Community discussions

MikroTik App

Search found 7 matches

by timking
Tue May 26, 2020 5:18 pm
Forum: General
Topic: VLAN bridges
Replies: 1
Views: 502

VLAN bridges

I have two subnets A and B, with addresses 10.1.1.X and 10.1.2.X. Router R1 routes between them via eth0 and eth1 and all traffic is untagged. Now I want to have a single VLAN99 that includes some nodes in A and some in B. So I make a bridge with only LANID 99 allowed through it and make eth0 and et...
by timking
Fri Oct 20, 2017 8:37 pm
Forum: Announcements
Topic: Wireless link calculator updated
Replies: 71
Views: 46333

Re: Wireless link calculator updated

Nice tool - but I don't understand why the power goes up as the required speed goes down. Take 2 SXT sa 3km apart, and at 6Mbps power is 31dbm and for 150Mbp it's 27dbm. Is this the power setting needed at the radio? Not very helpful when we most of us are limited by country EIRP rules. Could we hav...
by timking
Mon May 29, 2017 3:57 pm
Forum: Announcements
Topic: v6.40rc [release candidate] is released!
Replies: 231
Views: 53607

Re: v6.40rc [release candidate] is released!

Have emailed suppport but cannot set scan-list in /interface wireless to a bespoke value if you set it to eg bandb it actually sets it to bandb;bandb and then the radio stops working.
Can't set it in webfig either. Tools/telnet in webfig also broken.
by timking
Wed Feb 22, 2017 1:50 pm
Forum: General
Topic: Using ssh or winbox after setting with webfig
Replies: 0
Views: 390

Using ssh or winbox after setting with webfig

If I set everything up with webfig on a new box and then use winbox or ssh then it doesn't know I have already set it up and I get two choices: zap the entire config or set it to a default I don't want. How can I tell it to leave everything alone? There must be some flag set because winbox doesn't a...
by timking
Mon Jan 16, 2017 7:22 pm
Forum: Wireless Networking
Topic: rtsp and bridges with multipoint radios
Replies: 1
Views: 846

rtsp and bridges with multipoint radios

I was trying to make part of my network resilient using L2 routing. I have point A connected to point B (a PtMP radio) and hence through several hops to Z. A is also connected to PtMP radio C and hence to Z by a different route. I was thinking that this would make a redundant route for A to Z. All c...
by timking
Tue Nov 08, 2016 2:56 pm
Forum: General
Topic: Multiple EOIP tunnels
Replies: 0
Views: 716

Multiple EOIP tunnels

I have a network of around 60 SXTs, and many of them used as routers are set up for convenience to have the 192.168.88.x IP range as their internal addresses. I manage all the SXTs via 192.168.2.X addresses, and winbox neighbour discovery works fine using L2. Now I have three further SXTs that are c...
by timking
Fri Feb 12, 2016 5:09 pm
Forum: Beginner Basics
Topic: How to use Quick Set with dual radio?
Replies: 1
Views: 469

How to use Quick Set with dual radio?

I have just got a SXT Lite5 ac and it's got a 2.4 radio as well as a 5. Not sure why the 2.4 is useful, but the QuickSet system seems to only setup 2.4, and I can't see how to make it select the other (main) radio.

Any suggestions as to what I'm missing?