MikroTik

If this is Intel 100HFA016LS or other similar Intel OmniPath - this card supports OmniPath only - no support for Ethernet at all. This card will not be supported in RouterOS.

Hello, fix hopefully will come with next beta release.

Next beta (after RC and stable) release, should address some of x3 issues as well. Hopefully mdmg-fix could be switched to off onward.

Fix should improve stability to 802.11ad line as well. Unfortunately we will not have it ready to next stable release cycle.

We have potential fix for PtMP issues. We are still testing, but it should be ready in next beta releases.

Thanks! Well, I hope that a new release is coming soon, at least as a beta!

Fix is included in upcoming beta

Thanks for report. This is known issue - automatically "servers" field is passed to container, but in case of DOH this field does not exist, for quick fix set/change DNS in container setup to Routers DNS IP address -
/container/set <your container> dns=192.168.88.1

NVME-tcp has nothing to do with physical NVME disks. Target can be USB drive, NVME drive, SATA drive or even part of RAM on the device. Same goes for iSCSI and all other mentioned protocols. ARM based RB1100Dx4 Dude edition supports 4 SATA drives, making it a good candidate for ROSE package testing ...

is it possible to get supout.rif files from this case? Please send it to support@mikrotik.com with reference to this thread.

ROSE-MANAGER still cannot mount iscsi devices from QNAP/Synology NAS to CHR: Thanks we will check this Can you please advice how to rename the disk? I habe usb1 or nvme1 and if I change the name, the error "can not change device type (6)" appears. thanks, this is Winbox bug, should work f...

thanks for reporting this, we will check how to fix this in upcoming versions

USB Gb ethernet adapter (Techole UH411) with Realtek RTL8153

This chipset was never fully supported. we will check if we can add it properly.

What is the reason for that slow transfer?

SFTP is slow single connection protocol, run multiple instances parallel to get faster results.
For rsync - please read rose manual page.

@rameex43
make raid1 with tcp-nvme drives

@Babujnik
Thanks we will try to fix this.

@sirbryan
Simple partitioning will be available in upcoming versions. We will check what we can do about LVM or ZFS.

@issme
RDMA is different beast, currently its not planned.

Feel free to suggest other protocols and features that should be supported.

The rose-storage module also has command additions in /file/sync.
However that is completely undocumented and not so easy to figure out...

this is rsync, i will add documentation tomorrow for this

please comment ROSE package in designated topic viewtopic.php?t=192888

Hello,

please fix this (SUP-104510) . Thank you

this issue is not related to new ROSE package. SMB in ROSE package currently will only support SMB2.1 SMB3.0, SMB3.1.1 dialects

macOS fix for SMB will be available in next release

simple "/" should work as path. Currently nfs/smb is applied to disk. If only exact folder is required on client side - use "slot/folder"
f.e. on linux initiator:
sudo mount -t nfs 10.155.166.7:/sata2/stuff /mnt/files

Windows users be aware that default built in NFS client does not support NFS v4 mode.
https://learn.microsoft.com/en-us/windo ... s-overview

maybe anyone more competent in windows systems may comment on this. Is there any good third party tools or workarounds?

What's new in 7.8beta2 (2023-Jan-20 12:27): !) storage - added new "rose-storage" package support for extended disk management and monitoring functionality (ARM, ARM64, Tile and x86) (CLI only) What's new in 7.8beta3 *) rose-storage - added support for GPT partitioning (CLI-only) *) rose-s...

mount -t nfs server:/path /mountpoint

nfs-share=...
documentation is still in progress

ROSE package includes different formatting tools, please check formatting with ROSE package enabled.

no, only power is connected to USB port for this model.

Free package, available for arm,arm64,Tile and x86

Several comments:

Thanks noted.

Nice changelog, I don't know how to find that "rose-storage" ..

documentation draft:
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

you need to install rose-storage package first

viewtopic.php?t=192810
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

So my point is if Mikrotik is going to be promoting container usage...they should try to make available on all platforms.

Please show us tools for building containers for those platforms and working example.

Thanks, this will be especially useful very soon

Edit:
https://help.mikrotik.com/docs/display/ROS/ROSE-storage

' WD Red SA500 M.2 ' will work, any SATA m.2 should work.

we have tested drives up to 1TB, but i don't see why larger drives would not work. From software side there is nothing that blocks larger drive use.

i have already answered this question previously.
viewtopic.php?p=953660#p953567

CCR2216-1G-12XS-2XQ supports only SATA drives in M.2 form factor slot. none of mentioned NVMe drives will work. You should look for M.2 2280 SATA III. SATA III drives support up to 6Gbps As it goes for throttling - this greatly depends on use case. For light Container use - this shouldn't be noticea...

we would need step by step how this can be repeated.
For me files always stay with correct uid,gid when upgrading from 7.6 to 7.7

@elico
looks much better, newer versions (7.8 brach) will allow to change .type permissions without extra steps.

@TheNetworkBerg
Thanks for your videos! I will try to repeat upgrade issue.

fix for .type will be available in next releases.

@elico .type file inside mounts is for RouterOS to mark folder contents as not to be listed inside RouterOS. Correct fix would be not changing permissions for this file from uptime-kuma side, or allowing permission change or change the way of listing/not listing folders from RouterOS side. Deleting ...

Thanks, i just tried, and yes, there is small bug that would not allow to start this unless you do few extra steps (fix will be available soon) Setup container setup as explained in our help page (add registry url, add installation medium, set tmpdir if not enough memory on main disk) setup mounts: ...

RouterOS is not based on systemd

So what exactly is broken? Use of the RAM disk for container storage?

In this case, cause is not related to tmpfs

Thanks, I managed to repeat this issue. This was broken somewhere from stable 7.6 to rc, release. You can use 7.6 for now, as bare Openwrt uses only 8.8MB on arm64 systems / # cat /etc/banner _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_...

You can use armvirt target -

docker import https://downloads.openwrt.org/snapshots/targets/armvirt/64/openwrt-armvirt-64-default-rootfs.tar.gz openwrt-arm64
docker save openwrt-arm64 > openwrt_arm64.tar

This issue brings in problem in starting containers. All I need are to re create and do some minor configurations Please elaborate. Name(slot) does not change on previously added/formatted disks. On newly done formats slot will assume new name based on physical slot. If name was "disk1", ...

Currently I have done the test on a hAP ac3 (arm) and the same thing happens, the global variables disappear from the environment after a few minutes of closing the winbox.

Thanks, we repeated the issue

What's new in 7.7rc1 (2022-Dec-08 16:38):

*) interface - show RTL8153 CDC Modem Device as ethernet;

I can't set or get the disk name on my hap ac3.

Disks now have slot, as their name. This will be included in Winbox in future releases.

/disk set 0 slot=...

*) disk - added support for manual RAM file system (TMPFS) creation (CLI only); Great news! But this means we will not see the default behavior to change on devices that did not use a RAM file system till now? So to have consistent behavior (and paths in scripts) on all devices I create a disk of t...

You need to add the variables for your container before you pull it down: /container/envs/add key=cap-add name=MYCONTAINER value=NET_ADMIN /container/envs/add key=device name=MYCONTAINER value=/dev/net/tun Where MYCONTAINER is the name of your container. /dev/net/tun access was added in 7.5beta4 an...

Maybe it could be combined with a new feature to have RAMdisk on ALL devices with sufficient RAM (not only those with insufficient flash) and a compatible
and predictable way to store persistent and nonpersistent files?

maybe in next release

Should I expect the file system on RouterOS to go from using "disk1" to "sata1-part1" as the "root" directory name? Disks will now carry names where they are physical connected - it will make finding physical disk much easier. After formatting, there will be no issues ...

nice job! Thanks for sharing!

/dev/stdout and /dev/stderr permissions are fixed in latest beta releases (starting from 7.7beta6)

mounting files instead of folders are not yet implemented.

there will be fix for similar issue in upcoming versions.

Fix for this will be available in next upcoming versions

Is this 32bit CPU?
x86 32bit only is not supported by RouterOS v7

openssh isn't installed in ubuntu containers by default. You can use shell to access your container -

/container/print
/container/shell 0

Thank you for reporting this, we found main cause for this issue, but it will take same time until fix will be available. Currently as workaround please mount /var/log as explained by previous posters.

The same way tun/tap access was enabled in containers under RouterOS maybe access to usb devices can be enabled too, with a proper feature request.

this is in our to do list.

PCIe AHCI or PCIe NVMe ?

PCIe NVMe !

1100AHx4 had SATA drives, CCR2116-12G-4S+ uses PCIe drives

Thanks for detailed reports, we will look into it.

I tried on a RB5009 and this zabbix/zabbix-proxy-sqlite3:alpine-6.0-latest tag has linux/arm64 in it: https://hub.docker.com/layers/zabbix-proxy-sqlite3/zabbix/zabbix-proxy-sqlite3/alpine-6.0-latest/images/sha256-44a5cdd64302b2a061415a3f31a31704b8aa4a15d2c31a0ae5084d20c0271a22?context=explore remot...

I see the mounts, but I want to write to them, which is not possible (permission error).

I can't reproduce this. Please write to support with exact steps how are you getting this error and reference to this forum thread.

stop/start newly created and started container and mounts should appear. We will fully fix this in next releases.

I'd like to see IPv6 support. thanks, noted. - The CT can't write to the mounted dirs - is that normal? Is there a way to write to them or to any place that's visible on the host? I need the container to write logs and status files. mount folders are not browsable from RouterOS, but you can access ...

i think i got where it goes wrong. As a workaround currently you can after adding container start it, stop it and start again. Mounts should appear. we will try to fix this in next releases

I'm running RouterOS 7.5beta4 on my hAP ac³ and: 1- mounts still doesn't work for me; 2- I noticed that a default route is not being added to my container, even though gateway is defined in interface/veth . 1. mounts needs to be removed and created again if upgraded from version with broken mounts....

Could you allow systemd to work inside container?

NO!

That sounds good! How will it be supported?

/dev/net/tun device now is available for container use

tun/tap support will be added in next release. Anything else to consider adding before stable release?

5GHz interface is designed as backup for 0.001% of time when main 60GHz interface is unavailable. it's not designed as Access point for other wireless clients or other uses.

Mount issues should be fixed in next release. Will it be possible to add capabilities to containers? For instance, cap NET_ADMIN is required to create/use TUN/TAP virtual network devices for various functions. OpenVPN or other VPN solutions, like OpenConnect requires this functionality. currently th...

Is it fair to assume that the MT containers do not support the equivalent of Docker bridge mode networking?

And if that is correct, is future support for bridged mode on the roadmap?

how is "bridge mode" any different from current implementation?

mount issues are still not fully fixed - but we are working on this issue.
is there any more functionality we should consider adding before container goes to stable release?

My laptop is old though, nothing recent about it.. Two mPCIe ports and two other ports that I'm not using (one is another mPCIe, do not remember the fourth's form factor right now).. MC7355 is from 2012.. It had a MC7455 but it died a few years ago, so I put the MC7355 back.. Yes, it is time to loo...

is this still repeatable in v7? if yes - please contact support with supout.rif file.
information here is not all correct. Modems should be supported on all systems equally.
X86 installation is still supported.

specifying directory will be possible in next release

have you added this mount entry to container as well?

/container set 0 mounts=config

Please use main container thread for questions regarding containers.
viewtopic.php?t=178342

for lazy Bobs, there is remote-dist to dockerhub, where you can be sure that what you see is what you get.

running sshd into container is bad practice from start and is not correct use of containers all-together.

it runs for a moment (<1s) and then stops. same with debian image. in my case disk1 is an 8gb usb2 flash drive freshly formatted in winbox as ext4, but same behavior if I try to it on the device's storage are you running any command inside container? If not this is how it should behave. try runnign...

why would anyone download image from unknown source when this can be done in few minutes locally and safely and to any supported architecture? make Docker file with contents - FROM ubuntu:latest RUN \ apt-get update && \ apt-get install --no-install-recommends --yes openssh-server &&...

currently you can follow instructions b and c. Next releases will make pull directory configurable.

We repeated

sudo: effective uid is not 0, is /usr/bin/sudo on a file system with the 'nosuid' option set or an NFS file system without root privileges?

issue and found the main cause. We will check what can be done.

probably not enough memory for downloading and extracting layers. Use pre-build or pre-fetched image instead. Variant B or C in docs

Looks like all permission issues are caused by accessing previously created containers, containers are and should be isolated from each other - if same files are required for multiple containers use mounts. Do not put mount src in root-dir either. root-dir should be on external memory for now.

sudo: effective uid is not 0, is /usr/bin/sudo on a file system with the 'nosuid' option set or an NFS file system without root privileges? Please check that the disk is mounted as disk1, also check if reformatting from RouterOS helps. I have similar setup, only difference my disk is formatted with...

@bma and others, regarding container - please use other threads to discuss container in detail

set environmental variables as per docs DNSMASQ_USER should be root

Two quick questions about containers:

1) are veth interfaces mandatory, or can host networking be used?
2) the docs state that ext4 is supported, is this new? Any plans to add ext4 support to Disks > Format Drive?

1) Yes
2) Disks are formatted from RouterOS as ext4 for a while now.

CCR2004-1G-2XS-PCIe is istalled in first PCIe3.0 slot?

If there is slight rattling - this does not affect functionality, devices will work fine.
If there is part loose inside shell - return it to RMA.
Shells are welded, they are not designed to be taken apart.

next v7 beta version will have potential fix for this issue. Do you know the cause of this behaviour? We have dozen of nray link in production since months/years and only this specific link has this trouble. We even replaced both nray and tried to swap a nray by a wap60. Knowing the cause would hel...

next v7 beta version will have potential fix for this issue.

that table explains 802.11ad standard available rates.
those devices does not support MCS 5 and 9 and other MCS's are disabled to improve stability.

@antonsb is there any planning for other OS/hypervisor support, e.g. VMware ESXi 7.x ?

we will look into it

@tensioncore @pe1chl
this card currently has drivers in Linux latest Linux kernels and BSD.

@ns88ns
no bifurcation required, Linux system will see 4 network devices

5GHz antenna holder allows some play on early models - this is fixed in later revisions.
Devices can't be opened without destroying outer case.

return container support

soon! just some minor things left.

Using two PCIe cards or USB based (LTE modems) are supported, but there are some limitations. To use two LTE modems - USB lines has to be switched by removing jumper near USB port. If two pcie (wireless) cards needs to be used - there are some limitations to bus speeds that may cause performance iss...

https://mikrotik.com/product/RB435G#fndtn-downloads
Under Downloads you will find dimensions pdf that will help you to design enclosure.

you are missing http-method

judging from signal strength - your alignment is way off.

This is due low gain antenna? WHich is the difference from LHG60?
nRay and LHG 60G is supposed to be capable same link lengths. Why to lower power limit for the nRay and not for LHG 60G? How that will play out?

This power limit is active when "region=eu" is used

sure, sorry i gave v7 compatible code v6 will look like this foreach i in=([/interface wireless scan wlan1 duration=5 as-value]) do={if (($i->"ssid")="Test_Network") do={:put $i}} so what does this do: /interface wireless scan wlan1 duration=5 as-value does scan for 5 seconds and...

yes, you can in multiple different ways: 1) if you can connect to network - you can check interface status (running or not) and based on that write a script 2) if you can't connect you can check log messages when interface tries to connect, but fails 3) You can run scan and check if ssid is present ...

Signal is representation of signal quality in percents. It depends on MCS used and crc error rate.

802.11ad works worse in cold weather not becouse it is freezing. Cold air becomes more dense and amount of oxigen per squere mitter increases.

This is True, but we had some software improvements regarding this as well:
6.49beta46:
*) w60g - improved stability in low temperature environments

Antonsb with the New regulations in the UK coming into force in November 30th, do you think Mikrotik will add a power control to turn down the output of the Nray to 40dBm to comply? https://www.ofcom.org.uk/__data/assets/pdf_file/0023/218129/2021-LE-exemption-statement-final.pdf Regards Paul we wil...

this will be available on new 802.11ay hardware.
Unfortunately this cannot be used reliably on our existing 802.11ad devices - that is why this frequency support is removed
Antonsb it works well.... what we are missing?

stability in raised ambient temperatures

this will be available on new 802.11ay hardware.
Unfortunately this cannot be used reliably on our existing 802.11ad devices - that is why this frequency support is removed

Next beta version will have possible fixes for some disconnection issues.

Yes, devices can be used in routing mode as well.

this change was target to testing branch.
but now when cat is out of the bag:
Do not expect much from devices without significant antenna gain (wAP and SXT series)
Performance should be similar to 66000MHz channel.

official announcements will be released only after product will be closer to finishing stage.
Hardware and software currently is close to that point.

As usualy I'm lucky to get broken hardware... Check this vid: https://drive.google.com/file/d/1kMckHbHpJ3C90IOOFgmKvybpNl2YpoUR/view?usp=sharing In short, there is something loose inside. Should I RMA it? or open and fix by myself? does opening voids waranty? Thanks for advice. Opening this device ...

Mikrotik guys, could you answer please? Will this bonding failover work properly in a PtMP setup, when done only on the station side? (Cube as station, connected to separate 5GHz and 60GHz sector APs on the same switch.) Yes, this can be reconfigured to work in such way. On 60GHz AP side add VLAN, ...

Looks like it will use bonding for failover https://help.mikrotik.com/docs/display/ROS/Fail-over+PtP+CLIexample Bonding failover is waaaaaaaaaaaaay too slow. Modern day failover times should be less than a second Only 1 way I know of to accomplish this in the MikroTik world, and thats with OSPF and...

This product is designed as PtP device or as CPE in PtMP setups, radiation is too narrow to be used for PtMP setups as AP.
High distance calibration for ap-bridge mode doesn't even exist on this device.
For AP please select appropriate device - wAP60G AP, or wAP60Gx3 AP.

I have seen that NRAY can be mounted rotated 90° changing antenna polarization this can help with rain and colocation?

Yes for experimental purposes, that's why we used horizontal Ethernet gland. Please keep in mind that dish design has drain hole, that needs to be sealed if used like that.

this is fixed in 6.48beta48, fix will also be merged in next stable release

Latest testing build includes some stability fixes, that will be put in upcoming current version.

May we expect the 60G devices to still be broken? I have talked with Mikrotik's support about this problem for some time. They have applied a fix in 6.48beta48, which fixed the issues for me. My 3,7km Link is stable again with 6.48beta48. It had massive stability issues (very frequent disconnects) ...

we have possible fix for this issue, that will be included in upcoming version.

From picture it seems, that nearby trees may be covering line of sight during winds, please try with higher frequencies as well.

Yes you can. Only USB lines are shared between mPCIe slot 1 and USB port. If lte card is installed in mPCIe2 and wireless card in mPCIe1 (wireless cards utilize PCI lines) USB can be used for LTE modem.

USB data lines are not connected on mAP lite.
Please consider mAP:
https://mikrotik.com/product/RBmAP2nD
as it has full USB functionality.

Device goes through pre-calibrated data over 3 degree span showing offset from center. Expecting that this will work outside calibrated span is ridiculous. If device is turned 20 degrees of, there is no way it's using main lobe, but is connected by side lobe that disturbs normal beamforming operatio...

everything seems to be in order, are devices aligned correctly? Is there anything blocking path?

I disagree. MikroTik engineers don't need to talk about customers individual deployments and environmental conditions. Just clarify how exactly it works For instance nobody seems to know anything about the sector numbers Are the sector numbers arrange in a grid like 1 2 3 4 5 6 7 8 9 Or maybe its 1...

Hello,

RSSI is too low, set tx-sector to auto and check if that improves situation.

And what about if its rapidly changing but the mount is solid? This should only happen after reboot or lost connection. Can reflection from a device behind it be the cause? Since its mounted directly behind a AF24HD Internal frequencies may overlap. For test you may try to move it a bit further if ...

frequency=auto picks first free channel (checks available SSIDs, in channel before selection) frequent tx-sector changes indicate, that there is issue related to devices moving in wind or alignment issues. In theory tx-sector should only change on very rare occasions - during first minutes of establ...

"Connected clients are treated as individual interfaces, after successful connection new station interface is created. "
https://wiki.mikrotik.com/wiki/Manual:Interface/W60G

Put wlan60-station-1 interface into bridge on master device side.

This can be done from RouterOS as well. Make simple Arduino||STM32 board with temperature sensor attached (DHT22 for example), that listens to serial input and answers with sensor data. In RouterOS if serial device is attached - disabled ppp-client is created. Make simple script, that does at-chat t...

thanks for reply. but it's not working

What device are you using? Is reset button acting as WPS button on this device as well?

system routerboard reset-button set on-event=??????
OK. now how to set event ?

Update: event on scripts must be entered.

wiki is also updated:
https://wiki.mikrotik.com/wiki/Manual:R ... et_buttons

Cabling also adds Voltage drop

Please make sure that you are using latest software releases - there a lot of quality improvements between older and newer software versions.
Alignment LEDs should be followed when alignment mode is on:
/interface w60g align wlan60-1

/interface lte at-chat lte input="AT+COPS\?"
should give back active PLMN

Unfortunately this is not supported on US modems

this feature is currently not available for US modems

bounding with active backup will switch over in less than 0.3 seconds if 60GHz link is lost

Currently only MikroTik to MikroTik communication is supported.

Well I'm out of ideas. Try a different channel? The 23% packet error rate isn't great. Still makes me think the signal's too hot. @antons? Signal may be too hot, but in this case it seems that this is caused somewhere else. Is there any other devices in between PCs and Wireless Wire dishes? My firs...

please add multiple parallel streams with -P option, for UDP, you have to set transfer speed as well.

Btest is limited by device resources. Please run Btest on other, powerfull devices through created 60GHz link

While Terragraph is still in development - Similar networks can be already made by using our devices, as explained by Attila Bologh in MUM Hungary 2019 https://mum.mikrotik.com/presentations/HU19/presentation_6777_1559506180.pdf This approach is a bit different - currently unavailable feature of AP ...

max L2MTU for w60g is 7882

could you please post configuration from both sides of the link?

please paste output from:
/interface w60g export hide-sensitive

Those are capabilities not supported by this modem.

Intel wireless adapters are not supported under RouterOS

I have a MIKRO TIK RBwAPG-60ad KIT.

Data is only updated when beamforming is working - we will fix this in upcoming versions

In 50m distance - there will be no issues getting full speed in all weather conditions

please make sure that you are using latest RouterOS versions. Btest has gone from single core process to multicore.

Hi All,

so disappointed with Mikrotik, after those years and ...

Looks like wrong baud rate.

Thanks Great and Easy but a couple other questions. 1. Devices are in transparent bridge (Layer 2) mode - this won't cause any issues, by exception if you are using same 192.168.88.0/24 network and trying to access the devices. To access the devices set correct IP addresse to the bridge interface. ...

Hello, most of the tests are done by using internal traffic generating tool - bandwidth test. This tool runs on internal device resources - and before latest updates utilized only one core of 4 core ARM CPU. With latest RouterOS releases this test runs on all cores, but we still recommend testing by...

please show us exactly how are you testing this. We get full speed on much higher distances by using same testing tools.
make sure that testing PCs has enough power, if possible run test in multi core mode, use multiple streams as well.

out of box devices are configured as transparent bridge (think of them as replacing existing cable). Addresses are static and you won't be able to access devices by using IP address if you are not in same subnet (traffic will still be passed through this wireless bridge). Other than that everything ...

we try alignment many times but this is best, why rssi not below -49... whats your suggestions for this distance ?

Signal is fine. is this PtP or PtMP setup? Is latest version used on both sides? Are devices mounted on fixed / stable pole?

how can fixed it

frequency-list was renamed to scan-list in one of beta releases.

All links works stable in heavy snow in Poland, our customers have 400mm and 600mm alu dishes. They use ros 6.42.11, 6.43.8 is not stable... what exactly is not stable? thank you for replay when test it it put frequency=auto and no connection ?? what you think about it "auto" does not inc...

Hello. We have a strange problem. We made a PtMP on wAP 60G (v6.44beta40) with 5 clients (4 LHG and 1 wAP same ROS version). Everything is working fine, but when anyone will shutdown MT (or reboot it) then we get disconnect on all stations and they don't want to connect again. We have to manually d...

please send supout.rif files from both of the devices to support@mikrotik.com

this issue will be addressed in upcoming releases (already fixed in beta70 - that will be released in upcoming days)

Hi, Im using a R11e-LTE in which im trying to use the cell locking feature in the newest os V6.44. However, i cannot send a AT chat command while the modem is in use and if i reset the modem the cell lock is removed as noted by the wiki. https://wiki.mikrotik.com/wiki/Manual:Interface/LTE#Using_Cel...

LEDs in your picture show that it's still connected

Where can one find the new snmp values ? "snmp - added "tx-ccq" ("mtxrWlStatTxCCQ") and "rx-ccq" ("mtxrWlStatRxCCQ") values;" Its not listen under "interface wireless" or "interface wireless registration-tabel". Checked both Ap a...

Rack "ears" can only be attached to non wireless version.

Add APN profile selection line together with changing SIM slot line:

/interface lte set lte1 apn-profiles=...

6.43rc3
*) wireless - improved compatibility with BCM chipset devices

Would it not be better to recommend 6.43.7 stable that would have all the RC stuff inn it?

Does this looks like suggesting older versions?

Are you running latest RouterOS versions?

Similar issues was fixed some time ago:

6.43rc3
*) wireless - improved compatibility with BCM chipset devices

Are you running latest RouterOS versions?

Multithread support for btest is already added:
Version 6.44beta39 has been released.
*) btest - added multithreading support for both UDP and TCP tests;

If you are using Wireless Wire kit - devices are pre-configured as transparent bridge and this usage case will work without any extra configuration.
In your case devices has not linked together, check if power is supplied to both of them.

Scan without sending out probe requests from device running passive scan.

is there any snow on front cover? Maybe device has alignment problems?

Finally test uses all cores of the routerboard... Have you checked BTest? MT Staff: why create speed-test? You already have BTest - develop it! :) I gave up on btest long time ago, and iperf is not always possible :( Please read carefully through change log: *) btest - added multithreading support ...

Yup also using the latest beta. On two separate links of +-1800m and 2000m cannot even make a single link. Using 64800 and 66000. You would think after aiming for a while there would at least be a connection - a bad one at least. please check if scan-list on "station-bridge" device includ...

Thank you for reporting this - this Quickset issue will be fixed in upcoming releases. Currently you can change address from IP menu

66GHz is mandatory on 2200+ meters!

Not exactly true -

connected: yes
frequency: 64800
remote-address: 04:D6:AA:AF:D3:C6
tx-mcs: 8
tx-phy-rate: 2.3Gbps
signal: 80
rssi: -57
distance: 2409.94m

https://wiki.mikrotik.com/wiki/Manual:S ... leshooting

Hello,
Is this issue reproducible in latest beta version?

Each version of RouterOS includes a lot of changes, it would help us, if you write versions you are using.

What RouterOS version are you using? Are you moving open Winbox screen around? Do you have stable connection to the device you are monitoring?

First five to ten minutes device is "learning" - there will be some drops in traffic during this period. We would recommend testing with traffic generated outside testing system (BTest is not the best tool to be used on device under test) If this issue repeats please send us supout.rif fil...

Anyone care to share with the less enlightened how exactly you go about enabling it in the CLI, and which beta version of the software you have to use? Is it under interface/wireless/channels/add?? On station make sure that frequency-list (or scan-list depending on used RouterOS version) includes d...

yes, align mode currently is only in latest beta versions.

upgrade you wAP60G devices and performance will be similar.

please provide versions used on those links and make sure you are running latest ones - there a lot of changes and improvements in latest releases. Antonsb latest FW 6.43.4 is not usable during the alignment the RSSI value update after several seconds (>30) or it don't update, I wasted 3 hours befo...

New beta versions has alignment mode included (it will update information much faster)
to use run from CLI:
/interface w60g align wlan60-1

please provide versions used on those links and make sure you are running latest ones - there a lot of changes and improvements in latest releases.

Form supout.rif files - RSSI signal on one side is way off. Latest beta version includes align mode - for easier alignment. it would help us improve, if we get some user feedback. To use align mode run on both sides: /interface w60g align wlan60-1 RSSI and sector information will change rapidly, adj...

Hello,
Those signal levels are too low for such distance.
What RouterOS version are you using? Are the dishes perfectly aligned?
Can you please send us supout.rif files from both sides to support@mikrotik.com ?

66000 GHz is non standard freq for this band? Will You implement 66960 GHz and 69120 GHz?

it's not a standard channel

typo of 66GHz

Much higher distances are available by using 64800 and 66000 MHz frequencies

please provide us more detailed info and send a support output file to support@mikrotik.com What wireless protocol you are using? How are you testing the speed/capacity? How often do you see this problem? I am using 802.11 speed/capacity - just looking on winbox and pinging other side. MKs are link...

All 60GHz devices in AP mode currently supports up to 8 clients.

*) wireless - improved stability for 802.11ac;
Any description of improve? Thanks

This fix should provide better rate selection at higher rates and at higher load.

Can we get access for this link or similar with such issue to run some tests and debug?
Please write to support@mikrotik.com

Search found 385 matches