MikroTik

nemoforum

The answer from support: Hello, We have investigated and turns out there is no issue with the hAP ax² but with the SXT LTE6. If you will use hAP ax² in warm enviroment, there should not be issues with SXT LTE6 detection. I would suggest setting poe-Out to forced on to prevent this issue. Best regard...

nemoforum

Yes, waiting for an answer.

nemoforum

I was able to reproduce the issue on 7.13 and 7.11.3. Also, turning the interface off/on or switching PoE mode to force and back to auto doesn't help. The product page says “Tested ambient temperature -40°C to 50°C“. My devices have issues in the range -6..+18. Once more, the reproduction steps: 1. ...

nemoforum

Hi! I've already provided the below info to the technical support via the ticket (SUP-142024), however, it would be nice to confirm the potential (software I hope) issue. I have SXT LTE6 Kit connected to hAP ax2 ether1 PoE port. hAP ax2 is powered via a stock power adapter. I was able to reproduce t...

nemoforum

I'm observing PoE issue with hAP ax2 and SXT LTE6 kit: when ether1 on hAP ax2 is configured with PoE Out = "auto on", PoE seems to be reset (during LTE modem init ?) and SXT LTE6 kit is rebooted. This continues in a loop. SXT LTE6 kit could boot on 6 or 7 iterations successfully. Setting e...

nemoforum

kernel.org or any other source do not have any value at all. Panama is 30dBm The unique official source https://www.asep.gob.pa/?page_id=13116 Page 131 Regdb is filled up from such sources, but it could be outdated, for sure. Okay, let's take a look at https://www.asep.gob.pa/?page_id=13116 Page 13...

nemoforum

Tx Power for 2.4 GHz interface on hAP ax2 is limited to 15 dBm. Tested with different Country configured. Moreover, right after changing a country 20 dBm is displayed for a while and then it falls to 15 dBm. The monitor command will report transmitter (radio) power. As rextended pointed out, 15dBm ...

nemoforum

Tx Power for 2.4 GHz interface on hAP ax2 is limited to 15 dBm. Tested with different Country configured. Moreover, right after changing a country 20 dBm is displayed for a while and then it falls to 15 dBm. Copy & Paste??? https://forum.mikrotik.com/viewtopic.php?p=993395#p993395 Same reply: I...

nemoforum

Tx Power for 2.4 GHz interface on hAP ax2 is limited to 15 dBm. Tested with different Country configured.
Moreover, right after changing a country 20 dBm is displayed for a while and then it falls to 15 dBm.

nemoforum

Tx Power for 2.4 GHz interface on hAP ax2 is limited to 15 dBm. Tested with different Country configured.
Moreover, right after changing a country 20 dBm is displayed for a while and then it falls to 15 dBm.

nemoforum

And where

/interface/wifiwave2/info country-info

is located now?

nemoforum

>Authentication failed for any device
The same. Have to revert to 7.7beta6

nemoforum

finally https://fccid.io/TV7C53-5AXD2AXD

nemoforum

You can work around it by creating a separate network for such crap, with a separate SSID and authentication configuration. Yeah, I did that. But the interesting thing is that I can't manually configure the same behaviour that auto does: in my case, it seems, Ring cameras want TKIP enabled for some...

nemoforum

please try this : in queues -> interface queues on wireless interfaces change from wireless-default to only-hardware-queue Could you please clarify what issue this advice will potentially fix? -- Finally, I gave up waiting for ax3 and bought ax2 yesterday. First impressions are good. Finally, I've ...

nemoforum

If you have no answer - don't reply. And before replying, please, read carefully.
Mikrotik declared 24/23 dBm and FCC measured 29.3/28.4 dBm for the same device.

nemoforum

Max output power for 2 & 5 GHz respectively:
https://i.mt.lv/cdn/product_files/hAPax_220854.pdf - 24/23 dBm
https://fccid.io/TV7C52-5AXD2AXD - 29.3(853)/28.4(704) dBm(mW)
Can someone explain?

nemoforum

Perfectly works for a long time. PowerBank with PD output (20V in my case) + PD 20V trigger ( https://www.aliexpress.com/item/1005003160923563.html ) + XT60 connector + XT60 to 5.5x 2.4 cable (from Miniware TS80 Soldering ha-ha [yeah, it's not 5.5x 2.1 but it works]) + a little bit of soldering. But...

nemoforum

Does hAP ax3 really have more tx power than hAP ax2, considering that wireless chips are the same (QCN-5022)? Max output power for 2 & 5 GHz respectively: ax2: https://mikrotik.com/product/hap_ax2 - no wireless specifications https://i.mt.lv/cdn/product_files/hAPax_220854.pdf - 24/23 dBm https:/...

nemoforum

Can someone compare hAP ac2 & hAP ax2 in terms of coverage zone (bigger, smaller, same) and speed at the coverage zone edges? Thanks.

nemoforum

Does it have less output power and worse sensitivity than hAP ax3? I don't see Wireless specifications here https://mikrotik.com/product/hap_ax2, but it's in place for hAP ax3 https://mikrotik.com/product/hap_ax3 . At the same time, FCC shows up to 853 mW for 5 GHz and 704 mW for 2GHz https://fccid....

nemoforum

https://mt.lv/Chateau_5G_ax
https://mt.lv/Chateau_LTE18_ax

nemoforum

Mikrotik!
I kindly ask you to release wave2 extra packages separately for each CPU in order to fit 16MB Flash.
It is possible to run wave2 driver on 16MB Flash and 128 RAM.

nemoforum

Regarding /routing/export :

2021-02-08_22-38.png

nemoforum

Will wave2 driver support features like no_country_set, superchannel and so on? Or the new wave2 driver is provided by the vendor and there are no customisation options?

nemoforum

Got bootloop after upgrade 7.1b3 ->7.1b4 on my hAP ac2.
Had to netinstall 7.1b4 with configuration reset, then applied the backup (from 7.1b3).

nemoforum

!) added new experimental wireless package "wifiwave2" for ARM devices with more than 256 MB of RAM (CLI only); Does it mean that 802.11ax devices are coming soon? Can we expect this new wi-fi driver to replace the old one in 7.x for hAP ac2 (mine has 16M of flash and 256 of RAM)? Did you...

nemoforum

!) added new experimental wireless package "wifiwave2" for ARM devices with more than 256 MB of RAM (CLI only);

Does it mean that 802.11ax devices are coming soon?
Can we expect this new wi-fi driver to replace the old one in 7.x for hAP ac2 (mine has 16M of flash and 256 of RAM)?

nemoforum

It seems wi-fi issue has been fixed in 7.1beta3. Running it for a week without any issues.
PS: not yet available for everyone.

nemoforum

RouterOS version 7.1beta2 has been released in public "development" channel!

Can also confirm a DHCP issues on hAP ac2: wireless clients time to time are unable to get IP address and reconnect in a loop.
WLAN interface disabling/enabling temporary "fix" the problem.

nemoforum

Dear Mikrotik! I reported this bug on v7.0beta8 on 10/06/20, you confirmed it on 18/06/20 and wrote we look forward to fixing this on upcoming RouterOS versions, unfortunately . See SUP-5149. v7.0beta5 - no issue v7.0beta8 - the issue appears v7.1beta1 - not fixed v7.1beta2 - not fixed Is it so huge...

nemoforum

It looks like the issue (unable to get IP via DHCP from ISP) with vlan10-wan anchored on the bridge is related to that fact that packets from CPU are not being forwarded to the switch. I added a switch rule "copy all packets from switch1 cpu to ether1-wan" and were able to get an IP via DH...

nemoforum

Hello everyone. In the previous topic I was fiting with bridge filtering https://forum.mikrotik.com/viewtopic.php?f=2&t=158041. I was able to configure the following: VLAN-Question-2.png _ /interface ethernet set [ find default-name=ether1 ] name=ether1-wan /interface vlan add interface=ether1-w...

nemoforum

For the other way you need tagged vlan also on bridge interface, i.e. tagged=ether2,br.

This:

/interface bridge vlan
add bridge=br tagged=ether2,br untagged=ether1-wan vlan-ids=10

works! Thank you!

nemoforum

BTW, I've tried the solution suggested by Sob in this post https://forum.mikrotik.com/viewtopic.php?f=13&t=157803#p776032 : - bridge all ports together - bridge itself is your untagged LAN - give PVID 2 to bridge port ether1 - add VLAN interface with id 2 on bridge - VLAN interface is your new W...

nemoforum

Okay, I got it working with this config (using switch chip, i.e. with HW offload): /interface ethernet set [ find default-name=ether1 ] name=ether1-wan /interface vlan add interface=ether1-wan name=vlan10-wan vlan-id=10 /interface bridge add name=br protocol-mode=none /interface bridge port add brid...

nemoforum

Sob,
Thank you for your answer. It looks like exactly what I want.
And you are right, adding all interfaces to one bridge is confusing at first look.
I'll give it a try.
Thanks again!

nemoforum

Hello! Recently, I've found Manual:Layer2 misconfiguration - VLAN in bridge with a physical interface https://wiki.mikrotik.com/wiki/Manual:Layer2_misconfiguration#Bridged_VLAN_on_physical_interfaces . I have the same configuration and would like to make it better. However, the provided solution is ...

nemoforum

Hello, everyone. FYI: I already spent some time with support in ServiceDesk, the ticket number SUP-5149. I'm trying to get mark based routing working. This config (idea) was perfectly working on the latest ROS 6.xx beta. Router info: architecture-name: arm board-name: hAP ac^2 cpu-count: 4 cpu-frequ...

nemoforum

*) added support for HiDPI displays;

Finally! Thanks!
Now it looks pretty good on LInux under Wine on 4k display.

nemoforum

OnePlus 6T, Mikrotik App (latest) Force close right after start: 01-17 23:13:39.415 906 2950 I ActivityManager: START u0 {act=android.intent.action.MAIN cat=[android.intent.category.LAUNCHER] flg=0x10200000 cmp=com.mikrotik.android.tikapp/.activities.MainActivity bnds=[844,1106][1048,1443]} from uid...

nemoforum

Mikrotik App (latest from Play Store, clean install) force close right after start on OnePlus 6T (latest stable firmware).

nemoforum

Setup: server2 - ISP - ether1-wan - hAP ac2 - ether2-vlan10 - server1 With hardware offload turned off on all interfaces iperf3 speed between server1 and server2 is around 800-900 Mbps in both directions. If I turn hardware offload on, iperf3 speed server1 -> server2 drops to 280 Mbps. Server2 -> se...

nemoforum

Mikrotik where able to reproduce the issue.

nemoforum

Hello,
we will work on this problem but first we need to finetune the new wireless driver for the new hardware and then we would try to implement the fix for the old wireless hardware.
Best regards,
Uldis C.

WHEN?!

nemoforum

------ message received from MikroTik Support ------ We cannot reproduce this issue . Testing with MacBook Pro 2016 on distance 10m in an office environment with neighboring APs hAP ac^2 performs stable and reach up to 300 Mbps. ------ End of message ------ So everyone should buy MacBook Pro 2016? ...

nemoforum

yhfung,
The main difference between wAP and hAP ac2 is CPU [arcitecture]: while wAP is based on QCA9533 (well known MIPS), hAP ac2 is based on IPQ-4018 (ARM - new to Miktorik).

nemoforum

Have you got any reply from MikroTik Support?

The first valued answer since 29 March.

nemoforum

Finally! The answer from support!

Screen Shot 2018-04-12 at 17.20.48.png

wireless engineer is working

Only one?

nemoforum

yhfung , Thank you. I'm facing the same: bad speed LAN -> WLAN5 (download) and good speed WLAN5 -> LAN (upload). Keep in mind that iperf3 client is sending by default. If you run iperf3 in client mode on your laptop you have to specify -R option in order to measure download speed (server send).

nemoforum

yhfung,
Could you please also make LAN(eth) <-> WLAN tests, as I did in another topic. Thanks!

nemoforum

So, it is a LAN-WAN routing issue. Can I confirm with all on here who have posted data across the WAN interface:

Nope, pls check viewtopic.php?f=2&t=132576

nemoforum

Has anyone sent email to support? What was the answer? Ha-ha-ha! Mikrotik's support is the worst one I've ever contacted! I contacted Mikrotik via email on 29 March. Some of the answers: For faster support we suggest to contact the company, where you bought the device. As initial/main support is pr...

nemoforum

Intel ac 8260 - the same issue.
Intel ac 7260 - the same issue.

Mikrotik?

nemoforum

Intel ac 8260 - the same issue.

Mikrotik?

nemoforum

Mikrotik,

Any official answer?

nemoforum

All those tests are made with the same wireless frequency? Another tests with different frequencies: https://forum.mikrotik.com/viewtopic.php?f=2&t=132576#p652089 As required here: https://forum.mikrotik.com/viewtopic.php?f=2&t=132576#p652015 There are NO ANY OTHER 5 GHz network neighbors!

nemoforum

Hey Mikrotik!

WHEN will this issue be fixed?
Or should I initiate a refund process?

nemoforum

Intel 7260 slow - ha-ha! It works perfectly with hAP ac (I got stable 200..220 Mbps with it) and many other routers. As well as Xiaomi Redmi Note 3 works perfectly with hAP ac (on 5GHz). The test results you asked for are below, as expected nothing changed. Also, please check this link https://forum...

nemoforum

Hey Mikrotik! Any answer?

nemoforum

The same tests with my phone and server. Screenshot_Magic_iPerf_20180401-234131.png Screenshot_Speedtest_20180401-234200.png Screenshot_JuiceSSH_20180401-234245.png Upload speed from server is lower, because vlan is configured for internet connection, BTW why so slow? With default ROS config speed i...

nemoforum

1. 2018040123023924E9.png 2. 20180401230345e6d5.png 3. 20180401230657q4A0.png 4. http://www.speedtest.net/result/7182653292 and http://www.speedtest.net/result/a/3792054297 , see 1st post 5. Intel AC-7260, Xiaomi Redmi Note 3 Pro ( http://www.speedtest.net/result/a/3792054297 ) 6. 6.42rc52 It's not ...

nemoforum

This issue is related to the chipset incompatibility between what we use in our devices, and the chip in these phones. There isn't much we can do. Newer devices, such as hAPac^2 and cAPac do not have this issue anymore. Okay, I followed your recommendation and got another issue https://forum.mikrot...

nemoforum

@normis,
Any solution?
Should I return the router?

nemoforum

I've bought hAP ac^2, configured it and got an issue: transferring speed from LAN device (micro server with 1 Gbps eth) to Wi-Fi 5GHz device is VERY low and unstable: 0.5..2..5..20..50 Mbps, tested with two 5GHz devices with iperf3. At the same time transferring speed from LAN device to Wi-Fi 2.4GHz...

nemoforum

It's really annoying!
When I'm trying to watch some video from the LAN with average bit-rate 6 Mbps, Wi-Fi connection stacked around 4 Mbps - impossible to watch continuously paused and interrupted video.
Please, help.

nemoforum

Hello! I'm experiencing some speed issue with my RB962UiGS-5HacT2HnT and Xiaomi Redmi note 3 Pro (Qualcomm) on 5GHz band. Channel speed is fine and stable, however real transferring speed vary from ~200 Mbps to ~4 Mbps. I've tested it between 2 devices connected to the router via LAN (GbE) and phone...

Search found 67 matches