I have same problem. My PoE out died in port 10

I have already writed: R11e-5HacD use too much power on miniPCIe soket for RB912UAG-2HPnD or 912UAG-5HPnD I have exactly same setup and same problem as well on 2 sets. Since this info about not using this card on this RB is not written anywhere, it is Mikrotik fault which should be fixed. Setting o...

I have the same issue with Win8.1 x64 using atheros AR9382 with latest drivers from atheros.cz. This notebook cannot connect to my rb2011uas-2hnd-in using the same security profile as in post above. This is a shame as I have no issue connectin to number of other APs, including some other mikrotik AP...

cannot find DHCP snooping function. You can use filters to block ip and mac addresses you want to. Dhcp snooping is nothing else. Well, can you please provide some hints how to implement full and proper DHCP snooping with ROS? That is, to bind MAC, IP and port in regards to DHCP leases and prevent ...

RB600 + RB654 + v6.5 results in non working LAN ports on the RB654

Any update regarding uRPF? I believe that since it is already part of the linux kernel and that it is regarded as standard for adavnced routers, it should be enabled in RourOS as well

Guys, could you please post speed test for SMB/CIFS transfers over Gigabit? Thanks so much

Theres something terribly wrong with your setup, this board has quite powerfull CPU which is able to bridge at least 600MBps without conntrack or QoS using big packets, no way its only 1.5MBps...

Well, that cavium OCTEON II sounds great, question is price, it looks expensive. Tell us more Normis! pleease

"I find it to be a HUGE oversight on the part of MikroTik/RouterOS that when I enabled switching only (no bridge) I lose visibility of graphing throughput on each port" Ofcourse, its because the switch is HW switch so once you enable it, it doesnt go through the CPU and doesnt slow it down...

we won't support ARM, but we have better plans Dont get me wrong, but unless you plan to use that 16-core XEON you were talking about in RB1100 thread, what better low-power CPU than ARM are you going to use in future RBs? Some new PowerPC, like e600? Atom? Atheros AR934x or some new MIPS? Either w...

Hello, I just finished reading very long thread about slow CPU in RB1100 on Czech ispforum.cz and then spent about 4 hours reading about ARM CPUs. The result is this: ARM is probably the only future low-power hi-performance CPU architecture. Right now there is Cortex-A9 dual-core CPU running on 2GHz...

According to this page: http://wiki.mikrotik.com/wiki/Manual:Sw ... p_Features , it appears that RB450G has ether1 LAN port independent on the switch chip, which not the case for RB750G. The advantage is higher troughtput from switch (ether2-5) to ether1 port on RB450G in routing or bridging mode.

Why dont you start using solid state capacitors? Are they that much more expensive? I guess that for router HW, which can be easily in operation for more than 10 years customers would wish to see capacitors that will last that long.

thnx for reply, I just learn by experience that I really need some default GW, but even with it, I still cannot force any local-originated to go through some other route than is the default one :( I tried output rule in mangle, with and with out local host address 127.0.0.1, even with some concrete ...

The question shrinked to this: if I am using only policy rounting with connection marking and routes only with routing mark, i.e. no normal default route (all 0/0 routes has some routing mark set), how do I match and mark connections from localhost to internet like ping or VPN? Output in mangle does...

Hello guys, I have a problem with policy rounting and PCC matcher. I have very nice setup with two routers in HA VRRP cluster and PCC over 4 different DSLs (2 in each router), everythings working nicely, except I want to use some VPNs iniciated from one of the router and I want either to use PCC to ...

I have never tried dial nstreme, but I use 10 ptp lines with normaln nstreme and turbo to get 60-70Mbps.

2 interpoint: and what happens when your RB600 dies? Try VRRP with two boxes, it is really great!

Hello, I have configured two RB450G (3.28) as VRRP HA cluster for LAN side. Each has 2 DSL lines using PPPoE and routers are connected to each other by dedicated cross ethernet line. It works very good, I only have to take care about outgoing traffic, mikrotik take care of incomming (related, establ...

Hello, one question: what is the more compatible match setting, both addresses with or without ports? I want to loadballance lots of windows desktops and I dont want to cause any problems as somebody have here with youtube etc. I guess that both addresses without ports should work good, only in case...

I think that the cheap and good way how to slove this is to buy come offline UPS and connect RB directly to the battery. UPS will make sure the battery is still charged. Or you can buy some big 12V battery (car starter battery) and some good battery charger with storage charge function and you have ...

If you need really fast PtP link, plug 4 atheros-based wifi adaptors (CM9 or R52) to some fast machine (> 1.5GHz CPU, not via chipset) on both sides and configure bonding of two nstreme dual links :) if you even use turbo, you get something like 160Mb Full Duplex link :) Use of gigabit NIC is sugges...

Please trust me (and not only me) that microwave energy cannot last reflecting again and again for more than a few miroseconds in some real situation in a house. Realize that majority of common materials absobs microwave energy, so even if you would have perfecty reflecting walls, it is still not en...

Try to learn something about physics, it is total nonsense. I study math and physics on university so I have some knowledge about this. 2. Good speed, good signal, but antenna is getting reflections off of other objects - A good example of this was a problem I was having with wireless inside a custo...

A recomend using normal PC instead of RB. My two PCs (K3-500 and celeron 600) can do about 6-7MByte per second on 1.5km line with signal -55dB on CM9 in turbo and nstreme. 6Mb is only with several connections (downloads from linux samba server), one connection can make only about 4MBps. When you hav...