Hi there, I have been trying to test my CCR1009 connected to a 2Gbit fiber connection and I have tried both servers listed in this thread. I can consistently get 2GB's down (about 2.1-2.3 actually), but never really more than 1Gb up. Is there something I am doing wrong? I had the ISP come test, and...
olkitu Re: ...Maybe need get up also similar speedtest server here for testing... So you thinking about setting up a public btest server ? I suspect it would be very useful to all Mikrotik admins - especially near your part of the world. North Idaho Tom Jones Yeah it's nice but let see when i have ...
Hi, I'm a little further now. Situation now. CAPsMAN configured and direct connect 1 CAP it is working. But I have also sites that are PtP connected or PTMP connected I have done this with WDS CAPsMAP is working over this links but the clients don't get IP addresses. I use Local forwarding. What is...
If you use Capsman forwarding it use tunnel to Capsman controller so capsman controller should have VLAN configured correctly. With local forwarding you need configure to all AP VLAN settings. Yes, you should add management VLAN to all AP so easier manage and IP-address. Yes add VLAN id and interfac...
Please post your all configuration. Seems very strange. Do you have DHCP configured correctly or ARP issue? Try clear ARP on Mikrotik router so then you can ping?
Client get IP address from DHCP? Can client 2 ping to client 1???
There have everything: http://wiki.mikrotik.com/wiki/Manual:CAPsMAN You can make custom configuration what only allow N / AC, example 2.4Ghz configuration only N and 5Ghz only AC. If you use Capsman forwarding you do not need set up VLAN's to AP device. Capsman make own forwading default so it tunne...
Please make some picture on your network setup so it's easier figure how your network should working. Okay i try figure how this shoud working, example: Site A - B connected with Ethernet cable, A (ether1) to B (ether2 what is also bridge1). Site B connected via ether1 to DSL modem ethernet port? Si...
Thanks for the info, unfortunately the linked page asks me to "install multicast-6.24rc4-mipsbe.npk into the RouterOS operating system RouterOS#P.C3.A4ivitt.C3.A4minen following these instructions" which is a Finnish page that doesn't translate. Does that second page just tell me now to i...
Mikrotik RB3011 i have max speed about 500Mbps over NAT... hAP AC what i have, max speed 300Mbps i get. I think cannot get over 1200Mbps, (only 1G port, so max speed is 1Gbps)... But look your Mikrotik CPU when testing speed, if 100%, try remove firewall rules... Do you have device what support 1300...
Using PPP connection such PPTP / L2TP / SSTP, you do not get Default GW IP Address. PPP connection use's /32 mask, there is no more available IP address. All connection normally routing to VPN gateway. It's good use different IP area than local network because then you have maybe routing issue. Plea...
Do you have correct IP address on your PC and connected to router (ether2)? Can you ping your router from computer? If you can't, you can reset your router to default settings and then get connection to router. Router should by default have DHCP Server enabled and you get 192.168.88.254 IP. Router I...
Is it possible to configure a hybrid port on the RB3011 with the switch chip? I am still trying to get an official response from MikroTik about this. You mean trunk? Multiple VLAN to one Ethernet port. Yes it's possible but devices must support that. Well... i think take time getting official resp...
Here is manual how to connect Windows and Linux to OpenVPN. You must create .ovpn config file where have connection settings. That setting use to connect to your OpenVPN Server (Mikrotik)
Add ETH1, ETH2, ETH3 to same bridge what you like get public IP...First remove master / slave on ETH2-ETH3. Other port what you want use NAT, working normally.
Please post network image what you like do... I do not get full picture your network...
If you want block some service please block all protocol and port connect to dst-address (phipson servers). I do not understand why you block only one VPN Service. I think it very difficult block because service uses multiple IP-address pool.
I've found out about MikroTik routers a bit less than a year ago. It was pleasant surprised that MikroTik is Latvian (local for me) company. So I decided to update my home network and buy one of Mikrotik routers. Now I have old version of TL-WR1043ND router, which can handle about 104 Mbit/s max by...
I have issue on my hAP AC. I got max speed with wireless 10Mbps download and 50Mbps upload. Handshake speed with AP and my laptop is 780Mbps. With cable, speed is 1Gbps. I tried reset my reset, reconfigure it... Changing channel... Changing RoS version... CPU 4-5% max, no firewall / queue rule. Also...