2.9.48

RouterOS General
1

The demo.mt.lv shows this:

Trying 66.228.113.24...
Connected to 66.228.113.24.
Escape character is '^]'.

MikroTik v2.9.48
Login: demo
Password: 

  MMM      MMM       KKK                          TTTTTTTTTTT      KKK
  MMMM    MMMM       KKK                          TTTTTTTTTTT      KKK
  MMM MMMM MMM  III  KKK  KKK  RRRRRR     OOOOOO      TTT     III  KKK  KKK
  MMM  MM  MMM  III  KKKKK     RRR  RRR  OOO  OOO     TTT     III  KKKKK
  MMM      MMM  III  KKK KKK   RRRRRR    OOO  OOO     TTT     III  KKK KKK
  MMM      MMM  III  KKK  KKK  RRR  RRR   OOOOOO      TTT     III  KKK  KKK

  MikroTik RouterOS 2.9.48 (c) 1999-2007       http://www.mikrotik.com/


Terminal unknown detected, using single line input mode
[demo@demo.mt.lv] >

Router running for at least one day.

The download page shows us 2.9.46 for both x86 and routerboards.
Any changes made ?

2

Guess not.

3

See http://forum.mikrotik.com/t/3-0rc7/16465/6

4

it’s on the web

5

*) fixed bug in routing-test package;

What bug? Don’t know wether it makes an update neccesary.

Stefan

6

only one way to find out

7

Hold on to your subnets boys…

That comment makes me all warm and fuzzy !!!..

8

it mentions a bug, it’s not actually a “problem”. it’s hard to tell what problems a bug caused, probably different kinds. if users report problems, we look for causes. then a bug is found, fixed and this solves the reported problems. usually one bug can cause many problems, but it’s not possible to tell what problems as configurations are many.

9

Hi Normis,

what I wanted is some feeling wether to update or not (some sort of
severity-Information) That’s what release notes are for.

“fixed a bug” is no information. I know there are bugs. Even a good programmer
makes at least one bug every 4k of source code.

So if you say it’s “not actually a problem” it’s a bug which not likely kills
one of my ap’s. So I’m happy and do not touch my running systems.

Stefan

10

Hi,

found the wireless-crd package. Gives me two countries for
the additional frequencies in germany. Thanks MT
(waiting for the A-TP stuff in 3.0 to have the full power :sunglasses: ).
But for some short shot’s it’ll be real helpful.

To change to the new frequencies with winbox you’ve to
select a band with frequencies which are available in both
“countries” e.g. 5GHz-10MHz, select the new country and
then select 5GHz again. So I see the 5 frequencies in upper
Band.

What I’m wondering. I tried this with a R52h and saw
24db outputpower with 5-24MBit (ok) but I saw lower
power at higher speeds.

[admin@a14] > interface wireless monitor wlan1 once
                 status: running-ap
                   band: 5ghz
              frequency: 5770MHz
            noise-floor: -103dBm
         overall-tx-ccq: 67%
     registered-clients: 0
  authenticated-clients: 0
    current-ack-timeout: 25
       current-distance: 25
                nstreme: no
      current-tx-powers: 6Mbps:24,9Mbps:24,12Mbps:24,18Mbps:24,24Mbps:24,36Mbps:22,48Mbps:20,54Mbps:19
    notify-external-fdb: no

R52h should have enough power to give 24 at 54Mbps too ??

[admin@a14] > interface wireless print                 
Flags: X - disabled, R - running 
 0    ;;; w1
      name="wlan1" mtu=1500 mac-address=00:0C:42:18:0F:86 arp=enabled disable-running-check=no 
      interface-type=Atheros AR5413 radio-name="w1" mode=ap-bridge ssid="xxxxx" area="" 
      frequency-mode=regulatory-domain country=germany 5.8 fixed p-p antenna-gain=0 frequency=5770 
      band=5ghz scan-list=default rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps 
      supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps basic-rates-b=1Mbps 
      basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power-mode=default 
      noise-floor-threshold=default periodic-calibration=default periodic-calibration-interval=60 
      burst-time=disabled dfs-mode=no-radar-detect antenna-mode=ant-a wds-mode=disabled 
      wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 wds-ignore-ssid=no 
      update-stats-interval=disabled default-authentication=yes default-forwarding=yes 
      default-ap-tx-limit=0 default-client-tx-limit=0 proprietary-extensions=post-2.9.25 hide-ssid=no 
      security-profile=yyyyy disconnect-timeout=3s on-fail-retry-time=100ms hw-retries=15 
      preamble-mode=both compression=no allow-sharedkey=no

Stefan