/ip ipsec peer add name=some-peer exchange-mode=main address=<IP Address> /ip ipsec identity add peer=some-peer my-id=key-id:<GroupName> mode-config=request-only generate-policy=port-strict auth-method=pre-shared-key-xauth secret=<Secret> xauth-login=<UName> xauth-password=<PW> But you'll probably ...

I ask for help to configure Cisco IPsec (Mac OS terminology). As I understand it, this authentication method is called "pre shared key xauth", i have only following data:

IPSec Gateway <IP Adress>
IPSec ID <GroupName>
IPSec Secret <Secret>
Xauth Username <UName>
Xauth Password <PW>

That's moo much both for first hAP ac PoE out capacity (700mA, at 24V that's almost 17W which is max power draw of a single hAP ac) ... and for original power adapter, rated ad 1.2A which is almost 29W, less than two hAP ac units combined may draw. Okay, I will try to change the power supply of the...

I put my MTU lower (1400) for PPTP connection and it works great!

Thank you for advice!
After change MTU and MRU for L2TP connection bandwidth test is working both ways

I have chain of three HAP AC, power supply connected into only first (main) device. Second device get power by PoE from main MT. Third device get power from previous (second) device. The problem is that second and third (of course!) devices are rebooting unexpectedly. Could there be a reason not hav...

I need to simulate bad channel. I know how to drop random packet, change QoS randomly by scripts and scheduler, but i don't know how to increase RTT?
Does anybody changed RTT on RouterOS?

In my account on Mikrotik.com site, CHR section i have several 'System ID', a couple of them has 'died' (status is red). Can i delete these systems from my account?

I have several WANs interfaces and two of them have common gateway. In route list i use this gateway 1.1.1.1%eth2 - and next one 1.1.1.1%eth3 I'd like use the recursive routing but it doesn't work in my configuration (%interface). Does someone have any idea? Netwatch? The first question is what is ...

I have several WANs interfaces and two of them have common gateway. In route list i use this gateway 1.1.1.1%eth2 - and next one 1.1.1.1%eth3
I'd like use the recursive routing but it doesn't work in my configuration (%interface). Does someone have any idea? Netwatch?

I found a part of answer...
I change RP filter to strict and everything was working as before.

RP filter default is 'no'.
But how did it work before with the default setting?

I'm discouraged, please help me to understand this issue. Could i connect to the Routerboard if the forward and reverse routes are different? Example: I have RouterBoard with Dual WAN. I have route to 0.0.0.0/0 from the Gateway_ISP1 only, then i try to ping to IP_WAN1 and IP_WAN2 i get a positive re...

ISP fixed the issue.
They somewhere made a mistake when replacing their own equipment

I suppose ISP's equipment was wrong configured

Dear Experts! Explain me please what does it mean: 1. I have RB951 with a simple configuration 1WAN, NAT and L2TP to office ~ 10 users 2. In Interface i'm watching there are no traffic or a little bit working traffic ~ 1 user at office 3. Rx on WAN interface too much! 4. Torch shows traffic from unk...

Hmm can u please post here exacly where to put this code? Cause I coudn't make it work...
Actually I need UTF in body of e-mail message.

See screenshot here:

Hello all! I'have a lot of point of sale where we use the mikrotik routers. Some shops have dual WAN interfaces for failover by recursive routing. I want to monitor each of WAN interface thru ping to google DNS. How can i do that by dude? In other words, it is necessary to start the ping from the d...

Hello all! I'have a lot of point of sale where we use the mikrotik routers. Some shops have dual WAN interfaces for failover by recursive routing. I want to monitor each of WAN interface thru ping to google DNS. How can i do that by dude? In other words, it is necessary to start the ping from the d...

Hello all!

I'have a lot of point of sale where we use the mikrotik routers. Some shops have dual WAN interfaces for failover by recursive routing. I want to monitor each of WAN interface thru ping to google DNS. How can i do that by dude?

Hello, All my configs have 4 rules: accept for Connection State = established accept for Connection State = related (for input and forward chains respectively) after upgrade to latest ROS (for example 6.33.1 -> 6.37.1), I discovered that these rules now without any "Connection State" value! now its...

Code: Select all

MIME-Version: 1.0
Content-type: text/html; charset=UTF-8

Insert this under first line in subject

gmick, thank you very much. I've inserted this line below the subject it works perfect!

Some variables in notifications seem to be missing, for example :
[Service.Status]
[Service.ProblemDescription]

I have 6.37 (rc42) and some notifications have been changed:

[Service.Status] = [Device.Status]
[Service.ProblemDescription] = [DeviceType.ProblemDescription]

RouterOS does not support any encodings actually. Only A-Z and 0-9 can be used in most places.

Thanks!

I have a problem with encoding for email notification. Cyrillic symbols do not display correctly, for example notes for device. Most likely the reason is that emails are sent in us-ascii encoding, by default and i have no possibility to change it to UTF-8.