream 1 with the public IP addresses. If we lose upstream 1 or any back hauls running to it we want the tunnel to fail over to upstream 2 on the other side of the network and us...
We are working on a new design for our wireless network. We are working on converting our backhauls over to MPLS/OSPF and a meshed design. This works great for failover internally. The biggest hurdle we have is the design of the failover of our upstream providers. We have 2 upstream links, one on ea...
We got hit with that too on a test router. I took a backup of it before I wiped and updated the firmware. The funny part was we had firmware 6.41.3 on ours and that was only 2 months behind. /ip firewall filter add action=tarpit chain=input comment="Add you ip addess to allow-ip in Address List...
I set the source interface to the loopback and that fixed the peering issue. Setting syncronize=no fixed the router advertisement. I went through the second presentation and will watch the first one tomorrow. Thanks for the help.
I am working on a new design for our WISP. We currently have around 800 customers and around 50 towers. We are getting ready to order 2 Mikrotik CCR1072's for our core routers and upgrade from a bridged network to MPLS. Our needs are as follows Clients get a static NATed IPv4 address or static Publi...
I would vote to have a simple router to use at a residents house that had an ATA built-in. This way we don't have multiple devices to support and manage. It would be really nice if this ATA would connect to our current 3CX system. We service a couple thousand clients that don't have cell service an...
I would vote to have a simple router to use at a residents house that had an ATA built-in. This way we don't have multiple devices to support and manage. It would be really nice if this ATA would connect to our current 3CX system. We service a couple thousand clients that don't have cell service and...
This is what worked on the Mikrotik /interface ethernet set [ find default-name=combo1 ] mtu=1526 /interface vlan add interface=combo1 mtu=1526 name=vlan205 vlan-id=205 /routing ospf instance set [ find default=yes ] router-id=192.168.205.31 /ip address add address=192.168.205.31/24 interface=vlan20...
I didn't think of that since in the GUI it added one dynamically. I added it but still don't see any neighbors. /interface ethernet set [ find default-name=combo1 ] mtu=1526 /interface vlan add interface=ether1 name="vlan101 - BLD1" vlan-id=101 add interface=combo1 mtu=1526 name="vlan...
We currently have an OSPF network between our main Cisco switch and several EdgeRouters. We are trying to add a Mikrotik router to the mix but so far are unable to get it to see the rest of the OSPF network. Configs are pasted below. Cisco interface Vlan205 mtu 1526 ip address 192.168.205.1 255.255....
I am new to wireless bridges and wanted a sanity check on the following configuration. I am not sure about the MTU sizes or any other setting to get the best through put on our wireless bridge. Speedtest only shows around 30Mbps. At the AP side, I can pull 750Mbps directly plugged in. [admin@PlainVi...
The above rule did not work but I think we was on the right track. We ended up dedicating a public IP address per building and everything started working. Thanks for the help.
We manage several apartment complexes and we have installed a Mikrotik CCR1016-12G router at our newest one. We have around 200 units and 5 public IP addresses. We are working with the apartment complex trying to get more public addresses. We have the issue that online gaming is not working. This wa...