MikroTik

samsung172

do a netinstall.

samsung172

you run confederation, and use whatever as you want as ibgp.

samsung172

I use the loopback ip:site id (same as ibgp as number) and if a router have more than one tunell, just take the next number (last octet) to next tunnel. eg my router at site 14 will be: loopback : 172.31.0.14 bgp as nr: 14 vpls id 172.31.0.14:14 router at site 175: loopback: 172.31.0.175 bgp as nr: ...

samsung172

wimax is an old way to do thing. Now days LTE is the way to go. wimax freq is not commonly available at open band. Hardware equipment and freq to use is limited, and there should not be a big market for devices using wimax. If you are able to use "out of band" 2,4 ghz, there are still the ...

samsung172

Hello guys! I just wonder if it's possible to run 2xBGP Full View with 100 Mbit each on RB1100AHx2? I have routing and NAT. For current 100M load cpu utilization is about 30%. Does full view increase CPU utilization and make impact for latency? I need time until CCR became suitable for BGP producti...

samsung172

add the server name and ip in

ros code

/ip dns static

samsung172

If there is misc client connecting to your AP (hotspot) and you have no control at client(s). Don't use encryption. it will not function 100% in mikroitik network.

So many clients does not have 100% compatibility to a wpa(2) etc encryption.

samsung172

Why don't you want to activate another pppoe profile?

samsung172

dual chain at AP, single chain at client(s) no problem at all.

samsung172

but your wlan and Ethernet to a bridge.

samsung172

EOIP has been unstable since it was released.

samsung172

Make a tab in right corner, make it possible to scroll in winbox. The change of one line per freq in scan list, make this function so much needed. From earlier, it was an issue to, but in so small grade. Now its an really big issue. I have this scan list: 5390,5410,5430,5450,5470,5490,5510,5530,5550...

samsung172

6.0 on CCR and X86 (only one tested) still have the vrf issue. ITs 100% CPU, and not even possible to do a /export or supout from the boxes. Is there any solution to the vrf issue, that have been in almost all 6.x versions. ITs impossible to use vrf on CCR, and that is a REALLY bad thing.

samsung172

try to enable/disable the /ip firewall service settings.

Some sip apps need it set, and some don't. Also change the udp timeout to a biger value. maybe 00:00:30...

samsung172

we make 433 with this setup, but using sr5 not xr. Its possible to do. and you don't need anything to power.We make io cards to this, make it possible to power even another unit of 433 and 3 SR. no problem with a standard power. We made an io card to old 532's to get power enough to the mini pci exp...

samsung172

If you don't set ip from the vlan's to the router, it would not route. Im sure you don't need em (if you aren't going to route.)

samsung172

check your l2mtu

samsung172

try to align your link

samsung172

put your l2tp interface in your bridge. Use the ppp profile bridge parameter.

samsung172

I don't know about a fib problem in 6.13, but it might be the problem in 6.14. I don't know what is the problem here. in pre 6.13 there was no way to make vfr working well. I have a ccr36 having a full internet bgp, and a lot of 1100's and some 1200 with ibgp (confederation) and ospf. I don't have a...

samsung172

just to say. I have had the following verions stable:

2.9.42, 2.9.50(51), 3.20, 3.30, 4.17 , 5.20 , 5.24 and or 6.13. I newer use any other ros than this.

samsung172

I have no idea about the lite (I don't think our supplier even would bring it to market), but in my opinion, 5.x and 6.x have really wired issues from versions to versions. It was an issue earlier to, but not in the same way like now. If there are 400 lite boxes with no problem, at same firmware and...

samsung172

try 6.13. something is buggy again in 6.14.

samsung172

Like always on issues like this.. change ros version.

samsung172

This is possible, and a nice feature. a 60Mhz channel at nv2, give me 80mb/s TCP instead of about 25mb/s on a 20 km link. (180 mb/s at udp)

samsung172

to se available variables you have set, and that are usable, do a

ros code

:environment print

samsung172

if pope is success, and you got an ip and a gateway (+ dns etc) you should be able to open what you want. included port 80, standard web

samsung172

Do it simple. Make a bridge. If MTU is big enough. its like. whats goes in, goes out.

samsung172

check cable, poe and... that you have power enough trough poe.

samsung172

Scan for wireless. connect, and add the correct security profile.

Then make your router a station. Have a dhcp client at wireless interface, and make a subnet to lan and a dhcp server.

Make a firewall src nat, masquerade rule.

samsung172

then make your firewall rule. block all but the port you want.

make a nat rule. before the "block" rule.

samsung172

just do it simple. add your l2tp interface to a bridge. Use l2mtu of 1280. Will always work, and no trobble with mtu. PS, use the ""hack"" /ip firewall mangle add action=change-mss chain=forward disabled=no new-mss=1280 passthrough=yes \ protocol=tcp tcp-flags=syn tcp-mss=1281-65...

samsung172

I recommend using a setup to separate interfaces, make yo able to prioritize over your bakup links. an easy setup would be default. but have a 100 prio to the backup p2p ospf connection.

samsung172

try to change your frequency. also check that in mimo. have all chains enabled. If all is ok. align align align and one more time. align.

This may be some error at hardware to.

samsung172

to do this hack use: /ip firewall mangle add action=change-mss chain=forward disabled=no new-mss=1400 passthrough=yes \ protocol=tcp tcp-flags=syn tcp-mss=1201-1546 To have this correct setup, use this: /ip firewall mangle add action=change-mss chain=forward disabled=no new-mss=1400 passthrough=yes ...

samsung172

do you control all sites between your l2tp tunnels= and know about the setup? Why have eoip over l2tp.? Use l2tp as a layer 2 protocol. much more stable.

samsung172

script to do what? It hink you mean setup. or config. Try to do a search in here. It's like 30% of all answer here. is about more than one wan connections. And how to setup. depends on your connections. and setup, plan and goal.

samsung172

its possible to run a script. say every 30 sec. to check if there is new connections. and if there is... run some kind of script.

samsung172

here you have to tell some more about what is your problem. what is your goal. and what is your setup.

samsung172

or just webfig.

samsung172

align, change settings and have good signal. Actually, the question have a tons of answers. but what would make your link better, is hard to tell. One thing a lot of ppl don't think about is fresnell sone, and that free lign of sigth, is not the same as free fresnell sone. eg, 1 meter abowe a roof, ...

samsung172

you have to use 5.x or 6.x on a 1100.

I did not think your problem is related to 5.x or 6.x.

samsung172

Try to use l2tp. Should be ok with mtu of 1280.

samsung172

Try to have your time and clock set. Use ntp.

samsung172

use some kind of viritualisation software to run windows "apps"

samsung172

I did not say. I had to downgrade to rc13 and all was ok. Seems like some of the problems around vrf are partly introduced in rc14. I cannot use it due to unstable router (hanging, not showing anny error in log etc. It also had a strange, not possible to start terminal from winbox. (wrong user passw...

samsung172

Seems like some of the problems around vrf are partly introduced in rc14. I cannot use it due to unstable router (hanging, not showing anny error in log etc. It also had a strange, not possible to start terminal from winbox. (wrong user password) teleneted from the link in, and it was ok. Something ...

samsung172

You can get calculation for windload. This depends on your mast etc, and have to be calculated from site, tower , equipment and a calculated wstimated wind on the site.

samsung172

you have to use some setup to "give" your clients a ipv6 address. my setup at home: /ipv6 dhcp-server add address-pool="ipv6 pool" disabled=no interface=bridge1 name=server1 /ipv6 pool add name="ipv6 pool" prefix=2001:470:d13a::/48 prefix-length=48 /ipv6 address add add...

samsung172

Your router will route between the vlans (subnets) if the router is the the gateway for the subnets.

samsung172

try using l2tp

samsung172

set your wireless interface as a station and connect to coorect SSID.

Put a dhcp client at your wlan interface.

Make some subnet at your Ethernet, and put a dhcp servet to it.

Make a nat roule in your firewall.

samsung172

do you have a vdsl modem? OR are you using the mikrotik unit into your phone line? This will not work, you need and vdsl interface, and as far as I know. Mikrotik does not support this.

samsung172

no. package and routeros is the same. eg, you need the pakage made for your routeros version (OS). Routerboard firmware is something else than the OS. try / routerboard print or upgrade. Its possible ( but not recommended) to run old firmware and new routeros (unless on some old bards, that need the...

samsung172

turn off logging to flash, and bad blocks are gone. This was really a problem earlier, in boards using CF cards. If you logged to CF, it would not last more than less than a year.

samsung172

Its possible to flip polarisation , even have "1/4" polarisation (X). To have good latency, I would use nstreme. To have high speed, use nv2. I don't know about your place, but I can get fiber at 1$ per 3 meter. I can hire splicing unit for one day, at 150$. If you have 100% free line of s...

samsung172

what are security settings? Try to use security - none

samsung172

The most stable boards I have, is old 532.

I have newer had troble with age, on boards from 133 and up. really old old old boards with pcmia slots, the old "home computer casing with wlan cards etc" is gone some years ago.

Capitor is a problem on some board.

samsung172

Consider the fresnell sone in a underground setup (link don't use free line of sight, but goes up and down) Its possible to use regular mirrors in corners. - Ore you need power to equipment. And, indeed, if you have a power cable. Why don't also have a fiber going with the powercable? NV2 and TDMA i...

samsung172

I Don't se this anymore. I have changed from NBMA to ptp, and it solved the issue.

samsung172

I think you have to post some more info about your setup. Im not sure, but do you have 2 routers to internet? Yo want one radius server (for hotspot?) and use same user/pass at both sites? Then I would use on box to "terminate" all and be a gateway to internet. Have site 1 and site 2 route...

samsung172

Put in wds mode, and "what goes in goes out".

samsung172

You cant just convert. You have to do a reinstall and have a new key. You might get this for 1/2 prize if you ask mikrotik support for a replacement key.

samsung172

I have no clue at all about that "omt", but why cant you use this box, and connect Ethernet to your mikrotik device.

samsung172

if free line of sight, and you don't need more than 20Mb/s - a Omnitik would do just fine. If you want more speed, some sector, and some more wlan cards and routers. I use a lot of ubnt 90 degree sector, and 411AH as AP, and r52hn connected to antenna. This will give something like 50Mb/s to 5 km. I...

samsung172

how is your config. Router-Stuff-Cpe ?

samsung172

you cant bridge. Somehow your net need to have a gatway, to route between. The easiest is nat.

just ass a src-nat action masquerade. out interface to your internett connection. and it should be ok.

samsung172

then its just to setup a external web cache. Or. plugin a usb disk to your mikrotik.

samsung172

use the dude

samsung172

actualy, this should work with one "small" mt box. But I would use 4, to be sure.

Its many configurations that is possible.

samsung172

check your log.

samsung172

how about disable hotspot, and see if the client reach net? IT seems like you have an hotspot error.

samsung172

make mangle and route rules.

samsung172

give the VPN client a IP in your internal network. Otherwise you need to give your clients a route.

samsung172

you could route. or nat. or make a tunnel to the old net. You just have to figure out. What is my current setup. What is my goal, and what opportunities does I have to reach my goal. In 90% of the cases, its more than one solution.

samsung172

there is no good answer to this. To make a AP to hotspot users, in a 100m circle, need some other hardware, than 2 km trough a big forest. and speed, to CPE 8km away, need something else. A good solution is some sectors at the AP - 5ghz, combined with some 2,4ghz stuff. so its possible to give net t...

samsung172

Update your routeros.

Still exsist, change Ethernet cable.

samsung172

go to Ethernet, and choose poe off.

btw, update to latest routeros, and do a upgrade of poe firmware (/system routerboard poe settings)

samsung172

You don't have a kernel installed. It tries your nand, and could not find your kernel. then it tries bootp, and still don't find.

Try to do a netinstall.

samsung172

connect the client as station wds, and the AP ad AP and dynamic wds enabled. Also have the default bridge-bridge option, and yor AP should work like a big switch.

samsung172

Use the Ethernet to your mikrotik device. Problem solved.

btw, have you asked your ISP to provede info about a connector in your site? Why should they not provide you that info?

samsung172

depends on your setup. A clean hotspot directly to a Ethernet should not. If you use vpls/mpls, eoip, vpn etc etc to get the cpe to the hotspot, its possible.

samsung172

its possible to try with upnp. I don't know if it will work for you. but if you are going to manualy setup dst nat, you need to know the internal ip. Like I say. its POSSIBLE to do this by a script, but its a hassle. I don't know of anny 15$ nat box's that is capable of automaticly update nat rules ...

samsung172

Why not use metarouter, and give him full access, to just the vlan10 stuff.

samsung172

Its like YES to all. But I would assume a VPLS to each router from a concentrator etc, and have the VPLS into a bridge interface. (maybe with horizon) Its quite simple. make a loopback, and have a loopback ip. Have a link net to next router, and put the interfaces to this l2 net. Also enable MPLS to...

samsung172

connect and try to ping and have the do not fragmet bit set.

Try to have a mangle rule to change mss (a hack).

ros code

/ip firewall mangle add action=change-mss chain=forward disabled=no new-mss=1200 passthrough=yes protocol=tcp tcp-flags=syn tcp-mss=1201-65535

samsung172

why not just give the client a IP address that does not change. Its possible to do with script, and pick ip from mac address, but why make so much mess?

samsung172

You have no info about your gateway. That is needed to have this to work. to have 0.x client to connect to 2.1/24 the 0.x need to know that 0.29 is gateway for 2.1/24. Also you need some default gateway. I assume this is 0.1? Its also possible to do a nat. (Src-nat - action masquerade out interface ...

samsung172

You need to provide some more info about your net. l2? l3? (routed or not) etc. One way is to have the AP in wds mode - Dynamic and have default bridge bridge. Also add your Ethernet to that bridge. Then put your SXT's at station bridge, and put the link interface to bridge together with the Etherne...

samsung172

Is your connection tracking enabled? In case, try to switch off

samsung172

If you se, its not changing the packet size (counting 0). There have to be something else.

samsung172

Try to force 1G at both ends

samsung172

You have to know what module is used in the other end.

samsung172

Or just put a bunch of devices to do roaming.

samsung172

Routeros + metarouter for additional app.

Try some other contry code.

samsung172

seems like client ask to reconnect. Try to post the client log.

samsung172

try first - securityprofile = none (add a profile, with no parameters, just name=none) and see if this helps.

samsung172

think... interfaces.. what interface. physical or viritual is connected to what? and what do I want to recive. eg. I have ether1 connected to the switch give the dhcp ip.. ok.. then ether1 needs to be the dhcp client interface. If the ether1 is connected to a bridge, ok.. then the bridge is the inte...

samsung172

Nice uptime (you should se mine at the last 532 I was upgrading. over 700 days)

Still, upgrade is more important than uptime.

samsung172

/ip firewall would be the trick. you could make a bounch of rules, based on a marking of something. lets say port 22, or just have one rule, directly to port 22. (or something else)

samsung172

Use routeros

samsung172

Yes, you can use vlan on a switch group

samsung172

I don't 100% understand, but if cisco is chaping to 50 MB/s, this could be the issue. Cisco is known to have really limitations and troubling shaping features.

samsung172

this you can make in php.. Do you mean user can tell" hey" I forgot my password. I want it as an sms? This should be done in your php website. (Hotspot???)) If your goal is to have an sms, automaticly, if radius detect wrong password, you have to use some kind of trigger, that say "he...

samsung172

Then You need to try another netinstall/software version.

samsung172

then bridge your wan and lan. set IP from provider to bridge. Its possible to have a local IP to the bridge, and have a dhcp server here to provide to more units. But, I don't know how this will impact your isp. Its better to use 2 port for "lan". 1 port for dhcp clients and one port for s...

samsung172

hope you mean fetch.

please provide som more info about the script. maybe the source=? what do the script do, and what is your goal ?

samsung172

well. filter only match the mac address of bridge interface. try to set admin mac, static, and do the filtering. I use to set the mac static to whatever present, but change first 2 variables to 66. eg 00:42:c2::xx will be 66:42:c2::xx

samsung172

use queues to set bandwith. it don't matter. what the interface is.

samsung172

I don't know why. but have a script. setting the global a couple of times during each day.

(PS. global's are gone if router is rebooted)

samsung172

Its possible.

I think what you want is a bridge with 2 gateway IP.

A dhcp server at the interface (bridge) and the possibility to set permanent ip to some devices.

Its possible to do with vlan, but why stuggle with vlan's?

And... routeros. is capable of almost whatever you want.

samsung172

do a netinstall.

samsung172

actually what you describe, is to connect a 100/10 connection without poe to mikrotik. this will make a port/interface active. as loopback, it would just connect to itself. You can use this port, to a lot of stuff. Loopback interface, internal, is one thing, but loopback in Ethernet is also possible...

samsung172

why don't you make this your own? its possible, by using a board with 2 minipci and have some N-plug or rp-sma connector from each cards to antennas.

Btw, do you get better performance, by doning nstreme dual instead of N and nv2? (in dual chain)

samsung172

use check gateway arp to make this work. in nat, don't use out interface.

samsung172

what is the kernel panic message?

samsung172

MLPPP is really an underestimated feature, generally spoken. if anyone make a MLPPP implementation, capable of bundling different connection speeds, and to multiple servers at once, it could be one of the most valued redundancy and bundling protocol/feature ever made.

samsung172

use bridge filter

samsung172

China.

I use http://www.gigacom.no/who import from china. IT's cheep and quite good.

samsung172

seems like you have a net that is replying like that. How about your wireless links? Are they stable,up and ok?

samsung172

What kind of crash in VRF? Is it reported to support? At all system/boards I have tried with 6.rcXX, the enabling of MPLS-BGP is ok, but at once as a VRF is created, the system stop responding to commands. Its not even possible to do a supout.rif file. http://forum.mikrotik.com/viewtopic.php?f=19&a...

samsung172

Guys, thanks for the input. ^_^ We are just looking at 50Mbps estimated bandwidth. Samsung172, may I know the bandwidth of your tested 20km SXT-G links? And, others who have tested SEXTANTG 20KM point-to-point, please share some inputs, including the bandwidth that you get. Thanks a lot About 50Mb/...

samsung172

make this in perl or something like that. remove all unwanted stuff, and put the desided IP to addreslist PS, have you tried CYRUM with bgp? It have bogons table, and could drop route to internet bogons. Its seems like you just want the RIPE AS's and routes. There is more in the world. ARIN etc. Rip...

samsung172

also check :

http://forum.mikrotik.com/viewtopic.php?f=1&t=70318

samsung172

Put the ip to the bounding interface, and put it in bridge. Then the router should respond.

If you use a routed setup. put the IP to a loopback interface (bridge) with an /32 netmask.

samsung172

what happening in this setup if you add a routing filter, telling to drop all routes to other bgp? Is the problem still exsisting if the BGP connect? And if this work no issue just by a BGP connection. Try to loosen up the filter, and receive the routing table from the other side. Don't send your. W...

samsung172

is this wireless setup? If so, it could seems like you have some issue to a link. The link drop, but the pppoe session is still up, don't time out (at server). When client after a dropout (in moust cases unastable wlan) it will try to reconnect. The pppoe server then say. hey. I have a connection al...

samsung172

Its like the rest of life. To get you have to give.

. If a person never give, he will never get.

samsung172

try to delete all your files folder in X:\Users\username\AppData\Roaming\Mikrotik\Winbox

samsung172

this is a common thing. that have been way back to 2.9.23 ore something like that. At once as you put an wlan interface to bridge, there is a bit random, if its possible to do a mac telnet directly from registration table, or if you have to go to ip-neighbor and take it from there. (even if mac is t...

samsung172

Hello,

in fact i didn't found a solution to that problem. So i decided to do something uncommon i downgraded to 5.24 and
now it works like expected. So there is a problem in 6.0rcX with bridges and ipv6.

Cheers

meno

Tike to much other feature. don't use the 6.x in production

samsung172

Well. today. only answer is, run 820.11 to use VAP, and don't use the nice feature from NV2. The VAP feature, is really a wanted feature of nv2. In many setup, the use of vlan, and same ssid, is not an option. This is really a BIG HUG discussion thing. The choice for us today, is to run same SSID at...

samsung172

Well. if you did exactly as in the manual. you need to provide some more info and config of your setup.
And, update to lastest 6.x

samsung172

but.. yes... 20km. you should be able (if not to much noice) to get the same speed as your Ethernet port.

I have some 20km SXT-G links. Running like a charm (and 3db weaker antenna, and no high power)

samsung172

I don't really understand you, but if you have the control of routing in both side. a dynamic protocol would be preferred. If you don't have control of the routing, eg, connection to your ISP (without Global routing), the check gatway arp, is nice. (to pic the second if first is down)

samsung172

Hi Mat, thanks for sharing! Your BGP Sessions are up with Fulltables? I plan to use Mikrotik in my Edge with 3x Uplinks, but i miss 10 GbE Support over SFP+. Hi raz I'm running one full table, one part table and one table from the local IX (~50k). The downstream router gets the "mix" of a...

samsung172

Has anyone tried v6? Those routing crashes should be fixed.

Not possible. due to the crash in vrf.

samsung172

I have 4 CCR 6RC11 the core VRF with no problems. What you guys been experiencing problems? At all system/boards I have tried with 6.rcXX, the enabling of MPLS-BGP is ok, but at once as a VRF is created, the system stop responding to commands. Its not even possible to do a supout.rif file. http://f...

samsung172

still the vrf issue. so its not possible for me to start full test.

I have a global ebgp routing table, and one internal ibgp and see no problem to that.

samsung172

you use a failover based on netwatch. Why not base it on routes. Make all devices knoe about all the other, and put weight to routes. Use ospf, bgp or something to make it dynamic, and its should be redundant by it self. Without a netwatch etc.

samsung172

try to connect to another Ethernet than ether1 and use winbox to find it at mac-level.

samsung172

well. this indicate some error at transport from pppoe clinent to server.

I monitor my CPE's, by polling how many pppoe login/logout they have in 1week/ 3 days/ 1day/

samsung172

!

If this could compare to meru controller, we have a new world in outdoor wifi hotspots. No config, just plugin a device, and it is working.

samsung172

ntp client should be a part of the combinded package.

However, I think there may be a bug in 5.x (new) that for some resion remove packages. I have seen this at sextants.

samsung172

how about upgrading/downgrading ros?

samsung172

but. this depends on what kind of traffic you are going to shape, and how the CPE is connecting. You have to tell some more about your setup, and goals.

samsung172

same as eth1?

samsung172

do youhave the unit in the ip neighboor list. Try to mac-telnet from there, not wireless registration table.

samsung172

as far as I know. no support for ac (yet)

samsung172

And some more "spamming" to the post ( Im missing a lot of old config stuff): /log print 01:00:09 system,info verified routeros-mipsbe-5.23.npk 01:00:10 system,warning ghost file /root/prism.hex 01:00:10 system,warning ghost file /old/wireless/update 01:00:10 system,warning ghost file /hom...

samsung172

You have to tell some more about your setup. Hotspot? pppoe? dhcp? how do the customer connect? what happen after the box they connecto to. It seems like you like to give them a new gateway? (trough new isp) is it static route? or dynamic?)

samsung172

how about your RSTP?, is it blocking?

samsung172

The easiest way - Reset config and remove default.

then make a bridge, and put your desired interface to the bridge.

samsung172

How about dynamic routing?

samsung172

For some reason. I don't know. it did not installed the wireless package. (+ a lot of other) (was fully operating in 5.22)

Downgrade to 5.23, and it all came back. (I keep it there. don't upgrade to 5.24, and try to install just wireless package).

samsung172

Today I upgraded my net to 5.24. All went ok, except a SEXTANT that "missed" its wlan interface. # DEVICE VENDOR NAME IRQ 0 00:00.0 Atheros Communications Inc. AR5008 Wireless Network Adapter (rev: 1) 2 [admin@xxxxxx] /system resource pci> /interface wireless print Flags: X - disabled, R -...

samsung172

I have tested about 100 SXT's in cold Norwegian winters, and quite rainy climate, about 1,5 years, and I have still not any SXT that have broke in field.

samsung172

Its possible. How many depends of the load and space you are going to put to each metarouter.

samsung172

Setup a router nr 3. cheep. Add l2tp server at this. Then make l2tp tunnels from your 2 boxes, and access trough the IP at the VPN interface.

samsung172

I have seen link net, and devices in linknet between 2 routers, dropping in ospf, IF! using ptmp mode instead of ptp. EG: R1-Wlan1-Wlan2-R2 R1(ospf)-resolve(x.x.x.1/29), Wlan1 (pure bridge, x.x.x.2/29)-don't resolve, Wlan2 (bridge, and x.x.x.3) - don't resolve, and R2(osfp), again resolving (x.x.x.4...

samsung172

Well, consider to encrypt, loose SOME performance, and have the funny ppl out of your net.

I use static - aes-ccm, and I cant say that performance is affected. In 2003, maybe. in 2013, with new hardware etc - NO.
and to isolate l2 in mikrotik, fulfil your net with horizon at bridge interfaces.

samsung172

All of the above. RT1 to cisco switch to Canopy AP --/to/-- Canopy AP to RT2. I was wondering the same. I thought I understood MTU to be an issue with OSPF. Check 2 things. Enebale bigger mtu at the 2 interface connecting together, and try to ping with lager packets. (and set do not fragmet option)...

samsung172

I don't think so. (but, im not THAT into it. Maybe possible using VMware, and usb disk as storage, but to me, to much hassle) But you can buy a 100$ computer, and a 3 terra disk, and install ros to it. Then use the disk as web proxy. If you want some more "flexi" stuff, have a raid setup. ...

samsung172

buy a cheep PC and use as web proxy.

samsung172

dude, SNMP or something like that.

http://en.wikipedia.org/wiki/Comparison ... ng_systems

samsung172

connect using a serial cable, and check log, CPU usage etc if happening agane

Sounds like some kind of loop

samsung172

But, is it R1 that is neighbor of r2?

edit : And what is between the 2 routers? wireless? Ethernet? switch? etc. MTU could be an issue here.

samsung172

should be possible using :foreach :toarray and :pick stuff.

samsung172

Still waiting for the vrf fix so its possible to implement v6x to core routers.

samsung172

I have not tried static routes. I have 100% ospf routing in backbone/management and bgp to internet vrf. still, the second router, in same l2 net, would respond to a ping (in same broadcast domain). I have just problem with the establishment of the ospf. Some traffic is sendt between routers, but wi...

samsung172

Try to use another ROS than an old 6x beta.

samsung172

do you have control/acces of the hotspot router? Or are you an end user?

samsung172

Its possible to trim it more, and use 1480 etc. Then it would be less impact to performance.

PS, don't use it to smaller than 1280, then ipv6 will stop working.

samsung172

Use NBMA or better pt(m)p mode. Use of ospf broadcast can be quit painful. Do the following to have a clean setup: R1: add the /30 (I use /29, just to be sure) to the interface pointing to R2 (or more, if bridged with more routers) R2. Add the next ip, in the same subnet as R1 pointing towards R1 Ad...

samsung172

if MT ake a psu nr2 option, and provide a hotswat option to this, the CCR would (after software upgrade that is consider as stable) be the best broadband router at marked today ( at a price the 90% smallest company could afford)

samsung172

use ststion bridge and bridge. remember to have a l2 mtu big enoug to pass troug vlan (1504) ((1518 in qinq (((valn over vlan))))). always do a bridge between ethernet and wlan interface

samsung172

pptp dont give you a l2 net. to see all computers connecting to the same net. try using l2tp instead

samsung172

bridge mode would be the same. as long as yor l2mtu is enoug tho pass trough a vlan (1504 as standard) it will work.

samsung172

This tell to less to conclude annything other than mikrotik is working to get a 100% systeem running. its still to be consider as a beta test system.

samsung172

+1 , but all this is possible to do in a website. to do the winbox stuff: (install java) [HKEY_CLASSES_ROOT\winbox] @="URL:winbox Protocol" "URL Protocol"="" [HKEY_CLASSES_ROOT\winbox\shell] [HKEY_CLASSES_ROOT\winbox\shell\open] [HKEY_CLASSES_ROOT\winbox\shell\open\comm...

samsung172

check your security profile.

samsung172

I understand. and I know. I have implemented this my self. Still, the NAS will know the subnet given to the customer, and will know the "route" by the interface (pppoe) used to give out the net. The cpe you give one ip. (Not the whole subnet in first place), at pppoe interface. You put the...

samsung172

I will test that it is working. :D No, but seriously, I have had some trouble using the vrf part of 6.x ros, and im not quite sure if the routing is good enough to be used in production yet. I will try to stress test, (maybe to my j6350 and/or my zte zxr10 8902) for eBGP and to my 1100AH2X for iBGP,...

samsung172

Im canging a juniper j6350 to a ccr on Monday (if I recive it).
I will have a global bgp routing table to it and we'll se then.

samsung172

You actually don't have a route at your router. Just your subnets.
(or is the 6.x config fooling me? It don't give the 0.0.0.0/0)

samsung172

then you need bridge - wds. ( or eoipe etc). The point is to get a l2 connection between 2 devices. Its not possible to do mac telnet after a gateway (then you must use eoip-vpls-l2tp or something like that)

samsung172

But what route do you actually need if you setup BGP between nas'es, and give out from one big pool to the clients? then the pppoe, who become the clients default gateway, will fix all the routing (if you see the nas'es as backbone with bgp)

samsung172

Try to use some of the convert stuff here:

http://wiki.mikrotik.com/wiki/Use_Funct ... CMD_Script

samsung172

Try to do a bgp to route subnets to the pppoe terminators. Then it don't matter, what IP is to where. its routed dynamic. all pppoe terminators could have the same big subnet.

samsung172

mac telenet.

have the wirless in wds mode, to go stight trough with winbox (or mac telenet).

Or you can first mac telenet to firstdevice. then to second.

Its also possible to do eoip, l2tp, mpls/vpls etc.

Also remember to mac telenet to correct mac address. Try the one provided in neighbors

samsung172

inbound?

samsung172

root path cost.

samsung172

There is 2 thing to do here. algin algin and more algine at antenna. Also nv2 or nstreme/802.11 is a bit of what you want. low latency or high speed. second to do here, is to use some freq that have the less amount of noice, AND! is compatible to antenna. (im not sure of the stationbox, but MT SXT i...

samsung172

MT use MPLS and VPLS (EoMPLS)

samsung172

put the sxt's in WDS link (ap With wds mode, and station-wds ), and there should be no more config other than tag (and or untag) the vlans at Devices poninting to your net. Edit : Need l4 sxt. If not l4, use bridge mode at AP and station bridge at station A bridge between wds Interface at AP and Eth...

samsung172

At least you need som config to the Interface pointing to mikrotik. how about Security? if you drop the Complete config, its more easy to say. as a start, you need Your "link net" between the two routers, and the loopback configured in Networks. also you need to setup the Interface Connect...

samsung172

you will need, ppp profile. ppp user and a network (IP's) to Connect to both sides.

If you want to use the l2tp as a bridge, have the defualt bridge option in ppp profiles.

when all is up, you can have a l2 net over this, but also, possible to Connect the eoip, to the address of the l2tp tunnel.

samsung172

tomaskir , samsung172 thanx alote my goal is > user connect at broadband connection his user name and password are athunticate in pppoe server number1 if not he connect to another server or any way other can i get it ? You can script this at Client side. somthing like: Connect to pppoe server With ...

samsung172

should still be possible to change the port you are Connected into if using bridge.. You however need to have physical Access to the router.

samsung172

hi, similar problem, but infrequent issue on one wireless link, -55/-56 94/99 ccq ap/station bridge nv2 (omni/711) v.5.21 everywhere, ospf ptmp (for unicast), was stable, but recently has problem once a week to once a hour some observations: - on AP logs: state change Full to 2-Way followed differe...

Search found 1191 matches

ros code

ros code

ros code