MikroTik

Currently not possible, but this in our to do list.
Any updates?

Very close to final version.

interface/lte/show-capabilities [find]

Good.

Should be fixed now

Any thoughts on the phy rate dropping down and then going back up after hitting align? Beamforming happens on first minutes, data is updated only on those events for stability reasons. Align causes device to disconnect and sporadically run beamforming with high update interval - updating actual con...

On Cube PRO devices data is gathered during beamforming events, if there hasn't been beamforming event - it will use less reliable data for calculation, this is less reliable distance assumption that was used for older (wAP,LHG, nRAY series)

I bought 8 960's. Two are in the Ampere and six in the RDS.

i have same hardware, i will check whats going on, on RDS test seems to be correct and provides expected results.

If these PM963 drives are capable of up to 1800-2000MB/s (14-16Gbps) with 4 PCIe lanes, that means that I should see roughly 7-8Gbps in straight reads from one drive with 2 lanes on the RDS2216. You should be able to get 12-16Gbps on RDS - PCIe connection is just to NVMe controller, not memory chip...

i haven't used VNstat, just citing dockerhub page - vnStat is a network traffic monitor that uses the network interface statistics provided by the kernel as information source. so it looks to me that it monitors local network devices. Container runs on RouterOS kernel, BUT only veth interface contai...

I ran a disk test from the Ampere ROS 7 to the RDS2216, with two disks exported. The results are exactly half of what I get when running it locally. Increase thread-count to give device more parallel streams, each stream is single core bond. i just tried testing from container to store - with 6 dis...

Just a quick note on the short bursts: those are most likely hitting cached data rather than reflecting sustained transfer speeds from storage to user space. /disk test utility clears caches before running tests. The NVMe-TCP throughput is actually pretty impressive with the 100G interfaces and a p...

you are monitoring only virtual veth interface container is siting on. from vnstat dockerhub page: --network=host is necessary for accessing the network interfaces of the Docker host instead of being limited to monitoring the container specific interface this is currently unsupported in MikroTik con...

disk test provides similar functionality as dd utility in linux. when testing locally CPU may be a bit capped due to generation of data (random or zeroes) with 6 nvme disks (entry level U.2/U.3 drives Micron_7400 - 960GB): /disk test nvme1,nvme2,nvme3,nvme4,nvme5,nvme6 block-size=4K direction=read t...

container veth interfaces can be bridged with other interfaces

Looks like its loaded in config-less mode, apn settings from RouterOS will be ignored in this case - configure it through http://192.168.8.1
or change /interface lte settings set mode=mbim and try to load it in mbim mode.

15mm is different part number:
https://www.microncpg.com/content/dam/m ... _brief.pdf

look for CB part for 7mm
MTFDKCB7T6TDZ 7.6TB
MTFDKCB3T8TDZ 3.8TB
MTFDKCB1T9TDZ 1.9TB

U.2 disks generally starts from 960GB there are plenty of 7mm options available: https://help.mikrotik.com/docs/spaces/ROS/pages/13500447/Peripherals#Peripherals-U.2disksforRDS u.3 are also backwards compatible untested, but size compatible: Micron 7450 series Transcend TS4TUTE210T m.2 nvme inside m...

Which is not listed in the brochure, let alone on the dimensions drawing ...
https://cdn.mikrotik.com/web-assets/pro ... 190516.pdf
https://cdn.mikrotik.com/web-assets/pro ... 221150.pdf

Thanks for pointing this out - it will be fixed.

it is compatible, there is "tube" attachment included
https://cdn.mikrotik.com/web-assets/rb_ ... hi_res.png

USB dongles cant be passed to containers at the moment.
But this feature will be added very soon.

original part is -
DC Brushless Fan 40x28 12V (0.28A) 2ball (18.6CFM) 13000RPM 46dBA 70kh 150mm wire + 2.54mm 4pin
PIA040H12H-P17-AB

When considering replacing with Noctua fans - they are quieter, but usually due to lower CFM ratings.

if its for RBSXTG-5HPacD -
this capacitor is more for input voltage stability - it is not a critical part.
200V 10nF 1206,
if its significantly higher capacity - PoE may not work properly

this is control channel width - set it to 20MHz, Use Extension Channel down below to set extension length -
For example Ce - will be control+extension(20MHz+20MHz)
Ceee - will be Control+extension+extension+extension (20+20+20+20 = total 80MHz bandwidth)

just checked again with simple app - you will require a lot out of /usr/lib/python modules. my docker file ballooned up to 27.2MB FROM alpine as builder RUN apk add --no-cache python3~=3.12 curl WORKDIR /usr/lib/python3.12 RUN python -m compileall -o 2 . RUN find . -name "*.cpython-*.opt-2.pyc&...

it was 8.5MB if im not wrong, pip will add a lot of size, copy pymodbus paho-mqtt to container without pip

those seems to work: https://github.com/CrafterKolyan/tiny-python-docker-image for arm64 or arm32 you will have to change musl copy directories. my dockerfile looked like this: FROM alpine as builder RUN apk add --no-cache python3~=3.12 WORKDIR /usr/lib/python3.12 RUN python -m compileall -o 2 . RUN...

Disk is not recognized of file system is not mountable on your system?

I have the same problem.

You have completely different problem, please make separate topic

https://help.mikrotik.com/docs/spaces/R ... etervalues

You will have to print, else buffer to pick number out of - does not exist. Or use different access methods - ID, name or comment

That's interesting.. I was assuming some type of X11 terminal app.
What's it running on x86?

this is running on arm64 5009

This is still raw, but may give some ideas for some people - for example running DOOM :) /container/config/set registry-url=https://ghcr.io /container/add remote-image=linuxserver/baseimage-kasmvnc:alpine320 root-dir=your_root_dir interface=veth1 logging=yes then start your container: /container sta...

We have added possibility to write swap to external drive, in some cases this may help with OOM

CCR2004-1G-2XS-PCIe by default comes with SFP28-1 and SFP28-2 physical ports configured as pass-through to ether-pcie1 and ether-pcie2. Card also makes two extra pcie ports to host - ether-pcie3 and ether-pcie4. When inserted in Linux host it will make 4 network interfaces of which first two are lin...

possibility to attach serial devices to containers are in our TO DO list

Veth will be running when container will be running.

Check:

/disk print

is storage device called disk1?

https://help.mikrotik.com/docs/display/ ... cteristics

If we measure Watt/link distance in m, the Wap comes then out as highly inefficient when compared to the Cube. Distances increase are achieved by using passive antenna parts - "longer distance" CUBE devices uses dielectric lenses, LHG series uses prime focus dish antenna, nRAY sub-reflect...

Each device is 10 W, power is PoE only.

keep in mind that that is consumption under full load - fully saturated all interfaces wifi,60GHz and Ethernet, if 5GHz wireless is disabled consumption is equal.

Is shielded cable going to outside device?

Ethernet shield is isolated from main body.
To protect outside device you can use:
https://mikrotik.com/product/rbgesp
to protect L009:
https://mikrotik.com/product/gesp_poe_in

Does the L23UGSR-5HaxD2HaxD have support for any 802.11ad/ay/wigig 60GHz minipcie cards?

No, we have separate 60GHz product line.

You may run into problems in future due to different disk block sizes.
Reinstall would be more safe solution (when version is released).

Re-installation will be required

I would say it is a bug in Hetzner VM installation procedure, on x86 it automatically extends file system for given image to full HDD size, on ARM is does not so you have to do it manually...

This was a RouterOS bug, and will be fixed in next version. Resize was 1/4 from actual size

You are overthinking.
If you want pingable container just add extra ip address from same subnet in container manually. Ping that address

you can use scheduler for this

/system scheduler
add name=schedule3 on-event="/container print;\r\
    \n:delay 1\r\
    \n/container start number=0"  start-time=startup

there was one major change that may possible cause this, is it possible to reformat drive using latest versions and recreate everything from scratch?

from which version did you upgrade?
is this arm64 device?

Only active antenna - 3v3

Im running MariaDB together with PhotoPrism and Caddy for https proxy on RB5009 I installer MariaDB: set up envs: /container envs add key=MARIADB_AUTO_UPGRADE name=mariadb2 value=1 add key=MARIADB_INITDB_SKIP_TZINFO name=mariadb2 value=1 add key=MARIADB_DATABASE name=mariadb2 value=database add key=...

we are looking into adding swap and other features, but keep in mind that this is not docker running on RouterOS, not all options can be added that easily.

So there definitely _is_ an issue with USB disks on hAP ax^3 in 7.14rc1.

Could you please reach out to me through support system? I cant recreate disk disappear issue. I will also give you modified version with different formatting tools, that will fix other mentioned problems.

v7.14rc1 (firmware v7.14rc1) on hAP ax^3 - USB disk handling is totally broken. Also, when displaying properties, the UUID of the partition changes while looking at it - a phenomenon that should never occur. I double checked the USB disk in my laptop and it's perfectly okay, got another one with th...

viewtopic.php?t=187595

Hi,
could it be that board at some point has received more voltage than rated 11-28 V ? (For example used in automotive, where at car startup it got voltage spike)
Please check if there is stable 3v3 on port, if not U401 may be damaged.

-p flag in docker maps ports in similar way as dst-nat does in MikroTik. Container should not care about -p parameter, as it's done on network layer above it.

Could you please give more information about exact V7 version you are using?
Are you using CD image or install image?

https://help.mikrotik.com/docs/display/UM/RBM33G

FB1 CB04YTYH800 Viking Tech Corporation Ferrite Bead 80 Ohm 3A 1204

pic-selected-231031-0952-07.png

Sometimes veth can be lost automatically.

please explain this in more detail, and if possible provide steps how to repeat this, as i haven't seen such issue.

Could you please check with different USB drive?

Should be fixed in upcoming beta versions.
There is still bug that addresses may be lost on interface name change, but this will be fixed in future releases as well.

All linuxserver images do funky stuff with permission change: https://github.com/linuxserver/docker-baseimage-alpine/blob/master/root/etc/s6-overlay/s6-rc.d/init-adduser/run we are remapping users and setting folder permissions on startup, this would not always work correctly with linxuserver image ...

Mounts should work on both containers

Hello, if you are using linuxserver image - there are some steps where folder ownership is changed and Syncthing is ran under abc user. if you set PUID and PGID to 0 - everything will run as root, and you should have folder permissions. We will check why setting correct folder ownership fails. step ...

I have some luck of getting X11 Openbox menus working by using https://github.com/linuxserver/docker-baseimage-kasmvnc so X11 is possible, but there are some permission errors that has to be debugged before other apps could be accessed using this method. I don't get why would anyone use "instal...

i wish if i can do that with laptop

You can. Configure it as regular wireguard on PC.

Can you please provide some instructions how to add dual-stack IPv4+IPv6 address to a container?
Thanks
dksoft

Done! Look under Tips and Tricks section.

Please, follow the steps below, then restart a container to reproduce error log messages we get.

Thanks, we will look into this.

does not seem like veth bug to me - this is container that answers, that such entry is already in place.

next beta will have ipv6 support for veth:

add address=172.17.0.3/16,fd8d:5ad2:24:2::2/64 gateway=172.17.0.1 gateway6=fd8d:5ad2:24:2::1

as well as multiple addresses

RBM33G m.2 slot has only PCIe connectivity. Most modems are USB peripherals, it will be hard to find supported modem with PCI connectivity with correct m-key, we have some PCI modem support in RouterOS, but it would much easier to use mPCIe or USB slot for modem.

it works as regular wireguard client - PCs can use existing wireguard clients to connect.

GPS data precision can be further improved by using smoothing techniques from raw data - for example Kalman filter:
https://en.wikipedia.org/wiki/Kalman_filter
GPS output You are seeing in RouterOS is just calculated from NMEA output without any filters applied.

connect adapter to router, generate supout.rif file and send it to support@mikrotik.com with brief explanation. After that we can add it to RouterOS

@moly

what is AP used in this setup? all devices upgraded to 7.11beta2?
Could you please monitor signal levels for each station as well?

we have retested 5009 - USB specification will change to 1.5A

We will have additional fixes for 802.11ay devices in upcoming beta versions.

mostly container and rose tests - some heavy writes after that no use at all.

p.s. Just checked 5009 - it seems that inner power delivery circuit should support 1.5A, we will recheck if there is a mistake in spec sheet.

I personally have been using 1.7A rated Micron 5200 SSD via USB to SATA close to year with RB5009 - no issues so far.

system/routerboard/usb/power-reset duration=5

will reset USB power for 5 seconds.
you can use this in scripts to do power reset at 50GB mark.

Currently not possible, but this in our to do list.

sorry it's bit hard to understand your question, but my guess would be that you are doing btest from router to it's own IP address. In such case traffic is not leaving router.

what would be the use case for such limitation?

Could we please get a bit more feedback before we include this fix in upcoming stable version? Thanks!

path issues should be fixed in latest beta versions

container is not a virtual machine, do not use it as one.

is root-dir also pointing to usb drive?

Yes fixes will come with 7.10 branch - otherwise it will slow down existing 7.9 development.

I tried building with your Dockerfile, but unfortunately build time outs during bundle install for me. quick guess is that some PATH variable may be missing, could you please check if this works with: container/envs/add key="PATH" value="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/b...

Now hello-world should work. Thanks @dynek and @tangent for helping solving this. Fix will be included in upcoming beta version.

beta will be released immediately after stable release. Probably next week.

@dynek we found what is causing this and we will try to address this in upcoming versions.

Are you seriously? containers are broken, but there is no fix. importing remote image: adguard/adguardhome, tag: latest was unable to import, container 71e2cc5c-abf7-415c-b63a-45036240aa61 not "containers", but particular ones imported that are OCI schema based. This is due to change in d...

previously mentioned cards were tested on bare x86 installation, if you can send exact hypervisor used and steps taken to support@mikrotik.com i can take a look.

Mellanox and Chelsio adapters work with v7.
I have personally tested Mellanox CX516A and CX515A as well as Chelsio T62100-SO-CR
others should work as well. Keep in mind that only Ethernet mode is supported, if adapter is in Infiband mode, it has to be "switched" to Ethernet mode beforehand.

If this is Intel 100HFA016LS or other similar Intel OmniPath - this card supports OmniPath only - no support for Ethernet at all. This card will not be supported in RouterOS.

Hello, fix hopefully will come with next beta release.

Next beta (after RC and stable) release, should address some of x3 issues as well. Hopefully mdmg-fix could be switched to off onward.

Fix should improve stability to 802.11ad line as well. Unfortunately we will not have it ready to next stable release cycle.

We have potential fix for PtMP issues. We are still testing, but it should be ready in next beta releases.

Thanks! Well, I hope that a new release is coming soon, at least as a beta!

Fix is included in upcoming beta

Thanks for report. This is known issue - automatically "servers" field is passed to container, but in case of DOH this field does not exist, for quick fix set/change DNS in container setup to Routers DNS IP address -
/container/set <your container> dns=192.168.88.1

NVME-tcp has nothing to do with physical NVME disks. Target can be USB drive, NVME drive, SATA drive or even part of RAM on the device. Same goes for iSCSI and all other mentioned protocols. ARM based RB1100Dx4 Dude edition supports 4 SATA drives, making it a good candidate for ROSE package testing ...

is it possible to get supout.rif files from this case? Please send it to support@mikrotik.com with reference to this thread.

ROSE-MANAGER still cannot mount iscsi devices from QNAP/Synology NAS to CHR: Thanks we will check this Can you please advice how to rename the disk? I habe usb1 or nvme1 and if I change the name, the error "can not change device type (6)" appears. thanks, this is Winbox bug, should work f...

thanks for reporting this, we will check how to fix this in upcoming versions

USB Gb ethernet adapter (Techole UH411) with Realtek RTL8153

This chipset was never fully supported. we will check if we can add it properly.

What is the reason for that slow transfer?

SFTP is slow single connection protocol, run multiple instances parallel to get faster results.
For rsync - please read rose manual page.

@rameex43
make raid1 with tcp-nvme drives

@Babujnik
Thanks we will try to fix this.

@sirbryan
Simple partitioning will be available in upcoming versions. We will check what we can do about LVM or ZFS.

@issme
RDMA is different beast, currently its not planned.

Feel free to suggest other protocols and features that should be supported.

The rose-storage module also has command additions in /file/sync.
However that is completely undocumented and not so easy to figure out...

this is rsync, i will add documentation tomorrow for this

please comment ROSE package in designated topic viewtopic.php?t=192888

Hello,

please fix this (SUP-104510) . Thank you

this issue is not related to new ROSE package. SMB in ROSE package currently will only support SMB2.1 SMB3.0, SMB3.1.1 dialects

macOS fix for SMB will be available in next release

simple "/" should work as path. Currently nfs/smb is applied to disk. If only exact folder is required on client side - use "slot/folder"
f.e. on linux initiator:
sudo mount -t nfs 10.155.166.7:/sata2/stuff /mnt/files

Windows users be aware that default built in NFS client does not support NFS v4 mode.
https://learn.microsoft.com/en-us/windo ... s-overview

maybe anyone more competent in windows systems may comment on this. Is there any good third party tools or workarounds?

What's new in 7.8beta2 (2023-Jan-20 12:27): !) storage - added new "rose-storage" package support for extended disk management and monitoring functionality (ARM, ARM64, Tile and x86) (CLI only) What's new in 7.8beta3 *) rose-storage - added support for GPT partitioning (CLI-only) *) rose-s...

mount -t nfs server:/path /mountpoint

nfs-share=...
documentation is still in progress

ROSE package includes different formatting tools, please check formatting with ROSE package enabled.

no, only power is connected to USB port for this model.

Free package, available for arm,arm64,Tile and x86

Several comments:

Thanks noted.

Nice changelog, I don't know how to find that "rose-storage" ..

documentation draft:
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

you need to install rose-storage package first

viewtopic.php?t=192810
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

So my point is if Mikrotik is going to be promoting container usage...they should try to make available on all platforms.

Please show us tools for building containers for those platforms and working example.

Thanks, this will be especially useful very soon

Edit:
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

' WD Red SA500 M.2 ' will work, any SATA m.2 should work.

we have tested drives up to 1TB, but i don't see why larger drives would not work. From software side there is nothing that blocks larger drive use.

i have already answered this question previously.
viewtopic.php?p=953660#p953567

CCR2216-1G-12XS-2XQ supports only SATA drives in M.2 form factor slot. none of mentioned NVMe drives will work. You should look for M.2 2280 SATA III. SATA III drives support up to 6Gbps As it goes for throttling - this greatly depends on use case. For light Container use - this shouldn't be noticea...

we would need step by step how this can be repeated.
For me files always stay with correct uid,gid when upgrading from 7.6 to 7.7

@elico
looks much better, newer versions (7.8 brach) will allow to change .type permissions without extra steps.

@TheNetworkBerg
Thanks for your videos! I will try to repeat upgrade issue.

fix for .type will be available in next releases.

@elico .type file inside mounts is for RouterOS to mark folder contents as not to be listed inside RouterOS. Correct fix would be not changing permissions for this file from uptime-kuma side, or allowing permission change or change the way of listing/not listing folders from RouterOS side. Deleting ...

Thanks, i just tried, and yes, there is small bug that would not allow to start this unless you do few extra steps (fix will be available soon) Setup container setup as explained in our help page (add registry url, add installation medium, set tmpdir if not enough memory on main disk) setup mounts: ...

RouterOS is not based on systemd

So what exactly is broken? Use of the RAM disk for container storage?

In this case, cause is not related to tmpfs

Thanks, I managed to repeat this issue. This was broken somewhere from stable 7.6 to rc, release. You can use 7.6 for now, as bare Openwrt uses only 8.8MB on arm64 systems / # cat /etc/banner _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_...

You can use armvirt target -

docker import https://downloads.openwrt.org/snapshots/targets/armvirt/64/openwrt-armvirt-64-default-rootfs.tar.gz openwrt-arm64
docker save openwrt-arm64 > openwrt_arm64.tar

This issue brings in problem in starting containers. All I need are to re create and do some minor configurations Please elaborate. Name(slot) does not change on previously added/formatted disks. On newly done formats slot will assume new name based on physical slot. If name was "disk1", ...

Currently I have done the test on a hAP ac3 (arm) and the same thing happens, the global variables disappear from the environment after a few minutes of closing the winbox.

Thanks, we repeated the issue

What's new in 7.7rc1 (2022-Dec-08 16:38):

*) interface - show RTL8153 CDC Modem Device as ethernet;

I can't set or get the disk name on my hap ac3.

Disks now have slot, as their name. This will be included in Winbox in future releases.

/disk set 0 slot=...

*) disk - added support for manual RAM file system (TMPFS) creation (CLI only); Great news! But this means we will not see the default behavior to change on devices that did not use a RAM file system till now? So to have consistent behavior (and paths in scripts) on all devices I create a disk of t...

You need to add the variables for your container before you pull it down: /container/envs/add key=cap-add name=MYCONTAINER value=NET_ADMIN /container/envs/add key=device name=MYCONTAINER value=/dev/net/tun Where MYCONTAINER is the name of your container. /dev/net/tun access was added in 7.5beta4 an...

Maybe it could be combined with a new feature to have RAMdisk on ALL devices with sufficient RAM (not only those with insufficient flash) and a compatible
and predictable way to store persistent and nonpersistent files?

maybe in next release

Should I expect the file system on RouterOS to go from using "disk1" to "sata1-part1" as the "root" directory name? Disks will now carry names where they are physical connected - it will make finding physical disk much easier. After formatting, there will be no issues ...

nice job! Thanks for sharing!

/dev/stdout and /dev/stderr permissions are fixed in latest beta releases (starting from 7.7beta6)

mounting files instead of folders are not yet implemented.

there will be fix for similar issue in upcoming versions.

Fix for this will be available in next upcoming versions

Is this 32bit CPU?
x86 32bit only is not supported by RouterOS v7

openssh isn't installed in ubuntu containers by default. You can use shell to access your container -

/container/print
/container/shell 0

Thank you for reporting this, we found main cause for this issue, but it will take same time until fix will be available. Currently as workaround please mount /var/log as explained by previous posters.

The same way tun/tap access was enabled in containers under RouterOS maybe access to usb devices can be enabled too, with a proper feature request.

this is in our to do list.

PCIe AHCI or PCIe NVMe ?

PCIe NVMe !

1100AHx4 had SATA drives, CCR2116-12G-4S+ uses PCIe drives

Thanks for detailed reports, we will look into it.

I tried on a RB5009 and this zabbix/zabbix-proxy-sqlite3:alpine-6.0-latest tag has linux/arm64 in it: https://hub.docker.com/layers/zabbix-proxy-sqlite3/zabbix/zabbix-proxy-sqlite3/alpine-6.0-latest/images/sha256-44a5cdd64302b2a061415a3f31a31704b8aa4a15d2c31a0ae5084d20c0271a22?context=explore remot...

I see the mounts, but I want to write to them, which is not possible (permission error).

I can't reproduce this. Please write to support with exact steps how are you getting this error and reference to this forum thread.

stop/start newly created and started container and mounts should appear. We will fully fix this in next releases.

I'd like to see IPv6 support. thanks, noted. - The CT can't write to the mounted dirs - is that normal? Is there a way to write to them or to any place that's visible on the host? I need the container to write logs and status files. mount folders are not browsable from RouterOS, but you can access ...

i think i got where it goes wrong. As a workaround currently you can after adding container start it, stop it and start again. Mounts should appear. we will try to fix this in next releases

I'm running RouterOS 7.5beta4 on my hAP ac³ and: 1- mounts still doesn't work for me; 2- I noticed that a default route is not being added to my container, even though gateway is defined in interface/veth . 1. mounts needs to be removed and created again if upgraded from version with broken mounts....

Could you allow systemd to work inside container?

NO!

That sounds good! How will it be supported?

/dev/net/tun device now is available for container use

tun/tap support will be added in next release. Anything else to consider adding before stable release?

5GHz interface is designed as backup for 0.001% of time when main 60GHz interface is unavailable. it's not designed as Access point for other wireless clients or other uses.

Mount issues should be fixed in next release. Will it be possible to add capabilities to containers? For instance, cap NET_ADMIN is required to create/use TUN/TAP virtual network devices for various functions. OpenVPN or other VPN solutions, like OpenConnect requires this functionality. currently th...

Is it fair to assume that the MT containers do not support the equivalent of Docker bridge mode networking?

And if that is correct, is future support for bridged mode on the roadmap?

how is "bridge mode" any different from current implementation?

mount issues are still not fully fixed - but we are working on this issue.
is there any more functionality we should consider adding before container goes to stable release?

My laptop is old though, nothing recent about it.. Two mPCIe ports and two other ports that I'm not using (one is another mPCIe, do not remember the fourth's form factor right now).. MC7355 is from 2012.. It had a MC7455 but it died a few years ago, so I put the MC7355 back.. Yes, it is time to loo...

is this still repeatable in v7? if yes - please contact support with supout.rif file.
information here is not all correct. Modems should be supported on all systems equally.
X86 installation is still supported.

specifying directory will be possible in next release

have you added this mount entry to container as well?

/container set 0 mounts=config

Please use main container thread for questions regarding containers.
viewtopic.php?t=178342

for lazy Bobs, there is remote-dist to dockerhub, where you can be sure that what you see is what you get.

running sshd into container is bad practice from start and is not correct use of containers all-together.

it runs for a moment (<1s) and then stops. same with debian image. in my case disk1 is an 8gb usb2 flash drive freshly formatted in winbox as ext4, but same behavior if I try to it on the device's storage are you running any command inside container? If not this is how it should behave. try runnign...

why would anyone download image from unknown source when this can be done in few minutes locally and safely and to any supported architecture? make Docker file with contents - FROM ubuntu:latest RUN \ apt-get update && \ apt-get install --no-install-recommends --yes openssh-server &&...

currently you can follow instructions b and c. Next releases will make pull directory configurable.

We repeated

sudo: effective uid is not 0, is /usr/bin/sudo on a file system with the 'nosuid' option set or an NFS file system without root privileges?

issue and found the main cause. We will check what can be done.

probably not enough memory for downloading and extracting layers. Use pre-build or pre-fetched image instead. Variant B or C in docs

Looks like all permission issues are caused by accessing previously created containers, containers are and should be isolated from each other - if same files are required for multiple containers use mounts. Do not put mount src in root-dir either. root-dir should be on external memory for now.

sudo: effective uid is not 0, is /usr/bin/sudo on a file system with the 'nosuid' option set or an NFS file system without root privileges? Please check that the disk is mounted as disk1, also check if reformatting from RouterOS helps. I have similar setup, only difference my disk is formatted with...

@bma and others, regarding container - please use other threads to discuss container in detail

set environmental variables as per docs DNSMASQ_USER should be root

Two quick questions about containers:

1) are veth interfaces mandatory, or can host networking be used?
2) the docs state that ext4 is supported, is this new? Any plans to add ext4 support to Disks > Format Drive?

1) Yes
2) Disks are formatted from RouterOS as ext4 for a while now.

CCR2004-1G-2XS-PCIe is istalled in first PCIe3.0 slot?

If there is slight rattling - this does not affect functionality, devices will work fine.
If there is part loose inside shell - return it to RMA.
Shells are welded, they are not designed to be taken apart.

next v7 beta version will have potential fix for this issue. Do you know the cause of this behaviour? We have dozen of nray link in production since months/years and only this specific link has this trouble. We even replaced both nray and tried to swap a nray by a wap60. Knowing the cause would hel...

next v7 beta version will have potential fix for this issue.

that table explains 802.11ad standard available rates.
those devices does not support MCS 5 and 9 and other MCS's are disabled to improve stability.

@antonsb is there any planning for other OS/hypervisor support, e.g. VMware ESXi 7.x ?

we will look into it

@tensioncore @pe1chl
this card currently has drivers in Linux latest Linux kernels and BSD.

@ns88ns
no bifurcation required, Linux system will see 4 network devices

5GHz antenna holder allows some play on early models - this is fixed in later revisions.
Devices can't be opened without destroying outer case.

return container support

soon! just some minor things left.

Using two PCIe cards or USB based (LTE modems) are supported, but there are some limitations. To use two LTE modems - USB lines has to be switched by removing jumper near USB port. If two pcie (wireless) cards needs to be used - there are some limitations to bus speeds that may cause performance iss...

https://mikrotik.com/product/RB435G#fndtn-downloads
Under Downloads you will find dimensions pdf that will help you to design enclosure.

you are missing http-method

judging from signal strength - your alignment is way off.

This is due low gain antenna? WHich is the difference from LHG60?
nRay and LHG 60G is supposed to be capable same link lengths. Why to lower power limit for the nRay and not for LHG 60G? How that will play out?

This power limit is active when "region=eu" is used

sure, sorry i gave v7 compatible code v6 will look like this foreach i in=([/interface wireless scan wlan1 duration=5 as-value]) do={if (($i->"ssid")="Test_Network") do={:put $i}} so what does this do: /interface wireless scan wlan1 duration=5 as-value does scan for 5 seconds and...

yes, you can in multiple different ways: 1) if you can connect to network - you can check interface status (running or not) and based on that write a script 2) if you can't connect you can check log messages when interface tries to connect, but fails 3) You can run scan and check if ssid is present ...

Search found 429 matches